Kolpin Outdoors 35-3010 Installation and operating instructions

PLOW MOUNTING BRACKET
Assembly / Owner’s Manual
APPLICATION: Ranger 500; 570; 570 Crew; EV
Verify accessory fitment at Kolpin.com
Instr K100339 Rev 01 2021-03 Page 1 of 6
P/N 35-3010
PLOW MOUNTING BRACKET KIT

Instr K100339 Rev 01 2021-03 Page 2 of 6
INTRO
Thank you for purchasing Kolpin®engineered products. With proper installation, usage, care, and maintenance,
your Kolpin®product will last for years to come.
BEFORE YOU BEGIN
• Read and understand the entire installation manual, including all installation instructions, operating
instructions, safety warnings and guidelines before installing or operating your accessory. Failure to comply
may result in damage to the product and / or vehicle, and can lead to hazards up to and including death.
• Verify all parts and tools are accounted for. If parts are missing, do not return to the store. Call us for help, Toll
Free 1-877-956- 5746
• Follow all steps correctly and in the sequence described.
• Keep these instructions for future reference or for informational requests.
• To facilitate installation, make sure that your vehicle is clean and free of debris.
• All directions referring to right and left are from the rider perspective when sitting on the machine.
ASSEMBLY TIME
Approximately 14 minutes
SAFETY INFORMATION
Please read and understand all Cautions, Notices, and Warnings in this manual before you begin. In order to
protect you and your ATV / UTV, certain parts of the plow system and / or hardware are designed to fail when the
equipment is over-stressed.
Follow these guidelines to ensure satisfactory operation:
• Read this manual and your ATV / UTV operators manual before use.
• Periodically check for wear and tightness of all fasteners. Replace or re-torque fasteners as necessary.
• Before first use, set plow in the furthest right or left angled position to check for interference with the vehicle.
• Operate with extreme caution on slopes and rough terrain. Be familiar with the area before you plow.
• Be aware of immovable objects that could be hidden in the area you are plowing.
• To avoid damage when pushing snow into a pile, reverse direction before raising the plow blade.
• Do not ram the plow blade into piles of snow.
• For best results, set the suspension preload of your ATV / UTV to the stiffest setting.
• To reduce steering effort and increase mobility, set the air pressure of your tires to the maximum pressure
specification.
• The plow skids are adjustable. General skid setting is even with the plow wear bar bottom edge, higher
settings reduce the chance of rocks and gravel from being collected.
• To increase traction during plow operation, operators can try: Securing weight to the ATV / UTV for additional
tire downforce, reducing tire air pressure, or installing tire chains.

Instr K100339 Rev 01 2021-03 Page 3 of 6
WARNING
To avoid serious injury or death:
• Do not exceed 5 mph (8 km/h) with blade installed.
• Operate with extreme caution on slopes, steep grades, and rough terrain.
• Allow no riders on blade or ATV / UTV while moving or stationary.
• Keep bystanders away from the blade or ATV / UTV while moving or stationary.
• When pushing heavy material, direction control may become difficult.
• Before adjusting blade: stop ATV / UTV engine, set and lock brakes, raise and lock blade in up position.
• Do not attempt to raise blade by hand, use the lift mechanism only.
• Lower blade to down position when blade and ATV / UTV are not in use.
• Read blade instruction sheets and ATV / UTV Owner’s Manual.
REQUIRED SOLD SEPARATELY
Only parts for installation of the Plow Mounting Bracket Kit are included. For complete snow plow system
installation, additional items are required such as a plow push frame, vehicle plow mount, winch, and winch
mount. See www.Kolpin.com for products to complete your plow system.
TOOLS REQUIRED
• Safety Glasses
• Socket Set, Metric
• Torque Wrench
• Wrench Set, Metric
KIT CONTENTS

Instr K100339 Rev 01 2021-03 Page 4 of 6
REF QTY PART DESCRIPTION PART NUMBER
1 1 Plow Mount n/a
2 2 Screw – Hex Head, M12 x 1.75 x 45 mm 7518575
3 3 Screw – Hex Head, M10 x 1.5 x 35 mm n/a
4 3 Washer – M10 mm n/a
5 1 Bracket n/a
6 2 Nut – Hex Flange, M12 x 1.75 mm 7547327
73 Washer – Spring Lock, M10 7556378
INSTALLATION INSTRUCTIONS
VEHICLE PREPARATION
GENERAL
1. Park vehicle on a flat surface.
2. Shift vehicle into PARK.
3. Turn key to OFF position and remove key.
ACCESSORY INSTALLATION
1. Position mounting bracket qon vehicle front
bumper.
2. Loosely install three lower screws e, three lock
washers u, and three washers rinto bracket t
DO NOT TORQUE
3. Install two upper screws wand two nuts y.
Counter-hold nuts and torque to specification.
TORQUE
Upper Screws w:
34 ft-lbs (46 N·m)
IMPORTANT
If winch is installed, remove and discard two winch
mounting screws and install two upper screws w
through plow mount, winch mount, and vehicle.
4. Torque lower screws eto specification.
TORQUE
Lower Screws e:
34 ft-lbs (46 N·m)

Instr K100339 Rev 01 2021-03 Page 5 of 6
RECEIVER OPERATION
WARNING
Do not exceed maximum capacities. Exceeding
maximum capacities may result in receiver failure,
resulting in death, serious personal injury, or serious
damage to vehicle or property.
Maximum Tongue Weight: 100 lb (45 kg)
Maximum Tow Weight: 1200 lb (540 kg)

Instr K100339 Rev 01 2021-03 Page 6 of 6
WARRANTY
TWO YEAR LIMITED WARRANTY
For the period of two (2) years from the purchase date, Kolpin will replace for the original purchaser, free of
charge, any part or parts found upon examination by Kolpin to be defective in material, workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the
purchaser. If Kolpin determines that the product must be returned to the factory for credit, please call 1-877-956-
5746 for a Return Merchandise Authorization (RMA) number and shipping instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper
maintenance, normal wear, or other causes beyond the manufacturer’s control. In order to protect you and your
ATV, certain parts of the plow system and/or hardware are designed to fail when the equipment is over-stressed.
Parts that are lost due to loosening and improper maintenance are not covered under warranty. This warranty
does not cover removal or reinstallation labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s
warranty. Most hardware is general in nature and is easily obtained locally. Be sure to replace with minimum
metric class 8.8 specification.
Kolpin Outdoors, Inc.
Telephone: [phone]
Toll Free: (877)-956-5746
Fax Number: (800)-245-7569
www.Kolpin.com
Email: [email protected]