Kichler Lighting SPYRA User manual

62" LED SPYRA
INSTRUCTION MANUAL
Product images may vary slightly from actual product.

62" LED SPYRA | 3
TABLE OF CONTENTS
KICHLER.COM
SAFETY RULES ...........................................................................4
TOOLS AND MATERIALS REQUIRED ................................5
PACKAGE CONTENTS .................................................................5
MOUNTING OPTIONS .............................................................6
HANGING THE FAN .................................................................7
INSTALLATION OF SAFETY SUPPORT ..........................9
ATTACHING THE FAN BLADES .........................................12
INSTALLING THE SWITCH HOUSING .............................13
INSTALLLING THE LED ASSEMBLY ..........................................13
INSTALLING THE GLASS SHADE ...................................14
WALL CONTROL INSTALLATION .....................................15
PAIRING PROCEDURES ..................................................... 16
USING YOUR CEILING FAN ...............................................17
TROUBLESHOOTING ...........................................................18
FCC WARNING .........................................................................19
SPECIFICATIONS ...................................................................20

4 | KICHLER.COM 62" LED SPYRA | 5
TOOLS REQUIRED
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
SAFETY RULES
1. To reduce the risk of electric shock, insure electricity has been turned
2. All wiring must be in accordance with the National Electrical Code
and local electrical codes. Electrical installation should be performed
3. WARNING: Suitable for use with solid- state speed controls.
4. WARNING: To reduce the risk of personal injury, use only the two
steel screws (and lock washers) provided with the outlet box for
mounting to the outlet box. Most outlet boxes commonly used for the
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED
“ACCEPTABLE FOR FAN SUPPORT”.
5. The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 50 pounds. Use only CUL
Listed outlet boxes marked “FOR FAN SUPPORT”.
6. The fan must be mounted with a minimum of 7 feet clearance from
the trailing edge of the blades to the floor.
7. Do not operate reversing switch while fan blades are in motion.
direction.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades.
A dry dust cloth or lightly dampened cloth will be suitable for most
cleaning.
11. After making the electrical connections, spliced conductors should
be turned upward and pushed carefully up into outlet box. The wires
should be spread apart with the ground wire and white
12. (common) wire to one side with the black (load) wire to the other side
of the outlet box.
13. Electrical diagrams are reference only. Light kits that are not packed
with the fan must be CUL Listed and marked suitable for use with
the model fan you are installing. Switches must be CUL General Use
Switches. Refer to the Instructions packaged with the light kits and
switches for proper assembly.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT
BEND THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)
DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT
OBJECTS IN THE PATH OF THE BLADES.
SPECIAL NOTICE: This appliance is equipped with a “Wattage Limiting
Device” required by the United States Department of Energy. The
device has been installed at the factory and can not be removed.
Installing Lamps in excess of 190 total watts will disable the unit’s light
lamps totaling less that 190 watts and then turning the power back on.
PACKAGE CONTENTS
Unpack your fan and check the
contents . You should have the
following items:
A. Mounting bracket
B. Ball / downrod assembly (1)
C. Canopy
D. Canopy Hole Cover
E. Coupling cover
F. Motor Body
G. Blade Trim (3)
H. Blade (3)
I. Switch Housing
J. LED Assembly
K. Glass Shade
L. Power Kit
M. Package hardware
1) Mounting hardware: Wood
screws(2) , flat washers (2) ,
screws (2) , Spring washers (2),
wire nuts (3)
2) Blade attachment hardware :
Screws (2)
3) Balance kit
4)
5)
Screw hardware:
Screw (3)
Safety Cable Hardware:
wood screw (1), Spring washer (1),
Flat washer (1)
A
B
C
D
E
F
G
H
I
J
K
LM

6 | KICHLER.COM 62" LED SPYRA | 7
MOUNTING OPTIONS
If there isn’t an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect the
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box and its
support must be able to fully support the moving weight of the fan
(at least 50 lbs). Do not use plastic outlet boxes.
box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted)
ceiling, you may need a longer downrod to maintain proper
clearance between the tip of the blade and the ceiling. A minimum
clearance of 12” is suggested for optimal operation.
NOTE: Depending on the location you have selected for installation,
you may need to purchase and install a “Joist Hanger” for the
support of the outlet box. Make sure the joist hanger you purchase
has been designed for use with ceiling fans. (Fig. 4)
HANGING THE FAN
REMEMBER to turn o the power before you begin installation.
This is necessary for your safety and also the proper programming
of the control system.
To properly install your ceiling fan, follow the steps below.
Step 1. Before attaching fan to outlet box (not included), ensure the
outlet box is securely fastened to at least two points to a structural ceiling
member (a loose box will cause the fan to wobble). Pass the 120 volt supply
wires from the ceiling outlet box through the center of the ceiling mounting
bracket. Install mounting bracket to outlet box in ceiling using the screws
and washers included with the outlet box or screws and washers in the
hardware bag. (Fig. 5)
Step 2. Remove the hanger ball from downrod assembly by loosening
set screws , removing the cross pin, and sliding ball o the rod. ( Fig. 6)
Fig. 1
Outlet box
Outlet box
Fig. 2
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Fig. 3
ANGLED CEILING
MAXIMUM 20°ANGLE
Outlet box
Fig. 4
Fig. 5
Fig. 6
ETL Listed Outlet Box
Ceiling Mounting Bracket
Flat Washer
Screw
Hanger Ball
Set Screw
Downrod
Cross Pin

8 | KICHLER.COM 62" LED SPYRA | 9
HANGING THE FAN
Step 3. Loosen the two set screws and remove the clip and
cross pin from the top coupling of the motor body.
Carefully feed the fan wires up through the downrod. Thread
the downrod onto the motor coupling until the cross pin
holes are aligned. Next, replace the cross pin and clip,
and tighten both set screws. (Fig. 7)
Step 4. Slip the coupling cover, canopy hole cover and canopy
onto the downrod. Carefully reinstall the hanger ball onto the
downrod . Make sure the cross pin is in the correct position and
the set screws are tight and the wires are not twisted . ( Fig. 8)
HANGING THE FAN
Step 5. Now lift the motor body into position and place the hanger ball into
the hanger bracket. Rotate until the "Check Tab" has dropped into the
"Registration Slot " and seats firmly. ( Fig. 9) The entire motor body should
not rotate is this is done correctly.
WARNING: Failure to properly seat the "Check Tab" can damage the ceiling
fan during operation.
A safety support cable is provided to help prevent the ceiling fan
from failing, please install it as follows.
INSTALLATION OF SAFETY SUPPORT
(required for Canadian installation ONLY)
Step 1. Drive a wood screw and washers into the side of the brace
that holds the outlet box. Leave 3mm (1/8") of space between the
support brace and the washer. (Fig. 10)
Canopy
Hanger Ball
Canopy Hole Cover
Coupling Cover
Motor Body
Fig. 7
Fig. 8
Clip
Set Screw
Cross Pin
Set Screw
Clip Cross Pin
Check Tab Registration Slot
Flat Washer
Wood Screw
Spring Washer
Outlet Box
Support Brace
Ceiling
Fig. 10
Fig. 9

10 | KICHLER.COM 62" LED SPYRA | 11
INSTALLATION OF SAFETY SUPPORT
(required for Canadian installation ONLY)
FINISHING THE INSTALLATION
Step 2. Insert the safety cable through the mounting bracket and one of the holes in the
outlet box into the ceiling. Adjust the length of the safety cable to reach the screw and
washers by pulling the extra cable through the cable clamp until the overall lenght is correct,
put the end of the cable back through the cabel clamp, forming a loop at the end of the cable.
Tighten the cable clamp securely. Now, put the loop in the end of the safety cabel over the
wood screw and under the washer. Tighten the wood screw securely. (Fig. 11)
Step 1. Remove one of the two shoulder screws in the mounting bracket. Loosen
the second shoulder screw without fully removing it. (Fig. 12)
NOTE: Although the safety support cable is required for Canadian installations only.
It’s a good idea to make the attachment with any installation.
NOTE: Before continuing , make sure the power is disconnected by turning o the circuit
breaker of removing the fuse at the circuit box.
FINISHING THE INSTALLATION
Step 2. Assemble canopy by rotating key slot in canopy over shoulder
screw in mounting bracket. Tighten shoulder screw. Fully assemble
and tighten second shoulder screw that was previously removed.
(Fig. 13)
Step 3.Securely attach and tighten the canopy hole cover over the
shoulder screws in the mounting bracket utilizing the keyslot
twist-lock feature. (Fig. 14)
Mounting Bracket
Shoulder Screw
Safety Cable Bolt
Wood Screw
Fig. 11
Fig. 12
Shoulder Screw
Canopy
Canopy Hole Cover
Shoulder Screw
Fig. 13
Fig. 14

12 | KICHLER.COM 62" LED SPYRA | 13
ATTACHED THE FAN BLADES
Step 1. Remove and discard the shipping block by removing the screw.
Line up the holes in the blade trim with the holes in the bottom of the
motor body (marked A-A). And tighten them with two pre-installed
screws provided. Repeat steps for the remaining blade trim. (Fig. 15)
Step 2. Line up the holes in the blade with the holes in the bottom
of the motor body (marked B-B). Faster blade to the bottom of the
motor body with two “preinstalled” screws provided. Repeat steps for
the remaining blades. (Fig. 16)
INSTALLING THE SWITCH HOUSING
INSTALLING THE LED ASSEMBLY
Step 1. Remove one screw on the mounting plate, which near
the red dot label and loosen the other two (do not remove). Place
the two slot holes on the switch housing over the 2 screws previously
loosened from the mounting plate. Rotate the switch housing until
it locks in place at the narrow end of the key holes. Securely by tightening
the 2 screws previously loosened and the one previously removed. (Fig. 17)
NOTE: Before continuing, make sure the power is disconnected by
turning o the circuit breaker of removing the fuse at the circuit box.
Step 1. Remove the three screws in the switch housing. (Fig. 18)
Blade
Fig. 16
Motor Body
Blade Trim
Fig. 15
Motor Body
ScrewShipping Block
Fig. 17
Fig. 18
Switch Housing
Mounting Plate
Screw
Switch Housing
Screw

14 | KICHLER.COM 62" LED SPYRA | 15
INSTALLING THE LED ASSEMBLY
INSTALLING THE GLASS SHADE
Step 2. Connect the 2 single pin connectors from the LED assembly
to the 2 single pin connectors from motor body, BLACK to BLACK,
WHITE to WHITE. Assembly the LED assembly to the switch housing
and tighten them by the three screws removed previously. (Fig. 19)
Step 1. Secure the glass shade to switch housing by twisting in a
clockwise direction. Do not over-tighten. (Fig. 20)
WALL CONTROL INSTALLATION
Caution: To reduce the risk of electrical shock, disconnect the
electrical supply circuit before installing the fan, light kit or receiver.
Step 3. Connect one black wire of wall control to the "hot"
wire (house source). Securely connect wires with wire
connectors supplied. (Fig. 25)
Step 4. Connect another black wire of wall control to the
"load" (black) wire in the wall box. Securly connect wires
with wire connector supplied.
Step 1. Remove faceplate and screws from existing wall control (if present).
Pull control out from the wall box. Determine the "hot" wire and
"load" wire and disconnect these wires from control (Fig. 24). Do not
attempt to disconnect any wires not already connected to existing control.
NOTE: Make all wiring conenctions using wire connectors (supplied).
Make sure that all connections are tight, including ground, and that
no bare wire is visible at the wire connectors, except for the ground wire.
Step 2. Before installing the wall control, place it in "OFF" mode
by press the button. (higher than faceplate).
HOT BLK
BLACK
BLACK
LOAD
GROUND
NEUTRAL
Fig. 22
Fig. 21
BLK
BLACK
GROUND
TO LOAD
HOT
TO 120V SOURCE
Fig. 19
Switch Housing
LED Assembly
Fig. 20
Screw
Screw
Switch Housing

16 | KICHLER.COM 62" LED SPYRA | 17
PAIRING PROCEDURES
IMPORTANT: Ceiling fan blades MUST be
installed before paring procedure can begin.
USING YOUR CEILING FAN
Step 3. Try dierent speed setting on wall control
to ensure the fan is now fully functional.
If programming is unsuccessful, retry the process
starting from step 1 agains.
Step 2. Within 60 seconds of press the" "switch to
"ON" and then hold the" "button fro 3 to 5 seconds,
light will blink twice. The remove till now be programmed
to your fan and ready for use.
IMPORTANT: Do not interrupt the conditioning
until the fan comes to a complete stop in
approximately 5 minutes. All functions of the
control will be rejected during conditioning.
Step 1. Turn the wall control to "OFF" postion.
Restore electricity to the ceiling fan branch circuit
at the circuit breaker or fuse box.
Press the" "button once to turn ON (or OFF) the
fan. (Fig. 26)
If airflow is desired in the opposition direction,
press the" "button. The fan must be operating at
any speed for the reverse button to function. The
blades will turn in the opposite direction and
reverse the airflow. (Fig. 26)
Fig. 23
To turn the light on and o, press and release the
light" "button. To set the light intensity, press and
hold the light button. The light will turn on at the
light intensity previously selected. (Fig. 26)
To set the desired fan speed, press and hold the" "
button to decrease and increase the speed. (Fig. 26) Light Button
Fan Speed Button
Airflow Direction
Power Button
Indication Light
(Power)

18 | KICHLER.COM 62" LED SPYRA | 19
TROUBLESHOOTING FCC WARNING
Problem
Fan will not start.
Fan sounds noisy.
Fan wobble.
Remote control
malfunction.
Solution
1. Check circuit fuses or breakers.
2. Check all electrical connections to insure proper contact.
CAUTION: Make sure the main power is OFF when checking any electrical connection.
3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.
4. Insure the batteries have a good charge.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade brackets to the motor are tight.
3. Make sure wire nut connections are not rubbing against each other or the interior
wall of the switch housing. CAUTION: Make sure main power is o.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.
5. If using an optional light kit, make sure the screws securing the glassware are tight.
Make sure the light bulbs are not touching any other component.
6. Do not connect this fan to a wall mounted variable speed control(s).
They are not compatible with ceiling fan motors or remote controls.
7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal.
Check this level by selecting a point on the ceiling above the tip of one of the blades.
Measure this distance. Rotate the fan until the next blade is positioned for measurement.
Repeat for each blade. The distance deviation should be equal within 1/8".
3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades
can redistribute the weight and possibly result in smoother operation.
1. Ceiling Fans with remote control systems CAN NOT be operated in
conjunction with any other control system EXCEPT a basic On/O wall switch, if desired.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifictions not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installatio. This equipment generates, uses and can rediate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interfenence to radio or television reception,
which can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate teh receiving antenna, increase the separation between the equipment and receiver,
and connect the equipment into an outlet on a circuit dierent from that no which the fan is connected.