Kolpin Outdoors 35-1030 Setup guide

© 2021 Kolpin Outdoors Inc. REV 00
FRONT-CONNECT PLOW
MOUNT KIT
FOR HONDA TALON 1000
P/N 35-1030
ASSEMBLY / INSTALLATION MANUAL
Application
FRONT-CONNECT PLOW P SH FRAME NO. 35-0070
Before you begin, please read these instructions and check to be sure all parts and tools are accounted for.
The following instructions contain details required to install and service the contents of this kit.

2
© 2021 Kolpin Outdoors Inc. REV 00
INTRO
Thank you for purchasing Kolpin engineered products. With proper installation, usage, care, and maintenance, your Kolpin product will
last for years to come.
BEFORE YOU BEGIN
• Your Kolpin accessory is exclusively designed for your vehicle.
• Read and understand the entire installation manual, including all installation instructions, operating instructions, safety warnings
and guidelines before installing or operating your accessory. Failure to comply may result in damage to the product and / or
vehicle, and can lead to hazards up to and including death.
• • Verify all parts and tools are accounted for. If parts are missing, do not return to the store. Call us for help,
Toll Free 1-77-956- 5746
• Follow all steps correctly and in the sequence described.
• Keep these instructions for future reference or for informational requests.
• To facilitate installation, make sure that your vehicle is clean and free of debris.
• All directions referring to right and left are from the rider perspective when sitting on the machine.
ASSEMBLY TIME
Approximately 21 minutes
SAFETY INFORMATION
Please read and understand all Cautions, Notices, and Warnings in this manual before you begin. In order to protect you and your
ATV / TV, certain parts of the plow system and / or hardware are designed to fail when the equipment is over-stressed.
Follow these guidelines to ensure satisfactory operation:
• Read this manual and your ATV / TV operators manual before use.
• Periodically check for wear and tightness of all fasteners. Replace or re-torque fasteners as necessary.
• Before first use, set plow in the furthest right or left angled position to check for interference with the vehicle.
• Operate with extreme caution on slopes and rough terrain. Be familiar with the area before you plow.
• Be aware of immovable objects that could be hidden in the area you are plowing.
• To avoid damage when pushing snow into a pile, reverse direction before raising the plow blade.
• Do not ram the plow blade into piles of snow.
• For best results, set the suspension preload of your ATV / TV to the stiffest setting.
• To reduce steering effort and increase mobility, set the air pressure of your tires to the maximum pressure specification.
• The plow skids are adjustable. General skid setting is even with the plow wear bar bottom edge, higher settings reduce the
chance of rocks and gravel from being collected.
• To increase traction during plow operation, operators can try: Securing weight to the ATV / TV for additional tire downforce,
reducing tire air pressure, or installing tire chains.

3
© 2021 Kolpin Outdoors Inc. REV 00
REQUIRED SOLD SEPARATELY
Only parts for installation of the Plow Mounting Bracket Kit are included. For complete snow plow system
installation, additional items are required such as a plow push frame, vehicle plow mount, winch, and winch
mount. See www.Kolpin.com for products to complete your plow system.
TOOLS REQUIRED
• Safety Glasses
• Socket Set, Metric
• Torque Wrench
• Wrench Set, Metric
WARNING
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT EXCEED 5 MPH ( KMH) WITH BLADE INSTALLED
2. OPERATE WITH EXTREME CAUTION ON SLOPES, STEEP GRADES, AND ROUGH TERRAIN
3. ALLOW NO RIDERS ON BLADE OR ATV WHILE MOVING OR STATIONARY
4. KEEP BYSTANDERS AWAY FROM THE BLADE OR ATV WHILE MOVING OR STATIONARY
5. WHEN PUSHING HEAVY MATERIAL, DIRECTION CONTROL MAY BECOME DIFFICULT
6. BEFORE ADJUSTING BLADE: STOP ATV ENGINE; SET AND LOCK BRAKES; RAISE AND LOCK BLADE
7. LOWER BLADE TO DOWN POSITION WHEN BLADE AND ATV ARE NOT IN USE
8. READ BLADE INSTRUCTION SHEETS AND ATV OWNER’S MANUAL
! !

4
© 2021 Kolpin Outdoors Inc. REV 00
KIT CONTENTS
1
4
3
2
Item Qty Part Description Part Number
11Pioneer Mounting Bracket -
21Small Front Nut Plate, Painted, M10-1.5 -
31Large Rear Nut Plate, Painted, M10-1.5 -
42Hex Bolt, Zinc Plated, M8-1.25 x 25mm LG -
54Hex Bolt, Zinc Plated, M10-1.5 x 30mm LG -
62Lock Washer, Zinc Plated, M8 -
74Fender Washer, Zinc Plated, M10 -
84Lock Washer, Zinc Plated, M10 -
92Flat Washer, Zinc Plated, M8 -
10 1Instruction Guide (not shown) -
6
5
7
9
8

5
© 2021 Kolpin Outdoors Inc. REV 00
INSTALLATION INSTRUCTIONS
VEHICLE PREPARATION
GENERAL
1. Park vehicle on a flat surface.
2. Shift vehicle into park.
3. Turn key to OFF position and remove key.
4. Remove the lower bumper screws on each side, two
total. (See illustration 1-1).
Note, OEM screws will not
be re-used with plow mounting plate. Save for install
when plow mount is removed during off-season.
ACCESSORY INSTALLATION
5. Position small front nut plate (item #2) on top side of
front skid plate as shown. The nut plate threaded
holes will be aligned with the front holes in skid
plate. (See illustration 1-2).
6. Position large rear nut plate (item #3) on top side of
front skid plate as shown. The nut plate threaded
holes will be aligned with the rear holes in skid
plate. (See illustration 1-3). Note, the nut plate
holes may not be centered in the next steps
once everything is loosely bolted together.
Ill. 1-1
Ill. 1-2
Remove lower
screw on each
side
Ill. 1-3
Front holes
Item #2
Rear holes
Rear holes
Item #3

6
© 2021 Kolpin Outdoors Inc. REV 00
ACCESSORY
INSTALLATION
(continued)
7. Install the mount bracket (item
#1) using the M10 hardware
(items #5, #8, #7) through the
rear holes and into the rear
nut plate (item #3). You may
have to hold the nut plate in
place to get the screws
started. Then install the
remaining M10 hardware
through the mount plate and
into the front nut plate (item
#2) as shown. (See
illustrations 1-4 and 1-6).
Note, do not tighten
hardware at this time.
8. Install the M8 hardware (items
#4, #6, #9) through the mount
plate side tabs and into the
bumper holes as shown. (See
illustration 1-5).
9. Tighten all hardware to specifications.
Ill. 1-4
Items #5, #8, #7
10MM FASTENER TORQUE:
34 ft. lbs. (46 Nm)
Ill. 1-5
Items #4, #6, #9
MM FASTENER TORQUE:
17 ft. lbs. (23 Nm)
Ill. 1-6
Item #1

7
© 2021 Kolpin Outdoors Inc. REV 00
Two Year Limited Warranty
For the period of two (2) years from the purchase date, Kolpin will replace for the original purchaser,
free of charge, any part or parts found upon examination by Kolpin to be defective in material,
workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be
borne by the purchaser. If Kolpin determines that the product must be returned to the factory for
credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and
shipping instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse,
improper maintenance, normal wear, or other causes beyond the manufacturer’s control. In order to
protect you and your ATV, certain parts of the plow system and/or hardware are designed to fail
when the equipment is over-stressed. Parts that are lost due to loosening and improper
maintenance are not covered under warranty. This warranty does not cover removal or reinstallation
labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original
manufacturer’s warranty. Most hardware is general in nature and is easily obtained locally. Be sure
to replace with minimum metric class 8.8 specification.
Kolpin Outdoors, Inc.
Telephone: [phone]
Toll Free: ( 77)-956-5746
Fax Number: ( 00)-245-7569
www.kolpin.com
Email: [email protected]
WARRANTY