Kohler OVE Vanity Lavatory K-19950T User manual

OVE
INSTALLATION INSTRUCTIONS
VANITY LAVATORY
K-19950T, K-19951T
-1-
1072204-T01-A
, 2007
Copyright Kohler China Ltd., 2007
·
·
·
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
All information in these instructions are based the latest
product information available at the time of publication.
Kohler China reserves the right to make changes in
product characteristics, packaging, or availability at any
time without notice.
Make sure that the wall and floor are square
and plumb to ensure proper installation.
IMPORTANT:
·
·
·
ORDERING INFORMATION
OVE Vanity Lavatory ..........................................K-19950T
Includes Mounting Kits .....................................1034692
OVE Vanity Lavatory ..........................................K-19951T
Includes Mounting Kits .....................................1034692
..................................................K-19950T
........................................................1034692
..................................................K-19951T
........................................................1034692
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
·
·
·
·
·
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
·
·
·
·
·
·
·
6mm
14mm
528137

ROUGHING-IN DIMENSIONS
ROUGHING-IN DIMENSIONS
UNIT: mm
:
Fig.#1
1
K-19951T
140
216
68
35
462
45
925
605
130
505
344
45
440
1195
440
150
K-19950T
150 140
216
280
35
130
505
344
440
895
45
68
462
Install the Basin
Note! The lavatory tops can be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
!
!(
)
!
-2-
1072204-T01-A
·
76mm
·Rough-in the supplies and the drain piping.
The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
NOTE:
·
·
10mm
()
, 55-
60mm
1. 2 3
2.
·
·
Drill two 10mm hanger bolt holes at the marks on the wall.
The nylon anchors is needed for concrete wall (supplied).
Mount hanger bolts to the wall so approximately 55-60mm
of each bolt remains exposed.
1. Height dimensions marked in fig. 2 and fig. 3 could
be adjusted per your requirement.
2. Other fastening devices of sufficient size and
strength may also be used.
NOTE:

Fig.#2
2
-3-
280mm
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
818mm
80mm
Single Vanity Top
Fig.#3
3
Double Vanity Top
925mm
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
825mm
80mm
1072204-T01-A
·
·Install the faucet and drain to the lavatory according to the
manufacture's instructions.
·
·
·
·
·Carefully place the lavatory against the wall, so the
hanger bolts extend through the lavatory holes.
·
·
·
Level the lavatory.
Install the cap nuts and washers, and tighten until snug.
Do not
overtighten the cap nuts.Overtightening may cause
damage to the product.
Clean the lavatory top.
CAUTION: Risk of product damage.
·· Put the sealant around the back wall attached surface of
the lav evenly.

Apply Silicone sealant
along this face
Washer Nut
Offset Nut
Fig.#4
4
-4-
1.
2.
3.
4.
Install the Plumbing
1. Install the drain in accordance with the manufacturer s
instructions.
Make sure a watertight seal exists on all
basin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supply
connections for leaks.
4. Run water into the basin, and check the drain connections
for leaks.
Caution!
Caution!
,
Fig.#5
5
1072204-T01-A

IMPORTANT CONSUMER INFORMATION
IMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
DO NOT USE ABRASIVES
Caution! Risk of product damage.
Many cleaners contain abrasive and chemical substances,
and should not be used for cleaning stainless steel, enamel,
plated or plastic fittings.
These finishes should be cleaned using a mild washing up
detergent or soap solution, rinsed and then wiped dry with a
soft clean cloth.
-5-
1072204-T01-A