Kohler SKYLINE K-705880T-FM-SHP User manual

INSTALLATION INSTRUCTIONS
SLIDING, SCR BYPASS (W STO), 8mm
( ) 8mm
K-705880T-FM-SHP
SLIDING, SCR BYPASS (W STO), 10mm
( ) 10mm
K-81516T-FM-SHP
SKYLINE
-1-
BEFORE YOU BEGINBEFORE YOU BEGIN
3
(
) 80mm
3mm/m
QB 2584-2007
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs(Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
The product complies with QB 2584-2007.
ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINYE ROAD, ZHONGSHAN TORCH
DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437
13-1 528437
©
©
Copyright Kohler China Investment Co., Ltd. 2016
2016
1284345-T01-A

-2-
ROUGHING-IN
Unit: mm
BH
SKU
K-81516T
K-705880T 1400-2050 1850-2000
800-820-2628
IMPORTANT
800-820-2628
Before installation check that all components are
correctly supplied.
If any parts are missing please ring the helpline.
PARTS IDENTIFICATIONPARTS IDENTIFICATION
B
H
H
B
1284345-T01-A

-3-
Wall Jamb,
Skyline Bypass
Door Glass,
Skyline Bypass
Top Roller Assy,
Skyline Bypass
Top Rail, Skyline Bypass
Wall, Skyline Bypass
2D1P Wall Jamb,
Skyline Bypass
2D1P
Insert Seal,
Skyline Bypass
Cover Seal
Panel Glass with Shelf,
Skyline Bypass
Center Post,
Skyline Bypass
Long Bottom Roller Assy,
Skyline Bypass
--
Side Metal Handle,
Skyline
Bottom Rail,
Skyline Bypass
Short Bottom Roller Assy,
Skyline Bypass
--
X1
X1
X1
X2
X1
X1
X6
Top Rail, Skyline Bypass
Bottom Rail, Skyline Bypass
Wall Jamb, Skyline Bypass
Wall, Skyline Bypass
2D1P Wall Jamb, Skyline Bypass 2D1P
Center Post, Skyline Bypass
Insert Seal, Skyline Bypass
X2
X2
X2
X2
X6
X2
X8
X21
X1
X1
X1
Cover Seal
Top Roller Assy, Skyline Bypass
Long Bottom Roller Assy, Skyline Bypass
--
Short Bottom Roller Assy, Skyline Bypass
--
Twist Lock Jamb Moulding, Assy, Skyline Sliding
Side Metal Handle, Skyline
Hollow Wall Anchor, Nylon
Pan Screw ST3.5X40 ST3.5X40
Pan Screw ST3.5X50 ST3.5X50
Screw Key 4mm
Screw Key 2.5mm
1284345-T01-A

·
·
·
·
·
·
·
·
·
·
·
·
·
Phillips Screwdriver
Pencil
Caulk Gun
Measuring Tape
Safety Glasses
Center Punch
Hammer
Knife
Masonry Drill & 6mm Drilll Bit
Level
Drop Cloth
Materials Required
Tape
Silicone Sealant
Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
6mm
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
INSTALLATION
STEP
1
IMPORTANT:
MUSTTray be level
along front edge.
Mark the wall 10mm in from the front edge of the tray.
10mm
0mm
-4-
1284345-T01-A

-5-
STEP
2
Fix the top and bottom frames on the wall jamb.
Before fixing top and bottom frames, make sure of the following: 1. Wall and wall jamb is properly
connected. 2. Seals are properly inserted.
1. 2.
Note:
The wall jamb
be kept vertical.
must
Fix wall jambs. One is fixed on the wall. The other is not fixed on the wall after the holes are drilled. Pay special
attention to both sides of the wall jamb(see magnified pictures below).
(
)
STEP
3
0mm
The wall jamb
be kept vertical.
must
0mm
6mm
Inside
Outside
Seal
Seal
Connector
Connector
Outside
Outside
Inside
Inside
1284345-T01-A

-6-
STEP
5
Adjust the top and bottom frames vertical. The length shall be the same on two sides. Then rotate the lock to fix
wall jamb.
,
Insert the unfixed wall jamb into the frame. Then insert the whole wall jamb and fix the unfixed wall jamb.
STEP
4
The wall jamb
be kept vertical.
must
0mm
Insert the unfixed wall jamb.
XX
Rotate clockwise to
lock.
IMPORTANT:
MUSTTray be level
along front edge.
0mm
1284345-T01-A

STEP
6
Install fixed glass.
Refer to installation instructions of accessories.Note:
Seal
Use U-shaped protective seals on top
and bottom of the fixed glass.
U
-7-
Install door glass.
Install outside door glass first and then inside door glass.Note:
STEP
7
STEP
8
Install top and bottom rollers.
The caps shall be
fixed after the door
glass is installed.
Install bottom roller after the door is
adjusted to a proper position. Fix the cap.
Adjust the height of door glass
by adjusting the screws with
cross screwdriver.
1284345-T01-A

Do not use the enclosure for at least 24 hours.
24
24hrs
-8-
STEP
11
STEP
10
Apply silicone sealant to both sides of the bottom
threshold.
STEP
9
Install and adjust handle.
Install handle.
1284345-T01-A