Knight Cubit Tambour User manual

knightgroup.co.nz
Tools Required: Powered Screwdriver
Assembly Instructions
Cubit Tambour

Assembly Instructions
knightgroup.co.nz
Recommended
2 Person Assembly
Thank you for purchasing Knight product, please carefully read the assembly instructions prior to installment to gain a complete
understanding of the product. It provides you with important information about the safety, use, installation and maintenance.
WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS REGARDING
THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.
SAFETY
• The product must be used in a safe manner. Inappropriate use may cause damage to the product and/or cause bodily harm to
the user or persons nearby.
• Don’t locate furniture in direct sunlight or near air-conditioning inlet or heating radiator.
• Don’t put high-temperature or frozen objects on furniture.
• Safely carry product to location of assembly.
• Retain this operation manual and pass it on to any future owner.
SET UP AND INSTALLATION
• Assemble the product according to the assembly instructions.
• To prevent possible scratches or damage, assemble the product on a soft surface such as a blanket, carpet or packaging.
• Place the product a safe distance from window frames, radiators, furniture etc. so that persons cannot become trapped.
It is recommended that this product is assembled by 2 people.
Any questions contact Knight on 0800 143 143
Due to continuous improvement of our products, our assembly instructions may not be in complete accordance with the product
and we apologise in advance.
Cubit Tambour

Assembly Instructions
knightgroup.co.nz
Parts
Item Description Quantity
ATop Panel 1
XLeft Side Panel (Outer) 1
X1 Left Side Panel (Inner) 1
ZRight Side Panel (Outer) 1
Z1 Right Side Panel (Inner) 1
DBack Panel (Outer) 1
D1 Back Panel (Inner) 1
GBottom Panel 1
OBatten 2
EMoveable Shelf 2
BRoller Door 2
Cubit Tambour
The turning direction
of attaching
Incorrect Correct
A
X
O
O
B
Z1
Z
D1
D
X1
E
E
G

Assembly Instructions
knightgroup.co.nz
Item Description Quantity
c1 6x35 Cam Bolt 44
d1 8x30 Dowel Pin 56
c2 Cam Sticker 44
p1 Shelf Pin 10
s1 4x25 Screw 12
m2 Metal Feet 4
s20 6x60 Fix Bolt 4
Parts
c1 6x35 Cam Bolt
s20 6x60 Fix Bolt
d1 8x30 Dowel Pin c2 Cam Sticker s1 4x25 Screw p1 Shelf Pin
m2 Metal Feet
Cam
(pre-installed)
Cubit Tambour

Page 1
Assembly Instructions
knightgroup.co.nz
Step 1
Page 1
Assembly Instructions
Cubit Tambour
Preparation for top panel A, bottom panel G, vertical O, left side panel X, X1, right side panel Z, Z1, back
panels D, D1.
1. Insert cams bolts (c1) and dowel pins (d1) into panels A, G, X, X1, Z and Z1 as illustrated above.
2. Insert dowel pins (d1) into panel D, D1, O as illustrated above.
A
G
X
X1
Z
Z1
O
D1
d1 d1
d1
d1 d1
d1
d1
d1
d1
d1
d1
d1
d1
d1
d1
d1
d1
d1
D
c1
c1
c1
c1
c1
c1
x2
TOP
TOP
TOP
Cams
Screws
Screws
Cams
TOP
TOP
TOP
BOTTOM
BOTTOM
BOTTOM
BOTTOM
BOTTOM
BOTTOM

Page 2
Assembly Instructions
knightgroup.co.nz
Page 2
Assembly Instructions
Cubit Tambour
Outer panel assembly - Back panel D, left side panel X, right side panel Z and batten O (Assemble with the top
of back panel D pointing towards the floor). Insert cam bolts (c1) on panel X and Z into cams on panels D, O and
tighten in a clockwise direction.
Step 2
X
O
O
Z
D
TOP
BOTTOM

Page 3
Assembly Instructions
knightgroup.co.nz
Page 3
Assembly Instructions
Step 3
Inner panel assembly - Back panel D1, left side panel X1, right side panel Z1. (Assemble with the top of back panel
D1 pointing towards the floor). Insert cam bolts (c1) on panel X1 and Z1 into cams on panels D1 and tighten in a
clockwise direction.
Cubit Tambour
Z1
X1
D1
TOP
BOTTOM

Page 4
Assembly Instructions
knightgroup.co.nz
Cubit Tambour
Step 4
Z
O
O
Z1 D1 X1
X
D
A
Top panel A assembly - Place top panel A on floor with tracking facing upwards. Insert cam bolts (c1) on panel
A into cams on panels X, Z, D, O and tighten in a clockwise direction, repeat above assembly for the assembled
inner panels X1, Z1 and D1.
Adjust screws on the inner side of panels X and Z via the through holes on panels X1 and Z1, align the hole in the
screw with the vertical hole in the end of the panel to allow for the fix bolts to tighten when assembling bottom
panel G in Step 6.
TOP
BOTTOM

Page 5
Assembly Instructions
knightgroup.co.nz
Page 5
Assembly Instructions
Cubit Tambour
Step 5
Door assembly - Insert and slide door sections onto main door panel with handle, repeat for second door.
Place roller doors into groove of top panel A making sure all sections are sliding within the groove.
10PCS
10PCS
Z
O
O
D1
X1
X
A
B
B

Page 6
Assembly Instructions
knightgroup.co.nz
Page 6
Assembly Instructions
Cubit Tambour
Step 6
Bottom panel G assembly - Insert cam bolts (c1) on panel G into cams on panels X, X1, D, D1, Z, Z1 & O (making
sure tracking in panel G aligns with the bottom or the roller door), then tighten cams in a clockwise direction.
Fix bottom panel G on to panel X and Z with fix bolts (s20). Attach metal feet to panel G with provided screws (s1).
Z
D1
G
s20
s1
B

Page 7
Assembly Instructions
knightgroup.co.nz
Page 7
Assembly Instructions
Step 7
Turn tambour over in to upright position.
Moveable shelf E assembly - Insert shelf pins (p1) into panels D1, X1, and Z1 at desired shelf heights, place panel E
on top of shelf pins (p1). Place cam stickers (c2) over the top of the cams.
Cubit Tambour
A
X
Z1
E
E
D1
G
O
O
c2
p1

Page 8
Assembly Instructions
knightgroup.co.nz
Page 8
Assembly Instructions
Complete
Cubit Tambour