Kohler K-37469T User manual

13-1 528437
INSTALLATION INSTRUCTIONS
8mm
PIVOT DOOR,SCREEN, 1 D1P, 8mm
K-37469T
STANCE
-1-
, 2010
Copyright Kohler China Ltd., 2010
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
3
(
) 50~80mm
3mm/m
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should fall
within the range of 50~80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won t take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
1160390-T01-A

-2-
ROUGHING-IN
Unit: mm
BH
SKU
K-37469T 800-1600 1850-2000
H
B
800-820-2628
IMPORTANT
800-820-2628
The wall channel for the side panel is delivered to the
door assembly. Remove the panel wall channel before
installing the door, but do not remove the transit blocks.
Before installation check that all components are
correctly supplied.
If any parts are missing please ring the helpline.
PARTS IDENTIFICATIONPARTS IDENTIFICATION
1160390-T01-A

-3-
Wall Frame
Wall Jamb
Side Panel
Magnetic Seal
Bottom Frame
Top Frame
Door Glass
Insert Edg
Side Seal
Cover Cap
Frame Cap, Bottom
X2
Frame Cap, Top
X4
Pivot Caver, Bottom
Pivot Caver, Top
Glass Shelf
X1
Handle Assy.
Pivot Pin
X2
4mm Allen Key
4mm
X6
X10
X6X2
Cover
X6
·
·
·
·
·
·
·
·
·
·
·
·
·
Phillips Screwdriver
Pencil
Caulk Gun
Measuring Tape
Safety Glasses
Center Punch
Hammer
Knife
Masonry Drill & 6mm Drilll Bit
Level
Drop Cloth
Materials Required
Tape
Silicone Sealant
Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
6mm
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
1160390-T01-A

-4-
INSTALLATION
STEP
1
STEP
2
The wall jamb
be kept
vertical.
must
The wall jamb
be kept
vertical.
must
0mm
6mm
6mm
0mm
Fix one side of the wall jamb. Line on the other side. Drill a pivot hole, then insert
wall anchor.
STEP
4
STEP
3
Fix both top and bottom frame to the side wall frame. Insert another wall jamb into the side wall frame.
Frames raised
shall face outside.
Note:
The side
of the wall
frame with hole
shall face
inside.
Note:
1160390-T01-A

-5-
STEP
6
STEP
5
Insert the whole set of the frame into the wall jamb. Across through the frame with screw, then fix the wall
jamb.
Please first insert the glass into the top frame and then into the bottom frame.
Please insert the glass in the correct direction: the
end with the hole shall be close to the top frame
and the labeled side with arrows on the label shall
be against the wall.
STEP
7
1160390-T01-A

-6-
STEP
8
Insert the glass into the wall frame.
STEP
9
Lift the door into place.
Insert the pin into the base and then insert the glass door.
IMPORTANT: Ensure the door is fully supported
at all times.
Note: Please make sure
that there should be inserts
with correct directions at
both these two places.
1160390-T01-A

-7-
STEP
10
STEP
11
Remove the pivot pin assembly on top. Insert the pivot pin both into the base and the body.
Then tighten the glass and the pivot pin assembly.
Note: The pivot
pin assembly
should be
vertical after
being tightened.
STEP
13
STEP
12
Push the wall frames at both sides to make the gap even between the
glass and the top and bottom frames.
Install the handle.
1160390-T01-A

-8-
STEP
14
Tighten the wall jamb and the wall frames.
STEP
15
Install the base of the glass bracket.
Note: Ensure the accessory is
positioned in a horizontal way.
6mm
Note: Ensure the
accessory is positioned
in a horizontal way.
STEP
16
Line, then fix the bracket base.
STEP
17
Fix the glass bracket.
1160390-T01-A

STEP
20
Install the edge strip to fix the side panel.
STEP
19
Fix the glass and the top frame. Then insert the side
seal into the wall frame.
STEP
18
Fix the magnetic strips onto the door glass and the
.
side panel
When the door is closed the magnetic
strips should touch along their length.
STEP
21
Insert the cover seal to the top frame.
-9-
1160390-T01-A

-10-
STEP
22
Fix the side seal onto the door glass. Insert the cover
seal to the wall frame.
STEP
23
Insert the bottom seal to the door glass.
STEP
24
Install the pivot pin and other cover caps.
STEP
25
Install the frame cap of top and bottom frame.
1160390-T01-A