Kolpin Outdoors 15-0070 Installation and operating instructions

© 2021 Kolpin Outdoors Inc. REV 06
MID-MOUNT KIT
FOR HONDA ATV’s
P/N 15-1600
ASSEMBLY / OWNERS MANUAL
Application
PLOW PUS FRAME NO. 15-0070, 33-0000 or 33-0070
Before you begin, please read these instructions and check to be sure all parts and tools are ac-
counted for. The following instructions contain details required to install and service the contents of
this kit.

2
© 2021 Kolpin Outdoors Inc. REV 06
OPERATING INSTRUCTIONS
Congratulations! You’ve just purchased the most durable plow component in the industry. Kolpin plow components work great for
summer or winter plowing. With proper care and maintenance, your Kolpin plow system will last for years to come!
NOTICE
Pl w perati n requires
additi nal c mp nents f r perati n: Kolpin Plow
Blade, Kolpin Plow Push Frame, High Rise Plow
Push Frame, Winch Kit* and/or manual lift
Please read and understand all assembly instructions, notices and warnings before assembling and operating your Kolpin plow
system.
F ll w these guidelines t ensure satisfact ry perati n:
• Read this manual and your ATV/ UTV operators manual before use.
• Periodically check for wear and tightness of all fasteners. Replace or re-torque fasteners as necessary.
• Before first use, set plow in the furthest right or left angled position to check for interference with the vehicle.
• Operate with extreme caution on slopes and rough terrain. Be familiar with the area before you plow.
• Be aware of immovable objects that could be hidden in the area you are plowing.
• To avoid damage when pushing snow into a pile, reverse direction before raising the plow blade.
• Do not ram the plow blade into piles of snow.
• For best results, set the suspension preload of your ATV/ UTV to the stiffest setting.
• To reduce steering effort and increase mobility, set the air pressure of your tires to the maximum pressure specification.
• The plow skids are adjustable. General skid setting is even with the plow wear bar bottom edge, higher settings reduce the
chance of rocks and gravel from being collected.
• To increase traction during plow operation, operators can try: Securing weight to the ATV/ UTV for additional tire downforce,
reducing tire air pressure, or installing tire chains.
SAFETY INFORMATION
Our plow systems were designed with your safety in mind. Please read and understand all Cautions, Notices and Warnings in this
manual before you begin. In order to protect you and your ATV/UTV, certain parts of the plow system and/or hardware are designed to
fail when the equipment is over-stressed.
WARNING
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT EXCEED 5 MPH (8 KMH) WITH BLADE INSTALLED
2. OPERATE WITH EXTREME CAUTION ON SLOPES, STEEP GRADES, AND ROUGH TERRAIN
3. ALLOW NO RIDERS ON BLADE OR ATV WHILE MOVING OR STATIONARY
4. KEEP BYSTANDERS AWAY FROM THE BLADE OR ATV WHILE MOVING OR STATIONARY
5. WHEN PUSHING HEAVY MATERIAL, DIRECTION CONTROL MAY BECOME DIFFICULT
6. BEFORE ADJUSTING BLADE: STOP ATV ENGINE; SET AND LOCK BRAKES; RAISE AND LOCK BLADE
7. LOWER BLADE TO DOWN POSITION WHEN BLADE AND ATV ARE NOT IN USE
8. READ BLADE INSTRUCTION SHEETS AND ATV OWNER’S MANUAL
!!

3
© 2021 Kolpin Outdoors Inc. REV 06
Kit C ntents:
Item Qty Part Descripti n Part Number
11Blade Mount Weldment -
32Clevis Pin, Zinc Plated, 10mm x 35mm PUR1209
42air Pin, Zinc Plated, #3 PUR1249
54Flat Washer, Zinc Plated, M8 -
62Lock Washer, Zinc Plated, M6 -
72U-Bolt, Zinc Plated, M8-1.25 x 35mm x 50mm -
88ex Locknut, Zinc Plated, M8-1.25 -
11 1Instruction Guide (not shown) -
21Lift Strap Bracket -
10 2ex Bolt, Zinc Plated, M6-1.0 x 60mm -
92U-Bolt, Zinc Plated, M8-1.25 x 30mm x 50mm -

4
© 2021 Kolpin Outdoors Inc. REV 06
BEFORE YOU BEGIN:
• Y ur K lpin access ry is exclusively designed f r
y ur vehicle
• Please read and understand all instructi ns
• Verify all parts and t ls are acc unted f r
• T ensure a satisfact ry installati n, f ll w all steps
c rrectly and in the sequence described
• Keep these instructi ns f r future reference r f r
inf rmati nal requests
• T facilitate installati n, make sure that y ur vehicle
is clean and free f debris
• All directi ns referring t right and left are when the
rider is sitting n the machine
TOOLS REQUIRED:
• Basic Metric Hand Wrench and S cket Set
• T rque Wrench
• D N t use impact t ls t install hardware
APPROXIMATE ASSEMBLY TIME: 30 minutes
N te: Rem val f the skid plate is rec mmended. The plastic plate can be m dified (trimmed) r left ff vehicle.
N te: The inner fenders may need t be trimmed as pl w m unting bracket may t uch fenders.
Note: If any hardware is missing, do not return to the store. Call us to help,
Toll Free 1-877-956-5746.
SPARE KITS Hardware kit
P/N CYC5770
Item Descripti n
3Clevis Pin, Zinc Plated, 10mm x 35mm 2x
4air Pin, Zinc Plated, #3 2x
5Flat Washer, Zinc Plated, M8 4x
6Lock Washer, Zinc Plated, M6 2x
7U-Bolt, Zinc Plated, M8-1.25 x 35mm x 50mm 2x
8ex Locknut, Zinc Plated, M8-1.25 8x
9U-Bolt, Zinc Plated, M8-1.25 x 30mm x 50mm 2x
10 ex Bolt, Zinc Plated, M6-1.0 x 60mm 2x

5
© 2021 Kolpin Outdoors Inc. REV 06
Installati n Prep:
1. Remove the lower
plastic skid plate
to provide clamp-
ing access to the
lower frame
tubing. The skid
plate can be
trimmed to allow
the u-bolts
(installed later) to
fit through or it can
be saved for
installation during
plow off-season
usage.
M unt Plate
Installati n:
1. Place the u-bolts,
items #7 & #9,
over the
mainframe tubes
on each side of
the ATV, ahead of
the rear footrest
supports as shown. (See illustrations 1-1 and 1-2).
2. Place the blade mount, item #1, under the ATV. Attach the
blade mount to the ATV using the four u-bolts. Fasten u-bolts
using flat washers, item #5, over the slotted holes and M8
locknuts, items #8. (See illustrations 1-1 and 1-2).
3. Tighten the M8
locknuts to
specification.
8MM FASTENER TORQUE:
17 ft. lbs. (23 Nm)
Item #9
Ill. 1-1
Ill. 1-2
Item #7
Item #9
Remove front skidpan
and install Blade Mount
Item #7

6
© 2021 Kolpin Outdoors Inc. REV 06
M unt Plate Installati n (C ntinued):
4. Included is a lift strap bracket, which
is designed to protect the front
plastic grille from wear by the lift
strap. To install, remove existing
bolts from front grill. Install strap
bracket, item #2, using M6 screws,
item #10, with M6 lock washer, item
#6. (See illustration 1-3).
5. Tighten the M6 screws to
specification.
6MM FASTENER TORQUE:
7 ft. lbs. (9.5 Nm)
Item #2
Ill. 1-3
Item #10

7
© 2021 Kolpin Outdoors Inc. REV 06
Tw Year Limited Warranty
For the period of two (2) years from the purchase date, Kolpin will replace for the original purchaser,
free of charge, any part or parts found upon examination by Kolpin to be defective in material,
workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be
borne by the purchaser. If Kolpin determines that the product must be returned to the factory for
credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and
shipping instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse,
improper maintenance, normal wear, or other causes beyond the manufacturer’s control. In order to
protect you and your ATV, certain parts of the plow system and/or hardware are designed to fail
when the equipment is over-stressed. Parts that are lost due to loosening and improper
maintenance are not covered under warranty. This warranty does not cover removal or reinstallation
labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original
manufacturer’s warranty. Most hardware is general in nature and is easily obtained locally. Be sure
to replace with minimum metric class 8.8 specification.
K lpin Outd rs, Inc.
Teleph ne: (763)-478-5800
T ll Free: (877)-956-5746
Fax Number: (800)-245-7569
www.k lpin.c m
Email: cust merservice@k lpin.c m