Knight Ergoplan Credenza User manual

knightgroup.co.nz
Tools Required: Powered Screwdriver
Assembly Instructions
Ergoplan Credenza

Assembly Instructions
knightgroup.co.nz
Recommended
2 Person Assembly
Thank you for purchasing Knight product, please carefully read the assembly instructions prior to installment to gain a complete
understanding of the product. It provides you with important information about the safety, use, installation and maintenance.
WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS REGARDING
THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.
SAFETY
• The product must be used in a safe manner. Inappropriate use may cause damage to the product and/or cause bodily harm to
the user or persons nearby.
• Don’t locate furniture in direct sunlight or near air-conditioning inlet or heating radiator.
• Don’t put high-temperature or frozen objects on furniture.
• Safely carry product to location of assembly.
• Retain this operation manual and pass it on to any future owner.
SET UP AND INSTALLATION
• Assemble the product according to the assembly instructions.
• To prevent possible scratches or damage, assemble the product on a soft surface such as a blanket, carpet or packaging.
• Place the product a safe distance from window frames, radiators, furniture etc. so that persons cannot become trapped.
It is recommended that this product is assembled by 2 people.
Any questions contact Knight on 0800 143 143
Due to continuous improvement of our products, our assembly instructions may not be in complete accordance with the product
and we apologise in advance.
Ergoplan Credenza

Assembly Instructions
knightgroup.co.nz
Ergoplan Credenza
Parts
Item Description Quantity
ATop Panel 1
XLeft side Panel 1
ZRight side Panel 1
DBack Panel 1
GBottom Panel 1
V1 Left Door Panel 1
V2 Right Door Panel 1
EMoveable Shelf 2
YVertical Panel 1

Assembly Instructions
knightgroup.co.nz
Ergoplan Credenza
Item Description Quantity
c1 6x35 Cam Bolt 24
d1 8x30 Dowel Pin 24
c2 Cam Sticker 24
p1 Shelf Pin 8
s7 4x22 Fix Bolt 4
h3 Handle 2
s1 3.5x15 Screw 10
b1 Bracket 2
c6 Foot 6
s2 3.5x35 Screw 6
k3 Lock 1
Parts
c1 6x35 Cam Bolt
c6 Foot
d1 8x30 Dowel Pin
s2 3.5x35 Screw
c2 Cam Sticker
s1 3.5x15 Screw
p1 Shelf Pin
b1 Bracket k3 Lock
h3 Handle
Cam
(pre-installed)
Door Catch
(pre-installed)
Door Castor
(pre-installed)
s7 4x22 Fix Bolt

Assembly Instructions
knightgroup.co.nz
Step 1
Page 1
Assembly Instructions
Ergoplan Credenza
Preparation for credenza top panel A, credenza bottom panel G, left side panel X, right side panel Z, door
panel V1 and V2.
1. Insert cam bolt (c1) and dowel pins (d1) into panel A, G, X and Z as illustrated above.
2. Assemble handle (h3) with fix bolts (s7) on door panel V1 and V2 as illustrated above.
3. Assemble the lock (k3) with screws (s1) on door panels V2 as illustrated above.
4. Assemble feet (c6) with screws (s2) on bottom panel G as illustrated above.
c6
s1
d1
c1
k3
s7
h3
s2
Door Castor
(Pre-installed)
Door Catch
(Pre-installed)

Assembly Instructions
knightgroup.co.nz
Page 2
Assembly Instructions
Step 3
Insert cam bolt (c1) on panel G into cams on panel X, Z, Y and D and fully tighten. Then place cam stickers (c2) on
the top of cams.
Insert cam bolt (c1) on panels X, Z into cams on panel D and fully tighten. Fix cams on panel Y, D, X and Z into cam
bolts (c1) on panel A and fully tighten.
Step 2
Ergoplan Credenza
s1
c2
b1

Assembly Instructions
knightgroup.co.nz
Page 3
Assembly Instructions
Step 5
Slightly tilt door V1 towards you and place door castors in bottom tracking closest to inner of credenza. As you
move door back into upright position hold down the door catch buttons to secure door in place on the top
tracking. Repeat for door V2 in the outer track closest to you.
Insert shelf pins (p1) into panel X, Z and Y, put the two panels E on the top of shelf pins (p1) as illustrated below.
Step 4
Ergoplan Credenza
p1
Door catch
(Pre-installed)

Assembly Instructions
knightgroup.co.nz
Page 4
Assembly Instructions
Complete
Ergoplan Credenza