Kolpin Outdoors 2900 Instruction sheet

1
© 2019 Kolpin Outdoors Inc. REV 04
John Deere - Full Hinged Windshield
Product Instructions | Part No: 2900
Tools Required:
Kolpin Outdoors, Inc. | 9955 59th Ave N | Plymouth, MN 55442
[phone] or [phone] | www.kolpin.com | [e-mail]
Application: Verify accessory fitment at Kolpin.com.
Before You Begin: Read these instructions and check
to be sure all parts are accounted for. If any items are miss-
ing, do not return to the store. Call us at 1-877-956-5746
for assistance. Please retain these instructions for future
reference and parts ordering information.
Dealers: Provide Instruction Manual to customer at time
of purchase.
Product Contents:
Item Description Qty Part Number
1 Upper Windshield Panel 1
2 Lower Windshield Panel 1
3 Clamp - 1.75" Diameter 6
K100137 (Qty 3)
4 Button Head Screw - M6 x 18mm *14
5 Lock Washer - M6 *14
6 Domed Shoulder Washer - M6 *8
7 Hinge 3 H3503P-01
8 M6 Locknut 12 7547453
9 T-Knob 2 K100197 (Qty 1)
10 Spacer 2
11 Bulb Seal - 48" 1 PUR3355 (Qty 1)
2
7
3
1
*Qty shown above is what is required to complete this Windshield assembly.
There will be extra hardware leftover which can be discarded.
5
4
8
9 10
11
6
• 10mm Wrench or Socket • 4mm Hex Wrench or Socket
• Shears or Wire Cutter
• Torque Wrench

2
© 2019 Kolpin Outdoors Inc. REV 04
Installation Instructions:
1. Shift vehicle transmission into PARK. Turn key to OFF po-
sition and remove from vehicle.
2. Carefully remove Windshield Panels from box and place on
a clean flat surface that won’t scratch the Windshield.
Leave protective film on both sides of the Windshield Panel
during installation process, except for areas where compo-
nents are mounted to the Panels.
3. Firmly press the Bulb Seal [Item 11] onto the bottom edge
of the Lower Windshield Panel [Item 2]. Cut any excess
length of the Bulb Seal using a Shears or Wire Cutter if
necessary. See Illustration 1-1.
4. Connect the Upper and Lower Windshield Panels together
with three Hinges [Item 7], and twelve M6 Locknuts [Item
8]. Do not fully tighten hardware yet. See Illustration 1-2.
5. Attach four 1.75” Diameter Clamps [Item 3] to the Upper
Windshield Panel. The Kolpin Logo on the Clamps should
face the outside of the vehicle when closed. Each Clamp
uses two Domed Shoulder Washers [Item 6], two Lock
Washers [Item 5] and two Button Head Screws [Item 4].
Leave the Clamps in the open position. Do not fully tighten
hardware yet. See Illustration 1-3.
6. Attach the two remaining 1.75” Diameter Clamps [Item 3] to
the Lower Windshield Panel. Each Clamp will be attached
with one T-Knob [Item 9], and one Spacer [Item 10]. Leave
Clamps in the open position. See Illustration 1-4.
Assembly Time: Approximately 30 minutes
Important: This product is exclusively designed for your vehicle. Please read the installation instructions thoroughly before begin-
ning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all
installation steps correctly in the sequence shown.
Ill. 1-1
Ill. 1-2
Ill. 1-3
Ill. 1-4

3
© 2019 Kolpin Outdoors Inc. REV 04
SPECIFIED FASTENER TORQUE:
7 ft. lbs. (84 in-lb) (9.5 Nm)
7. Carefully place the Windshield assembly onto the vehicle
roll cage. See Illustration 1-5.
8. Close the clamps and insert the hardware but do not fully
tighten. Each Clamp will use one Lock Washer [Item 5],
and one Button Head Screw [Item 4]. See Illustration 1-5.
9. Assure the Windshield is evenly aligned to the vehicle and
that the Bulb Seal [Item 11] is contacting the vehicle hood.
10. Tighten all of the Locknuts [Item 8] and Button Head
Screws [Item 4] to the torque specification below.
11. Check to make sure the Lower Windshield Panel can be
hinged open. Adjust Windshield and re-tighten to specifica-
tion if necessary. The Lower Windshield Panel must al-
ways be in the closed position while the vehicle is
moving or being transported. The Lower Windshield
should only be hinged open to access under the vehicle
hood.
12. Remove the protective film from both sides of the Wind-
shield Panel.
13. Re-inspect hardware before and after riding or transporting
the vehicle.
Ill. 1-5

4
© 2019 Kolpin Outdoors Inc. REV 04
Windshield Cleaning Information:
• Remove all dirt, mud, dust and debris from Windshield with water before cleaning.
• Use a mild soap or dishwashing detergent along with a soft sponge or soft cotton cloth to clean Windshield surface. Do not apply in direct sun-
light. Rinse with water immediately and dry with a soft cotton cloth or chamois.
• Always test cleaning agents in a small inconspicuous area prior to cleaning entire panel.
• Never use Windshield cleaning fluids (409, Windex, etc.), gasoline, high alkaline cleaners, or solvents.
• Never use abrasives, brushes, razor blades, scrapers, squeegees, gloves or dirty cloths.
For additional assistance, please contact Kolpin customer service department at
[phone] or [phone] or email [email protected].
One Year Limited Warranty
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts found upon exami-
nation by Kolpin to be defective in material, workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the purchaser. If Kolpin determines that the
product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and shipping
instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper maintenance, normal wear, or other causes
beyond the manufacturer’s control. In order to protect you and your ATV, certain parts of the accessory system and/or hardware are designed to fail
when the equipment is over-stressed. Parts that are lost due to loosening and improper maintenance are not covered under warranty. This warranty
does not cover removal or reinstallation labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s warranty. Most hardware is general in nature
and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specification.
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT TRAILER VEHICLE FACING REARWARD WITH WINDSHIELD INSTALLED. AIRFLOW MAY CAUSE
WINDSHIELD TO SEPARATE FROM VEHICLE, RESULTING IN AN ACCIDENT AND SEVERE INJURY OR
DEATH. REMOVE WINDSHIELD OR TRANSPORT VEHICLE IN ENCLOSED TRAILER.
2. UTVs ARE TO ONLY BE DRIVEN WITH CLEAN WINDSHIELDS FOR DRIVING VISIBILITY. IF DIRT OR DEBRIS
ACCUMULATES ON THE WINDSHIELD WHEN RIDING, STOP THE UTV AT THE NEXT SAFE LOCATION ON
THE TRAIL TO CLEAR OFF THE WINDSHIELD BEFORE YOU RESUME RIDING.
3. ONLY INSTALL WINDSHIELDS THAT ARE DESIGNED FOR THE MAKE AND MODEL OF THE UTV. INSTALLA-
TION OF A WINDSHIELD THAT WAS NOT DESIGNED FOR THE UTV MAKE AND MODEL CAN IMPACT WIND-
SHIELD DURABILITY AND PERFORMANCE.
4. READ AND UNDERSTAND WINDSHIELD INSTRUCTION SHEETS AND UTV OWNER MANUAL BEFORE WIND-
SHIELD INSTALLATION OR OPERATING THE VEHICLE.
5. PERIODICALLY CHECK FOR WEAR AND TIGHTNESS OF ALL FASTENERS. ALWAYS INSPECT BEFORE AND
AFTER RIDING OR TRAILERING. REPLACE OR RE-TORQUE FASTENERS AS NECESSARY.
!!
DANGER