Kikusui PCR-WE series User manual

PCR1000WE
PCR2000WE
PCR-WE2 Series AC Power Supply
PCR3000WE2
PCR6000WE2/PCR6000WE2R
PCR12000WE2/PCR12000WE2R
PCR18000WE2/PCR18000WE2R
PCR24000WE2/PCR24000WE2R
PCR30000WE2/PCR30000WE2R
PCR36000WE2/PCR36000WE2R
Communication Interface Manual
PCR-WE Series AC Power Supply
Part N0. IA005343
Jul 2019

KIKUSUI Electronics Corp. 2
INDEX
Command List............................. 7
Introduction............................... 25
Reading environment......................... 25
Intended readers................................ 25
Structure of the manual ..................... 26
Trademarks........................................ 26
Firmware version of the product to which
this manual applies............................ 26
Measuring instrument interface
standards........................................... 27
Copyright ........................................... 27
Installing the VISA Library....... 28
Setting Up the Interface ........... 29
RS232C (standard)............................ 30
USB (standard).................................. 33
LAN (standard) .................................. 34
Accessing and Operating the Product
from a Web Browser (LAN)................ 40
GPIB (option)..................................... 49
About Commands..................... 51
Command Hierarchy.......................... 51
Command Syntax .............................. 52
Parameters................................ 55
Non-numeric parameters................... 55
Numeric parameters .......................... 56
Special form numeric parameters...... 57
Phase designation (channel list)........ 58
Measurement units ............................ 58
IEEE 488.2 common commands .
59
*CLS .................................................. 59
*ESE .................................................. 60
*ESR.................................................. 61
*IDN ................................................... 62
*OPC.................................................. 63
*OPT.................................................. 64
*PSC.................................................. 65
*RCL .................................................. 66
*RST .................................................. 67
*SAV .................................................. 69
*SRE.................................................. 70
*STB .................................................. 71
*TRG.................................................. 72
*TST................................................... 73
*WAI................................................... 74
ABORt Command ..................... 75
ABOR................................................. 75
ABOR:ACQ........................................ 76
ABOR:PROG..................................... 77
ABOR:SIM ......................................... 78
ABOR:TRAN...................................... 79
DISPlay Command.................... 80
DISP:CONT ....................................... 80
DISP:PHAS........................................ 81
DISP:MMOD:CURR........................... 82
DISP:MMOD:VOLT............................ 83
DISP:MMOD:VOLT:LTL ..................... 84
HCOPy Command..................... 85
HCOP:SDUM:DATA?......................... 85
INITiate Command .................... 86
INIT:ACQ............................................ 86
INIT:PROG......................................... 87
INIT:SIM............................................. 88
INIT:TRAN.......................................... 89
INSTrument Command............. 90
INST/ INST:NSEL .............................. 90
INST:COUP........................................ 91
LXI Command ........................... 92
LXI:IDEN............................................ 92

INDEX
PCR-WE Interface Manual
3
MEASure/FETCh Command .... 93
FETC:<meas-item>/ MEAS:<meas-
item>.................................................. 94
FETC:ARR:<harm-item>?/
MEAS:ARR:<harm-item>?................. 96
MEMory Command................... 97
MEM:REC.......................................... 97
MEM:REC:CONF............................... 98
MEM:REC:PREV............................... 99
MEM:SAVE ...................................... 100
OUTPut Command.................. 101
OUTP............................................... 101
OUTP:IMP ....................................... 102
OUTP:IMP:REAC ............................ 103
OUTP:IMP:REAL............................. 104
OUTP:PHAS:OFF............................ 105
OUTP:PHAS:OFF:LEV.................... 106
OUTP:PHAS:ON.............................. 107
OUTP:PHAS:ON:LEV...................... 108
OUTP:PON...................................... 109
OUTP:PROT:CLE .............................110
OUTP:PROT:WDOG......................... 111
OUTP:PROT:WDOG:DEL.................112
OUTP:SST........................................113
OUTP:SST:FALL...............................114
OUTP:SST:TIME...............................115
OUTP:SST:TIME:FALL .....................116
PROGram Command...............117
PROG:CLE .......................................117
PROG:EDIT......................................118
PROG:EDIT:FUNC:BANK................ 120
PROG:EDIT:JUMP........................... 121
PROG:EDIT:IMP.............................. 122
PROG:EDIT:IMP:REAC................... 123
PROG:EDIT:IMP:REAL.................... 124
PROG:EDIT:PHAS:RAMP ............... 125
PROG:EDIT:PHAS:STAR ................ 126
PROG:EDIT:PHAS:STOP................ 127
PROG:EDIT:PHAS:UOFF................ 128
PROG:EDIT:PHAS:UV..................... 129
PROG:EDIT:PHAS:UW.................... 130
PROG:EDIT:VOLT ........................... 131
PROG:EDIT:VOLT:OFFS ................. 132
PROG:EXEC ................................... 133
PROG:LOOP ................................... 134
PROG:STAT..................................... 135
PROG:STEP:END ........................... 136
PROG:STEP:STAR ......................... 137
SENSe Command ................... 138
SENS:AVER:COUN......................... 138
SENS:CURR:HOLD:CLE................. 139
SENS:CURR:HOLD:TIME............... 140
SENS:VOLT:AVER:COUN ............... 141
SENS:VOLT:HOLD:CLE .................. 142
SENS:VOLT:HOLD:TIME................. 143
SIMulation Command............. 144
SIM:EXEC........................................ 144
SIM:POL .......................................... 145
SIM:REP:COUN .............................. 146
SIM:STAT......................................... 147
SIM:T1:PHAS .................................. 148
SIM:T1:PHAS:STAT......................... 149
SIM:T1:TIME.................................... 150
SIM:T2:TIME.................................... 151
SIM:T3:TIME.................................... 152
SIM:T3:VOLT ................................... 153
SIM:T4:TIME.................................... 154
SIM:T5:CYCL................................... 155
SIM:T5:CYCL:STAT......................... 156
SIM:T5:TIME.................................... 157
[SOURce:]CURRent Command ...
158
CURR .............................................. 158
CURR:PEAK.................................... 159
CURR:PEAK:LOW........................... 160
CURR:PROT:STAT .......................... 161
CURR:PROT:TRIP:DEL................... 162
[SOURce:]FREQuency Command
163
FREQ............................................... 163

KIKUSUI Electronics Corp. 4
FREQ:LIM:LOW............................... 164
FREQ:LIM:UPP ............................... 165
FREQ:SYNC.................................... 166
FREQ:SYNC:MODE........................ 167
FREQ:SYNC:PHAS:DEL................. 168
FREQ:TRIG ..................................... 169
[SOURce:]FUNCtion Command ..
170
FUNC:BANK.................................... 170
[SOURce:]VOLTage Command....
171
VOLT................................................ 171
VOLT:COMP:MODE ........................ 172
VOLT:COMP:RADJ.......................... 173
VOLT:COMP:SOFT:CONT............... 174
VOLT:COMP:SOFT:TERM............... 175
VOLT:EXT:INP:EXTDC:ADJ:GAIN... 176
VOLT:EXT:INP:EXTDC:ADJ:OFFS.. 177
VOLT:EXT:INP:EXTDC:APER ......... 178
VOLT:EXT:INP:EXTDC:SIGN:POL .. 179
VOLT:EXT:INP:EXTDC:SIGN:SOUR
180
VOLT:EXT:INP:FUNC:MODE........... 181
VOLT:EXT:INP:VPR:ADJ:GAIN ....... 182
VOLT:EXT:INP:VPR:ADJ:OFFS....... 183
VOLT:EXT:INP:VPR:MAP ................ 184
VOLT:EXT:INP:VPR:STAT ............... 185
VOLT:LIM:LOW................................ 186
VOLT:LIM:UPP................................. 187
VOLT:LTL ......................................... 188
VOLT:OFFS ..................................... 189
VOLT:OFFS:LIM:LOW ..................... 190
VOLT:OFFS:LIM:UPP ...................... 191
VOLT:OFFS:LTL............................... 192
VOLT:OFFS:TRIG............................ 193
VOLT:PROT:LOW ............................ 194
VOLT:PROT:PEAK:LOW.................. 195
VOLT:PROT:PEAK:UPP .................. 196
VOLT:PROT:LOW:STAT................... 197
VOLT:PROT:UPP ............................. 198
VOLT:RANG..................................... 199
VOLT:RESP ..................................... 200
VOLT:TRIG ...................................... 201
STATus Command .................. 202
Status Report Structure ................... 202
Architecture...................................... 204
Status byte register.......................... 205
Event status register........................ 206
OPERation status register ............... 207
STAT:OPER ..................................... 208
STAT:OPER:COND.......................... 209
STAT:OPER:ENAB .......................... 210
STAT:OPER:NTR..............................211
STAT:OPER:PTR ............................. 212
OPERation:INSTrument subregister 213
STAT:OPER:INST ............................ 214
STAT:OPER:INST:COND................. 215
STAT:OPER:INST:ENAB.................. 216
STAT:OPER:INST:NTR .................... 217
STAT:OPER:INST:PTR .................... 218
OPERation:INSTrument:ISUMma
ry{1|2|3} subregister......................... 219
STAT:OPER:INST:ISUM{1|2|3} ........ 220
STAT:OPER:INST:ISUM{1|2|3}:COND...
221
STAT:OPER:INST:ISUM{1|2|3}:ENAB ...
222
STAT:OPER:INST:ISUM{1|2|3}:NTR 223
STAT:OPER:INST:ISUM{1|2|3}:PTR 224
QUEStionable status register .......... 225
STAT:QUES ..................................... 226
STAT:QUES:COND.......................... 227
STAT:QUES:ENAB .......................... 228
STAT:QUES:NTR............................. 229
STAT:QUES:PTR ............................. 230
QUEStionable:INSTrument subregister.
231
STAT:QUES:INST ............................ 232
STAT:QUES:INST:COND................. 233
STAT:QUES:INST:ENAB.................. 234
STAT:QUES:INST:NTR .................... 235
STAT:QUES:INST:PTR .................... 236
QUEStionable:INSTrument:ISUMmary{1
|2|3} subregister............................... 237

INDEX
PCR-WE Interface Manual
5
STAT:QUES:INST:ISUM{1|2|3} ........ 238
STAT:QUES:INST:ISUM{1|2|3}:COND...
239
STAT:QUES:INST:ISUM{1|2|3}:ENAB ...
240
STAT:QUES:INST:ISUM{1|2|3}:NTR 241
STAT:QUES:INST:ISUM{1|2|3}:PTR 242
Preset status.................................... 243
STAT:PRES...................................... 243
SYSTem Command................. 244
SYST:COMM:RLST ......................... 244
SYST:CONF:ACC............................ 245
SYST:CONF:ADJ:VOLT:FINE.......... 246
SYST:CONF:ADJ:VOLT:TERM:MODE ..
247
SYST:CONF:FORM:FRAM.............. 248
SYST:CONF:FORM:FRAM:INFO .... 249
SYST:CONF:FORM:PMOD ............. 250
SYST:CONF:FORM:PMOD:INFO.... 251
SYST:CONF:FORM:PSAV:MAX...... 252
SYST:CONF:FORM:PSAV:MOD ..... 253
SYST:CONF:FORM:PSAV:RES ...... 254
SYST:CONF:PHAS:UOFF............... 255
SYST:CONF:PHAS:UV.................... 256
SYST:CONF:PHAS:UW................... 257
SYST:CONF:PON:STAT .................. 258
SYST:CONF:SSUP.......................... 259
SYST:CONF:WIR/ SYST:CONF:NOUT .
260
SYST:DATE ..................................... 261
SYST:ERR ....................................... 262
SYST:ERR:COUN............................ 263
SYST:EXT:DIG:READ...................... 264
SYST:EXT:DIG:WRIT....................... 265
SYST:EXT:SIGIN:MAP..................... 266
SYST:EXT:SIGIN:POL ..................... 267
SYST:EXT:SIGIN:STAT.................... 268
SYST:EXT:SIGOUT:MAP................. 269
SYST:EXT:SIGOUT:POL.................. 270
SYST:EXT:SIGOUT:STAT ................ 271
SYST:EXT:SSIGIO:MAP.................. 272
SYST:EXT:SSIGIO:POL................... 274
SYST:EXT:SSIGIO:STAT ................. 275
SYST:KLOC..................................... 276
SYST:LOC/ SYST:REM/ SYST:RWL 277
SYST:OPT ....................................... 278
SYST:PASS ..................................... 279
SYST:PASS:CDIS............................ 280
SYST:PASS:NEW ............................ 281
SYST:PASS:STAT............................ 282
SYST:SEC:IMM ............................... 283
SYST:SLE........................................ 284
SYST:SLE:EXEC ............................. 285
SYST:SLE:TIME .............................. 286
SYST:TIME ...................................... 287
SYST:TIME:ADJ .............................. 288
SYST:TZON..................................... 289
SYST:TZON:CAT ............................. 290
SYST:VERS..................................... 291
TRIGger Command................. 292
TRIG:ACQ ....................................... 292
TRIG:ACQ:SOUR............................ 293
TRIG:PROG..................................... 294
TRIG:PROG:SOUR ......................... 295
TRIG:SIM......................................... 296
TRIG:SIM:SOUR ............................. 297
TRIG:TRAN ..................................... 298
TRIG:TRAN:SOUR.......................... 299
WAVE Command..................... 300
WAVE:DATA:ARB ............................ 300
WAVE:DATA:CLIP............................ 301
WAVE:DATA:IECP ........................... 302
WAVE:DATA:POIN........................... 303
WAVE:DATA:SIN ............................. 304
WAVE:DATA:TYPE .......................... 305
List of Errors........................... 306
Command errors.............................. 306
Execution errors............................... 307
Product-specific errors..................... 308
Query errors..................................... 308
Operation complete event errors ..... 309
Product-dependent errors................ 309

KIKUSUI Electronics Corp. 6
Command processing time ... 312
Tutorial..................................... 313
Programming AC Output.................. 313
Programming DC Output ................. 315
Trigger Subsystem........................... 316
Changing the output with triggers
(TRANsient)..................................... 318
Measurement (ACQuire).................. 321
Power line abnormality simulations
(SIMulation) ..................................... 326
Sequence Operation (PROGram).... 329
Waiting for Operation Complete ...... 332
Status Monitoring............................. 333
Error Checking................................. 336
Visual Basic 2017 ............................ 337

Command List
PCR-WE Interface Manual
7
IEEE 488.2 common commands
*CLS
Clears all event registers including the status byte, event status, and error queue.
*ESE
Sets the event status enable register that is counted by the event summary bit (ESB) of the
status byte.
*ESR
Queries the event status register. The event status register is cleared when read.
*IDN
Queries the model name and firmware version of the product.
*OPC
Sets the OPC bit (bit 0) of the event status register when all the commands that are in
standby have been processed.
*OPT
Queries the optional interface boards that are installed in the product.
*PSC
Sets whether the event status enable register and service request enable register are
cleared when the POWER switch is turned on.
*RCL
Recalls memory content.
*RST
Resets a portion of the product settings.
*SAV
Saves the panel settings to memory.
*SRE
Sets the service request enable register.
*STB
Queries the contents of the status byte register and the MSS (master summary status)
message.
Command List

KIKUSUI Electronics Corp. 8
*TRG
Trigger command.
*TST
Executes a self-test.
*WAI
Prevents the device from executing subsequent commands until all operations that are in
standby have completed.
ABORt Command
ABOR
Aborts configuration, changes, measurements, and other operations in all trigger
subsystems (TRANsient, ACQuire, SIMulation, PROGram).
ABOR:ACQ
Aborts measurement operations.
ABOR:PROG
Stops the trigger function of the sequence operation.
ABOR:SIM
Aborts the trigger function of the power line abnormality simulation.
ABOR:TRAN
Aborts the trigger function for configuration changes.
DISPlay Command
DISP:CONT
Adjusts the screen brightness.
DISP:PHAS
Selects the phase to display on the panel.
DISP:MMOD:CURR
Sets the current, power, or power factor to display on the screen.
DISP:MMOD:VOLT
Sets the voltage (rms value, peak value, average value) to display on the screen.

HCOPy Command
PCR-WE Interface Manual
9
DISP:MMOD:VOLT:LTL
Sets the voltage (phase voltage, line voltage) to display on the screen.
HCOPy Command
HCOP:SDUM:DATA?
Retrieves the screen capture of the present screen.
INITiate Command
INIT:ACQ
These commands invalidate the present measured data and start a new measurement.
INIT:PROG
Executes a sequence.
INIT:SIM
Executes a power line abnormality simulation.
INIT:TRAN
Starts the trigger function.
INSTrument Command
INST/ INST:NSEL
Selects the phase that SOURce and MEASure/FETCh commands apply to.
INST:COUP
Sets whether to select all phases.
LXI Command
LXI:IDEN
Turns the identification display on or off.
MEASure/FETCh Command
FETC:<meas-item>/ MEAS:<meas-item>
Queries the scalar measurement data specified with <meas-item>.

KIKUSUI Electronics Corp. 10
FETC:ARR:<harm-item>?/ MEAS:ARR:<harm-item>?
Queries the harmonic data specified with <harm-item>.
MEMory Command
MEM:REC
Recalls contents saved in the ABC memory.
MEM:REC:CONF
Sets whether to the memory content is to be confirmed before recalling the ABC memory
from the panel.
MEM:REC:PREV
Displays the contents that are stored in the ABC memory.
MEM:SAVE
Saves the frequency, AC voltage, DC voltage, and waveform bank number to memory.
OUTPut Command
OUTP
Set the output to on or off.
OUTP:IMP
Enables or disables the output impedance.
OUTP:IMP:REAC
Sets the reactance component of the output impedances.
OUTP:IMP:REAL
Sets the resistance component of the output impedances.
OUTP:PHAS:OFF
Enables or disables output-off phase control.
OUTP:PHAS:OFF:LEV
Sets the output off phase angle.
OUTP:PHAS:ON
Enables or disables output-on phase control.
OUTP:PHAS:ON:LEV
Sets the output-on phase angle.

PROGram Command
PCR-WE Interface Manual
11
OUTP:PON
Sets the output state that the PCR-WE will be in when the power is turned on.
OUTP:PROT:CLE
Clears alarms.
OUTP:PROT:WDOG
Enables or disables the communication monitoring (WATCHDOG) timer.
OUTP:PROT:WDOG:DEL
Sets the delay time of the communication monitoring (WATCHDOG) timer.
OUTP:SST
Enables or disables soft start.
OUTP:SST:FALL
Enables or disables soft stop.
OUTP:SST:TIME
Sets the soft start rise time.
OUTP:SST:TIME:FALL
Sets the soft stop fall time.
PROGram Command
PROG:CLE
Sets all the steps in the sequence to their default values.
デフォルトになるまでには、約 3秒かかります。
PROG:EDIT
Collectively sets a sequence step (frequency, voltage, signal change, step time, waveform
bank, status output, trigger I/O, output).
PROG:EDIT:FUNC:BANK
Sets the waveform bank number of the sequence step.
PROG:EDIT:JUMP
Configures the jump settings of a sequence step.
PROG:EDIT:IMP
Sets whether to set the output impedance in the sequence step.

KIKUSUI Electronics Corp. 12
PROG:EDIT:IMP:REAC
Sets the reactance component of the output impedance used in the sequence step.
PROG:EDIT:IMP:REAL
Sets the resistance component of the output impedance used in the sequence step.
PROG:EDIT:PHAS:RAMP
Sets the phase signal change of a sequence step.
PROG:EDIT:PHAS:STAR
Sets the starting phase angle and whether to suddenly change the phase of the sequence
step.
PROG:EDIT:PHAS:STOP
Sets the ending phase angle of the sequence step.
PROG:EDIT:PHAS:UOFF
Sets the U phase offset phase angle of a sequence step.
PROG:EDIT:PHAS:UV
Sets the U-V phase difference of the sequence step.
PROG:EDIT:PHAS:UW
Sets the U-W phase difference of the sequence step.
PROG:EDIT:VOLT
Sets the unbalanced AC voltage of the sequence step
PROG:EDIT:VOLT:OFFS
Sets the unbalanced DC voltage of the sequence step
PROG:EXEC
Queries the sequence execution state.
PROG:LOOP
Sets the sequence repetition count.
PROG:STAT
Changes the execution state of the sequence.
PROG:STEP:END
Sets the sequence ending step number
PROG:STEP:STAR
Sets the sequence starting step number

SENSe Command
PCR-WE Interface Manual
13
SENSe Command
SENS:AVER:COUN
Sets the moving average count for current measurement.
SENS:CURR:HOLD:CLE
Clears the hold time of the peak current..
SENS:CURR:HOLD:TIME
Sets the hold time of the peak current.
SENS:VOLT:AVER:COUN
Sets the moving average count for voltage measurement.
SENS:VOLT:HOLD:CLE
Clears the hold time of the peak voltage.
SENS:VOLT:HOLD:TIME
Sets the hold time of the peak voltage.
SIMulation Command
SIM:EXEC
Queries the execution status of power line abnormality simulations.
SIM:POL
Sets the voltage regulation polarity of power line abnormality simulations.
SIM:REP:COUN
Sets the number of repetitions of power line abnormality simulations.
SIM:STAT
Executes or stops a power line abnormality simulation.
SIM:T1:PHAS
Sets the voltage regulation starting phase of power line abnormality simulations.
SIM:T1:PHAS:STAT
Selects whether the voltage regulation start of power line abnormality simulations will be
set in terms of time or in terms of phase.
SIM:T1:TIME
Sets the voltage regulation starting time of power line abnormality simulations.

KIKUSUI Electronics Corp. 14
SIM:T2:TIME
Sets slope time 1 of power line abnormality simulations.
SIM:T3:TIME
Sets the voltage regulation time of power line abnormality simulations.
SIM:T3:VOLT
Sets the regulated voltage of power line abnormality simulations.
SIM:T4:TIME
Sets slope time 2 of power line abnormality simulations.
SIM:T5:CYCL
Sets the number of return cycles of power line abnormality simulations.
SIM:T5:CYCL:STAT
Selects whether the period that the PCR-WE remains in the returned state is configured in
terms of time or in terms of cycles for power line abnormality simulations.
SIM:T5:TIME
Sets the return time of power line abnormality simulations.
[SOURce:]CURRent Command
CURR
Sets the upper limit of the output current.
CURR:PEAK
Sets the output current peak limit of the positive electric potential
CURR:PEAK:LOW
Sets the output current peak limit of the negative electric potential
CURR:PROT:STAT
Sets how the PCR-WE acts when the current limit is exceeded.
CURR:PROT:TRIP:DEL
Sets the time that must elapse before the output is turned off when the current limit is
exceeded

[SOURce:]FREQuency Command
PCR-WE Interface Manual
15
[SOURce:]FREQuency Command
FREQ
Sets the frequency.
FREQ:LIM:LOW
Sets the lower frequency limit.
FREQ:LIM:UPP
Sets the upper frequency limit.
FREQ:SYNC
Sets the sync function.
FREQ:SYNC:MODE
Sets the input sync signal of the sync function.
FREQ:SYNC:PHAS:DEL
Sets the synchronization delay phase angle of the synchronization function.
FREQ:TRIG
Sets the frequency to change to when INIT/INIT:TRAN or a software trigger is sent.
[SOURce:]FUNCtion Command
FUNC:BANK
Specifies the number of the waveform bank that you want to execute.
[SOURce:]VOLTage Command
VOLT
Set the AC voltage.
VOLT:COMP:MODE
Sets the compensation (voltage compensation).
VOLT:COMP:RADJ
Sets the voltage to correct with regulation adjustment.
VOLT:COMP:SOFT:CONT
Set the soft sensing control target.

KIKUSUI Electronics Corp. 16
VOLT:COMP:SOFT:TERM
Set the sensing point.
VOLT:EXT:INP:EXTDC:ADJ:GAIN
Sets the gain for when the input waveform is amplified using an external analog signal.
VOLT:EXT:INP:EXTDC:ADJ:OFFS
Sets the offset for when the input waveform is amplified using an external analog signal.
VOLT:EXT:INP:EXTDC:APER
Sets the measurement time for when the input waveform is amplified using an external
analog signal.
VOLT:EXT:INP:EXTDC:SIGN:POL
Sets the signal polarity of each channel for when the input waveform is amplified using an
external analog signal.
VOLT:EXT:INP:EXTDC:SIGN:SOUR
Sets the signal source for when the input waveform is amplified using an external analog
signal.
VOLT:EXT:INP:FUNC:MODE
Selects the parameter to control with the external analog signal.
VOLT:EXT:INP:VPR:ADJ:GAIN
Sets the gain for when varying the voltage or frequency with the external analog signal.
VOLT:EXT:INP:VPR:ADJ:OFFS
Sets the offset for when varying the voltage or frequency with the external analog signal.
VOLT:EXT:INP:VPR:MAP
Sets the channel configuration for when varying the voltage or frequency with the external
analog signal.
VOLT:EXT:INP:VPR:STAT
Turns on or off the output of each channel for when varying the voltage or frequency with
the external analog signal.
VOLT:LIM:LOW
Sets the lower AC voltage limit.
VOLT:LIM:UPP
Sets the upper AC voltage limit.

[SOURce:]VOLTage Command
PCR-WE Interface Manual
17
VOLT:LTL
Sets the line AC voltage.
VOLT:OFFS
Sets the DC voltage.
VOLT:OFFS:LIM:LOW
Sets the lower DC voltage limit.
VOLT:OFFS:LIM:UPP
Sets the upper DC voltage limit.
VOLT:OFFS:LTL
Sets the line DC voltage.
VOLT:OFFS:TRIG
Sets the DC voltage to change to when INIT:TRAN or a software trigger is sent.
VOLT:PROT:LOW
Sets the UVP value.
VOLT:PROT:PEAK:LOW
Sets the negative peak OVP value.
VOLT:PROT:PEAK:UPP
Sets the positive peak OVP value.
VOLT:PROT:LOW:STAT
Enables/disables UVP.
VOLT:PROT:UPP
Sets the OVP (rms) value.
VOLT:RANG
Sets the voltage range.
VOLT:RESP
Sets the response speed.
VOLT:TRIG
Sets the AC voltage to change to when INIT:TRAN or a software trigger is sent.

KIKUSUI Electronics Corp. 18
STATus Command
STAT:OPER
Queries the event of the OPERation status register.
STAT:OPER:COND
Queries the condition of the OPERation status register.
STAT:OPER:ENAB
Sets the enable register of the OPERation status register.
STAT:OPER:NTR
Sets the negative transition filter of the OPERation status register.
STAT:OPER:PTR
Sets the positive transition filter of the OPERation status register.
STAT:OPER:INST
Queries the event of the OPERation:INSTrument subregister.
STAT:OPER:INST:COND
Queries the condition of the OPERation:INSTrument subregister.
STAT:OPER:INST:ENAB
Sets the enable register of the OPERation:INSTrument subregister.
STAT:OPER:INST:NTR
Sets the negative transition filter of the OPERation:INSTrument subregister.
STAT:OPER:INST:PTR
Sets the positive transition filter of the OPERation:INSTrument subregister.
STAT:OPER:INST:ISUM{1|2|3}
Queries the event of the OPERation:INSTrument:ISUMmary{1|2|3} subregister.
STAT:OPER:INST:ISUM{1|2|3}:COND
Queries the condition of the OPERation:INSTrument:ISUMmary{1|2|3} subregister.
STAT:OPER:INST:ISUM{1|2|3}:ENAB
Sets the enable register of the OPERation:INSTrument:ISUMmary{1|2|3} subregister.
STAT:OPER:INST:ISUM{1|2|3}:NTR
Sets the negative transition filter of the OPERation:INSTrument:ISUMmary{1|2|3}
subregister.

STATus Command
PCR-WE Interface Manual
19
STAT:OPER:INST:ISUM{1|2|3}:PTR
Sets the positive transition filter of the OPERation:INSTrument:ISUMmary{1|2|3}
subregister.
STAT:QUES
Queries the event of the QUEStionable status register.
STAT:QUES:COND
Queries the condition of the QUEStionable status register.
STAT:QUES:ENAB
Sets the enable register of the QUEStionable status register.
STAT:QUES:NTR
Sets the negative transition filter of the QUEStionable status register.
STAT:QUES:PTR
Sets the positive transition filter of the QUEStionable status register.
STAT:QUES:INST
Queries the event of the QUEStionable:INSTrument subregister.
STAT:QUES:INST:COND
Queries the condition of the QUEStionable:INSTrument subregister.
STAT:QUES:INST:ENAB
Sets the enable register of the QUEStionable:INSTrument subregister.
STAT:QUES:INST:NTR
Sets the negative transition filter of the QUEStionable:INSTrument subregister.
STAT:QUES:INST:PTR
Sets the positive transition filter of the QUEStionable:INSTrument subregister.
STAT:QUES:INST:ISUM{1|2|3}
Queries the event of the QUEStionable:INSTrument:ISUMmary{1|2|3} subregister.
STAT:QUES:INST:ISUM{1|2|3}:COND
Queries the condition of the QUEStionable:INSTrument:ISUMmary{1|2|3} subregister.
STAT:QUES:INST:ISUM{1|2|3}:ENAB
Sets the enable register of the QUEStionable:INSTrument:ISUMmary{1|2|3} subregister.

KIKUSUI Electronics Corp. 20
STAT:QUES:INST:ISUM{1|2|3}:NTR
Sets the negative transition filter of the QUEStionable:INSTrument:ISUMmary{1|2|3}
subregister.
STAT:QUES:INST:ISUM{1|2|3}:PTR
Sets the positive transition filter of the QUEStionable:INSTrument:ISUMmary{1|2|3}
subregister.
STAT:PRES
Resets the ENABle, PTRansition, and NTRansition filter registers of all status registers
(including sub registers) to their default values.
SYSTem Command
SYST:COMM:RLST
Sets the product to remote or local mode.
SYST:CONF:ACC
Enables/disables AC coupling.
SYST:CONF:ADJ:VOLT:FINE
Sets the output voltage offset.
SYST:CONF:ADJ:VOLT:TERM:MODE
Set whether the sensing function is enabled or disabled for the voltage offset setting.
SYST:CONF:FORM:FRAM
Queries the number of units operating in parallel.
SYST:CONF:FORM:FRAM:INFO
Queries the information about the specified PCR-WE.
SYST:CONF:FORM:PMOD
Queries the number of power modules in the specified PCR-WE.
SYST:CONF:FORM:PMOD:INFO
Queries the information about the specified power module.
SYST:CONF:FORM:PSAV:MAX
Sets the maximum expected power of the power-saving function.
SYST:CONF:FORM:PSAV:MOD
Sets all power modules to run using the power-saving function.