KOKEN LM-092 User manual

Bronchoscopy
Training Model
LM-092
Instruction Manual
Thank you for purchasing the Bronchoscopy Training Model.
Please read this instruction manual carefully to ensure correct use of the product,
and store it in a safe place for easy access.
KOKEN CO., LTD.
1-4-14 Koraku, Bunkyo-ku, Tokyo 112-0004 JAPAN
URL:http://www.kokenmpc.co.jp
E-mail:[email protected]
C-1-974-1-01-04

10000

1
Handling and Safety Precautions
These precautions should be strictly observed in order to ensure safe,
long-term use of the product.
The following precautions should be observed particularly strictly:
1. This model is made of special silicone. Improper handling may break the model.
2. Do not place any object on the bronchial unit as this may deform the unit.
3. To remove stubborn stains on the model, use gauze or the like that has been soaked with water
or neutral detergent diluted with water. Do not use thinner, benzine, or any other solvent as this
may cause the LM-092 to lose color or become deformed.
4. To remove stains inside of the box, wipe it using gauze soaked with water or neutral detergent
diluted with water. Do not use thinner, benzine, or any other solvent.
5. Never use oil-based ink or paint as these will inltrate the LM-092 and any contamination will not
be removed successfully.
6. In storing the LM-092, choose a location where it is not exposed to direct sunlight or ultraviolet
rays. (The LM-092 will be discolored if exposed to direct sunlight or ultraviolet rays for long
hours.)
7. If the LM-092 is not used, store it by placing it in the box and close the cover of the box.
8. Lubricant (silicone spray) is not included in the kit. Follow the precautions below for use.

2
Precautions on lubricant (silicone spray)
1. Use only silicone oil-type aerosol lubricant (silicone spray). Using grease or a spray that contains
oil other than silicone oil may damage the model.
2. Spray a small amount of the pre-prepared lubricant (silicone spray) on the neck skin and other
parts that do not impede functioning of the model and confirm that there are no problems
before proceeding with use.
* Caution
・ During the production process, small bubbles and chips may form at the bronchial bifurcation
and cannot be repaired.
・ The material used for molding in the manufacturing process may remain in the bronchial unit.
In this case, massage the bronchus in which the material remains with fingers and rinse the
material o󱐯.
1. The contents of this instruction manual are subject to change without notice.
2. This instruction manual may not be reproduced in part or in its entirety without permission.
3. Please contact the manufacturer in the event that any errors or omissions are found in the contents of
this instruction manual.
4. This product should be used only as described in this instruction manual. In particular, the product
should not be used in any way that contravenes the precautions noted in the instruction manual.

3
Table of Contents
1. Outline and Features
2. Components and Conguration
3. Handling the Model
4. Cleaning and Maintenance
Positioning with bronchial unit holders
5. Views of Bronchial Model
6. Storage Procedure
7. Specications

4
1. Outline and Features
Outline
This product can be used for insert training of ultrafine bronchoscopy as well as existing
bronchoscopy.
Features
・ The LM-092 is designed to represent very thin bronchi, which have never been successfully
modeled, by a special manufacturing method. The represented bronchi include even
quintenary bronchi (e.g., B1aiα). A very thin bronchoscope can be inserted up to a quintenary
bronchus.
・ The material is specialized silicone rubber. The sense of bronchoscopy insertion allows a feeling
like human-like texture due to elasticity. In addition, the internal bronchial unit is a human-like
color.
・ The bronchial unit and the stand are easily removable from the outer case.
・ The end of 3D structured distal bronchus is open and washable after insertion training.

5
2. Components and Conguration
Outer Box
Cover for Outer Box
Bronchoscope Inlet
Stand
Stand
Bronchial Unit Holder
Bronchial Unit

6
3. Handling the Model
＊Before inserting a bronchoscope, be sure to use the silicone spray as a lubricant.
Lubricant (silicone spray) is not included in the kit. Prepare lubricant in advance, referring
to the precautions.
3-1. Insert the nozzle of the silicone spray into the inside of the bronchial unit and spray the
silicone until atomization from the peripheral ends of the bronchial unit can be conrmed.
It is di󱐰cult to spray the silicone into the upward peripheral portions of the bronchial unit. For
those portions, additionally spray silicone by inserting the nozzle into each peripheral end.
Thoroughly apply silicone spray and start bronchoscope- insertion training.
3-2. The cover for the outer box can be removed.
Atomized Silicone Spray

7
To remove the cover, slide it in the arrow direction when it is open.
3-3. The bronchial unit can be removed from the box.
Hold the bronchoscope inlet of the bronchial unit and push it into the inside of the box.
Now remove the bronchial unit together with the stand from the outer box.

8
4. Cleaning and Maintenance
To remove the stain inside of the bronchial unit, it can be cleaned by the following procedure.
4-1. Hold the bronchoscope inlet of the bronchial unit and push it into the inside of the outer box.
4-2. Remove the bronchial unit together with the stand from the outer box.
4-3. Remove the bronchial unit from the stand.

9
4-4. Rinse the inside of the bronchial unit using neutral detergent and a test tube brush or the like.
＊Since a test tube brush does not reach the peripheral end, do not try to insert it excessively.
The bronchial unit may break.
4-5. Send water from the bronchoscope inlet and lightly massage the bronchial unit to clean its
inside.
＊In massaging the bronchial unit, never use your ngernails as this may result in cracking.
4-6. Wipe any water o󱐯 the bronchial unit. Shake the bronchial unit to drain its inside of any
water and place it in a location avoiding direct sunlight until it is completely dried.
8
8
8

10
4-7. Attach the bronchial unit to the bronchial unit holders.
4-8. Place the bronchial unit together with the stand in the outer box and pass the bronchoscope
inlet through from the inside of the box.

11
Positioning with bronchial unit holders
10

12
5. Views of Bronchial Model
Assign bronchial numbers using these views.
FRONT

13
BACK

14
7. Specications
Length Width Height Weight
Bronchialunit Approx.25cm Approx.24cm Approx.16cm
Case Approx.30cm Approx.32cm Approx.27cm Approx.3kg
(includingthebronchialunit)
Productname
6. Storage Procedure
1. Su󱐰ciently dry the bronchial unit (residual rinsing water may cause mold growth).
2. Check that the bronchial unit is attached to the specied bronchial unit holders and place it in
the box.
3. Close the cover of the box containing the bronchial unit and store the box in a location where
it is not exposed to direct sunlight or ultraviolet rays.