KOKEN LM-017 User manual

Inspection and
Palpation of Breast
Cancer Training
Model II
LM-017
Instruction Manual
Thank you for purchasing the LM-017 Inspection and Palpation of Breast Cancer Training Model II.
Please read this instruction manual carefully to ensure correct use of the product, and
store it in a safe place for easy access.
KOKEN CO., LTD.
1-4-14 Koraku, Bunkyo-ku, Tokyo 112-0004 JAPAN
URL:http://www.kokenmpc.co.jp
E-mail:[email protected]
C-1-902-2-02-01

1
Handling and Safety Precautions
These precautions should be strictly observed in order to ensure safe,
long-term use of the product.
The following precautions should be observed particularly strictly
1. The model is made using special silicone rubber to simulate the texture of human skin, and may
be damaged if excessive force is applied. We recommend handling the model carefully, in the
same manner as an actual person.
2. Do not use oil pens or paints on the surface, as they may cause permanent staining.
3. Do not wash the model.
Caring for the model after use:
1. If the surface becomes dirty, wipe with moist gauze or another soft cloth using a neutral solvent
diluted with water.
2. To clean more di󱐰cult-to-remove smudges or marks, wipe with moist gauze or another soft cloth
using sterilizing ethanol.
3. Do not use thinners, benzene or similar solvents.
4. To prevent the model from becoming misshapen, always place it in the correct position for
storage.
5. Store the model in a place where it will not be exposed to direct sunlight or UV rays.
1. The contents of this instruction manual are subject to change without notice.
2. This instruction manual may not be reproduced in part or in its entirety without permission.
3. Please contact the manufacturer in the event that any errors or omissions are found in the contents of this
instruction manual.
4. This product should be used only as described in this instruction manual. In particular, the product should not
be used in any way that contravenes the precautions noted in the instruction manual.

2
Table of Contents
1. Outline and Features
2. Components
3. Description of parts
4. Using the model
4-1 Putting on the model
4-2 Caring for the model after use
5. Specications

3
1. Outline and Features
Outline
The incidence of breast cancer is high in women in the prime of life. Chances of recovery are highest
if breast cancer is detected and treated at an early stage. To check for breast cancer, begin by visually
inspecting and palpating the breasts. Breast cancer can appear as a "lump" under the skin or as small
changes in skin tone or evenness. Regular careful self-examination is very important.
If a small skin change is detected, a specialist should immediately be consulted. With early detection
and treatment, there is no need to fear. When creating this model, advice from numerous specialists
was gathered to design a model that is useful for self-examination.
Features
The size and texture of the model is made to be as realistic as possible. Pathological symptoms such
as lumps and skin changes (dimples) may be slightly exaggerated in the model, but the locations
and feel of the lesions are provided with the utmost accuracy.
This not only offers an ideal educational model for health nurses and nursing students, but also
provides an e󱐯ective teaching and training tool for self-examination of breast cancer by the general
public.

4
2. Components
Names of the Components Quantity
① Inspection and Palpation of Breast Cancer Training Model II main body 1
② Baby powder 1
③ Storage case 1
Instruction Manual (this document) 1

5
3. Description of parts
Symptom Number Description
① to ⑤ 80-90% of breast cancers start as a painless lump.
⑤
If the cancer approaches the skin, the skin may become
depressed to form a dimple.
Skin
changes
(dimple)
Lumps

6
4. Using the model
4-1 Putting on the model
1) Open the hook-and-loop fasteners on the upper belt of the model.
Wrap the belt around your neck and fasten the hook-and-loop fasteners in place.
2) Open the hook-and-loop fasteners on the lower belts. Wrap the belt around your torso and
fasten the hook-and-loop fasteners in place.
3) Adjust the length of the belt with the belt length adjuster ring to t the model to your body.
Upper belt
Lower belt
Belt length adjuster ring

7
4.2. Caring for the model after use
1) Wipe away dirt or smudges with gauze or another cloth. If very dirty, wipe with moist gauze
using a neutral solvent diluted with water.
2) Pat the baby powder that came with the kit all over the model.
3) Place the model in the storage case as shown in the picture below. Position the model
in the case so that the neck is facing the handle.
4) Close the lid of the case and store it in a well-ventilated location where it will not be
exposed to direct sunlight or UV rays.
Gauze
Baby powder
Handle

8
5. Specications
Length Width Height Weight
Main body Approx. 22 cm Approx. 30 cm Approx. 11 cm Approx. 1.2 kg
Storage case Approx. 27 cm Approx. 34 cm Approx. 13 cm Approx. 1.2 kg