Kohler Mira Showers Elevate 2.1814.107 User manual

11544819-W2-A
Elevate Bathscreens
These instructions must be left with the user
Installation Guide

2
1544819-W2-A

31544819-W2-A
Thank you for purchasing a quality Mira product. To enjoy the full potential of your new
product, please take time to read this guide thoroughly, having done so, keep it handy for
future reference.
The following pages aim to provide comprehensive installation instructions, plus advice on
how to care and maintain your product.
Safety Information
1.
wires.
2. We strongly recommend that all glass panels are moved by a minimum of two people
and that any protective packaging along the glass edges is kept in place for as long as
possible to prevent damage before installation.
3. Wear protective footwear when lifting panels.
4. Wear safety glasses when drilling.
GENERAL INFORMATION
INTRODUCTION
Before Fitting the Bathscreen
1. Ensure the Bath is level and that there is a complete silicone seal between the bath and
2.
of a bath.
3. Ensure water is not directed at the bathscreen. This could result in water spraying
outside of the showering space.
4. Ensure the size of bathscreen is suitable for the installation. Tempered safety glass
cannot be cut.
5. Ensure nothing can impact the bathscreen during operation.
General
1. Read all of these instructions and retain this guide for later use.
2. Pass on this guide in the event of change of ownership of the installation site.
3. Follow all warnings, cautions and instructions contained in this guide.
4.

4
1544819-W2-A
TOOLS REQUIRED
3.0 mm HSS
6.0 mm
For domestic installations
starts from date of purchase.
For non-domestic installations, we guarantee the product against any defect in materials
or workmanship for a period of one year from the date of purchase.
For terms and conditions refer to the back cover of this guide.
Domestic 
Light Commercial 
Heavy Commercial 
Healthcare 
RECOMMENDED USAGE
GUARANTEE
When Fitting the Bathscreen
1.
surface. Failure to do so will result in an unsatisfactory seal, which may cause property
damage.
Use of the Bathscreen
1.
outside of the bathscreen.
2. In certain circumstances such as cleaning, water sprayed directly at the seals may
escape outside of the bathscreen.
X 4

51544819-W2-A
that all of the parts are included.
PACK CONTENTS
Single Panel Round/Square
Documentation
1 x Guarantee Registration Document
Note: Wall plugs are not supplied.
1 x Installation Manual
Square Round
OR
X 4
X 1 X 1
X 1
X 1
X 4
X 4
X 4

Note: Wall plugs are not supplied.
Square
X 4
X 1
6
1544819-W2-A
PACK CONTENTS
Documentation
1 x Guarantee Registration Document
1 x Installation Manual
Static Panel
X 4
X 4
X 4

71544819-W2-A
INSTALLATION
1
Note! Tile down on top of the bath and seal around the edge. Make sure the
bath is level across all axis.
± 0 mm
± 0 mm

8
1544819-W2-A
2Single Panel Round/Square 2
10mm
x4
x4
x4
x4
(Not supplied)
Note: Choose wall plugs
suitable for your wall type.
Wall plugs should be
without collar.
Ø6mm
± 0 mm
(a) Position the wall channel on the wall. Using a spirit level make sure that it is upright.
(b)
(c) Drill with a 6 mm masonry bit (not supplied) and plug using the wall plugs (not supplied).
(d)
(e) Apply silicone sealant according to the manufacturers instructions along the length of
the wall and at the bottom of the wall channel.
(f)
6.0 mm
Inside

91544819-W2-A
3
Push the horizontal seal onto the bottom of the glass, the cut out end going towards
the wall.
Ensure the seal is correctly engaged into the pivot block.
Install horizontal seal

Apply a small amount of silicone sealant at the bottom of the
wall channel before you install the bathscreen.
10
1544819-W2-A
4
Note: The horizontal seal should accommodate most baths but many bath rims are
uneven, you can adjust the seal to give an even compression along the bath to
eliminate any gaps.
Seal
compression
should be as
illustrated