Kohler NEW PURIST K-701575T User manual

1361033-T01-A
-1-
BEFORE YOU BEGIN 安装之前
© Copyright Kohler China Investment Co., Ltd. 2018
© 版权为科勒（中国）投资有限公司所有 2018
ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINGYE ROAD, ZHONGSHAN TORCH
DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437
中山科勒卫浴有限公司 广东省中山市中山火炬开发区兴业路 13-1 号邮编：528437
• 说明书中所有的资料是按最新出版的产品资料编写而成。
科勒中国有限公司保留任何时候无须通知即可改变产品特
性、包装或产品可供类型的权利。
• 说明书包括重要的安装、清洁及保养方面的内容，请把这
些资料交给用户阅读，保管。
• 确保在安装淋浴房之前已经完整正确地安装了浴室和完工
墙面材料。淋浴区墙地面应做防水处理，并不得布置有电
器开关、插座。确保地面排水通畅。
• 在进行淋浴房安装之前，请拿出、排列并确认所有的零部
件。请参考第 2 页上所示的分解图。
• 对尺寸与本标准产品不同的定制淋浴房，参照本说明书进
行安装。
• 本产品符合 QB 2584-2007。
• All information is based on the latest product information
available at the time of publication. Kohler China Ltd.
reserves the right to make changes in product
characteristics, packaging, or availability at any time
without notice.
• These instructions contain important care, cleaning, and
warranty information-please leave these instructions for
the consumer.
• Make sure that the bath and the finished wall material are
completely and correctly installed prior to installing your
shower door. Prepare waterproof layer to wall and floor of
the showering area. It is not allowed for any presence of
electric switches and sockets. Make sure the floor drain
runs smoothly.
• Before starting the door installation, lay out and identify all
the parts. Use the exploded view illustrated on page 2 for
reference.
• For the installation method of customized shower with
different dimensions, please refer to this instructions.
• The product complies with QB 2584-2007.
警告：可能有人员伤害或者产品损坏的危险。
钢化玻璃不能进行切割，钻孔或硬物敲击。搬移或安装
过程中，小心确保玻璃边、角部位不受撞击，以防爆裂
伤人。
建议：将本产品安装在科勒淋浴盆或挡水条上（需另行购买）。
如自备挡水条，建议顶面宽度尺寸大于 80mm。
重要事项：淋浴房需要安装在平坦垂直的墙面上。墙面的垂直度
推荐在正负 3mm/m 以内。如果超出此范围，科勒公司将不保证
淋浴房的完美使用。
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or knocked by
hard object. Make sure corner area of the glass
refraining from knocking so as to cause personal injury
due to broken glass.
ATTENTION: Please install this door on Kohler receptors or
curbs(Not included). If the curb is not Kohler-branded, please
note its top width should be more than 80mm.
IMPORTANT: The shower door requires a flat vertical
finished wall. The squareness of the wall is recommended no
more than 3 mm/m. KOHLER Company won't take
responsibility of the installation quality.
24hrs
ROUGHING-IN 尺寸图
Unit: mm
单位：毫米
Do not use the enclosure for at least 24 hours.
安装后 24 小时内请勿使用淋浴房。
NEW PURIST 新飘瑞诗
INSTALLATION INSTRUCTIONS
安装说明书
L SHAPE, 1D2P, 10mm
L型，两固一活，10mm 防爆膜玻璃
K-701575T - FM - SHP
SKU B H
K-701575T 1850-2000950-1600
C
250-1100
B
H
C

Tools Required/所需工具
5mm Allen Key
5mm 六角扳手
2.5mm Allen Key
2.5mm 六角扳手
Masonry Drill &
6mm Drill Bit
冲击钻以及
6mm 冲击钻头
Pencil
铅笔
Level
水平仪
Measuring Tape
卷尺
Phillips Screwdriver
十字螺丝刀
Hammer
锤子
Knife
刀片
Caulk Gun
硅胶枪
Safety Goggles
护目镜
1361033-T01-A
-2-
Wall Jamb Clamp Cap, New Purist 新飘瑞诗夹材装饰材X2
Wall Jamb Clamp, New Purist 新飘瑞诗夹材X2
Wall Channel Clamp, New Purist 新飘瑞诗上墙材X2
Bottom Frame Profile, New Purist 新飘瑞诗底横梁
X2
Magnetic Seal, 180°, 10mm 180 度门吸磁条
X1
Side Seal, 10mm, Profile, Hinged Door 侧边胶条X1
Bottom Seal For Purist DR Glass Profile 门底胶条X1
Glass Gripping Seal, Profile, 10mm 固玻压紧胶条 X4
Inserted Seal For Bottom Frame, Purist 底横梁嵌入胶
X2
Hinge Assy, Up, New Purist 新飘瑞诗上铰链组件X1
Hinge Assy, Bottom, New Purist 新飘瑞诗下铰链组件X1
Trolley Wall Body Assy, New Purist 拉杆上墙座组件X1
Panel Glass Trolley Body Assy, New Purist 固玻拉杆夹紧座组件X1
Trolley Flat Tube 10X30 不锈钢扁管X1
Trolley Side Body Assy, New Purist 拉杆侧扇夹紧座组件X1
Composed Handle Assy 450mm, Double 对装柏诗拉手
X1
L Shape Connector Assy, RH, New Purist 新飘瑞诗转角连接座，右开X1
L Shape Connector Assy, LH, New Purist 新飘瑞诗转角连接座，左开X1
Connector Block 塑料压块X10
Cover Cap, New Purist 新飘瑞诗铝材装饰盖X2
CSK Screw ST3.5X6 沉头平尾螺丝 ST3.5X6X10
Screw GB/T 846 ST3.9X12 十字沉头自攻螺钉 ST3.9X12X2
X8 Pan Screw ST3.5X40 圆头螺丝 ST3.5X40
Hollow Wall Anchor, Nylon 膨胀套X8
Screw Cover Cap M6 CSK Grey 螺丝盖帽X2
Screw GB/T 846 ST3.9X12
十字沉头自攻螺钉 ST3.9X12
Cover Cap, New Purist
新飘瑞诗铝材装饰盖
Glass Gripping Seal,
Profile
固玻压紧胶条
Wall Channel Clamp,
New Purist
新飘瑞诗上墙材
Wall Jamb Clamp,
New Purist
新飘瑞诗夹材
Wall Jamb Clamp Cap,
New Purist
新飘瑞诗夹材装饰材
Side Panel Glass,
New Purist
侧固玻璃
Composed Handle Assy
450mm, Double
对装柏诗拉手 450mm
Side Bottom Frame, New Purist
新飘瑞诗侧扇底横梁
Trolley Wall Body
Assy New Purist
拉杆上墙座组件
Trolley Side Body
Assy, New Purist
拉杆侧扇夹紧座组件
Hinge Assy, Up,
New Purist
新飘瑞诗上铰链组件
Trolley Flat Tube
10X30 不锈钢扁管
Panel Glass Trolley
Body Assy, New Purist
固玻拉杆夹紧座组件
Panel Glass
固定玻璃
Connector Block
塑料压块
Bottom Seal
门底胶条
Hinge Assy, Bottom
新飘瑞诗下铰链组件
Bottom Frame Profile,
New Purist
新飘瑞诗底横梁
Inserted Seal For
Bottom Frame
底横梁嵌入胶
Door Glass
门玻璃
Magnetic Seal, 180°, 10mm
180 度门吸磁条
L Shape Connector
Assy, New Purist
新飘瑞诗转角连接座
Side Seal, 10mm
侧边胶条

INSTALLATION 安装
STEP
1
STEP
4
STEP
5
STEP
7
STEP
8
STEP
3
STEP
6
STEP
9
1361033-T01-A
-3-
Connect the two bottom frames with corner blocks.
用转角连接件将两根底横梁连接起来。
Place the weather bar. The installation surface in the
bathroom must be flat.
放置挡水条，淋浴房安装面必须打水平。
Install the bottom frame (20 mm to the edge from the inside).
Fix the wall channels at both ends and make sure that the
channels are aligned to the bottom frame.
安装底横梁（内偏20mm安装），固定两端上墙铝材，请确
保上墙铝材固定时与底横梁对齐。
6mm
STEP
2
Remove the outer cover of the connector assembly.
Insert the side and the hinged glass panels.
先卸开转角座外板，再分别插入侧扇和铰链固玻。
Fix the upper hinge onto the door glass.
将上铰链固定到门玻璃上。
Tighten the screws of the wall channels and clamp the
side panels.
锁紧墙材的螺丝，将固定玻璃夹紧。
Lift the door glass and insert into the bottom hinge.
将门玻璃抬起，插入下铰链里。
Reinstall the outer cover of the connector assembly. Install
the bottom hinges onto the glass panels. Adjust the distance
between the glass panels to about 664 mm.
将转角座外板安装回去，在安装下铰链到固玻，之后调节两
固玻之间的间距尺寸，约为 664mm。
Install the trolley. Adjust the distance between the metal seat
and the two wall channels respectively to 105 mm and 8 mm.
安装拉杆，上墙金属座相对铝材位置为 105mm 和 8mm。
0mm
IMPORTANT:
Tray MUST be level
along front edge.
重要：
底盘必须水平。
IMPORTANT:
Make sure the seals are pre-installed on the wall channels.
重要：安装前确保铝材有预装好胶条。
Aligned
对齐
20mm to
the edge
距边20mm
0mm
0mm
The wall jamb
must be kept
vertical.
上墙材必须垂
直。
The wall jamb
must be kept
vertical.
上墙材必须垂
直。
1.5254
Remove the outer cover of
the connector assembly.
卸开转角座外板。
Reinstall the outer cover.
外盖板装回去。
Tighten the screw.
螺丝需要锁上。
664
Installation hole for
the metal seat.
上墙座钻孔位置。
105
8
*Note: The
decorative cap
needs to be
installed after
the trolley is
installed.
*注意，拉杆安装
完成后，需要扣
上装饰盖。
IMPORTANT:
Ensure the door is fully
supported at all times.
重要：
整个安装过程中，玻璃门必须足
够支撑。
20mm to
the edge
距边20mm

1361033-T01-A
-4-
IMPORTANT: Tighten the backboard of the top hinge and then that of the bottom hinge
when the door glass is closed. The door glass may be adjusted via the following methods.
重要：门玻处于闭合状态时，锁紧上铰链背板，之后锁紧下铰链背板，同时可以通过以下方
式做门玻调节。
Install the decorative frames and then the top decorative caps. Install the handle.
扣上铝材装饰盖材，之后安装顶部两端装饰铝材盖板，再安装拉手。
Install the magnetic strip and the side and bottom waterproof seals.
安装磁条、侧边防水胶条和底边防水胶条。
Apply the silicone sealant.
打防水胶。
Adjust the downward force
via the eccentric sleeve.
通过偏心套调节门玻下坠。
The side and the bottom waterproof
seals shall respectively extend to the
top and the bottom of the hinge.
侧边防水胶条需要通到铰链面，
底部防水胶条需要通到铰链底部。
Adjust the screw
to adjust the
closing force and
the downward
force.
通过调节螺丝调节
关门力和下坠。
The backboard may
be tightened only
when the door glass
is closed.
必须是闭合状态下再
锁紧背板。
Tighten the decorative cap.
锁上装饰铝材盖板。
Install the decorative frame.
扣上铝材装饰盖材。
0mm
STEP
10
STEP
11
STEP
12
STEP
13
Inside
内侧
Inside
内侧
Outside
外侧
Outside
外侧
IMPORTANT: Sealant needs to be applied onto the inside
of the side panel glass.
重要：侧扇固玻内侧需要打胶固定。