Kontron CPS3105 User manual

D R A F T — F O R I N T E R N A L U S E O N L Y
The pulse of innovation
» User Guide «
CPS3105
Doc. ID: 1055-0548, Rev. 1.0
Date: July 3, 2013

D R A F T — F O R I N T E R N A L U S E O N L Y
2
www.kontron.com
User Guide
CPS3105
Revision History
Imprint
Kontron Europe GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Europe GmbH +49 (0) 800-SALESKONTRON
Sudetenstraße 7 [email protected]
D - 87600 Kaufbeuren Germany
For further information concerning other Kontron products, please visit our Internet website:
www.kontron.com.
Disclaimer
Copyright © 2013 Kontron AG. All rights reserved. All data is for information purposes only and not
guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate;
however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other
trademarks or registered trademarks are the property of their respective owners and are recognized.
Specifications are subject to change without notice.
Publication Title: CPS3105 User Guide
Doc. ID: 1055-0548
Rev. Brief Description of Changes Date of Issue
1.0 Initial issue 3-Jul-2013

D R A F T — F O R I N T E R N A L U S E O N L Y
3
www.kontron.com
User Guide
CPS3105
Contents
Revision History ..........................................................................................................2
Imprint .....................................................................................................................2
Disclaimer ..................................................................................................................2
Contents ....................................................................................................................3
Tables .......................................................................................................................4
Warranty ....................................................................................................................5
Proprietary Note ..........................................................................................................5
Trademarks ................................................................................................................5
Environmental Protection Statement ................................................................................5
1 Introduction ....................................................................................... 6
1.1 Board Overview ........................................................................................... 6
1.2 Board Diagrams........................................................................................... 6
1.2.1 Functional Block Diagram .............................................................................. 6
1.2.2 Front Panel ................................................................................................ 7
1.2.3 Board Layout .............................................................................................. 7
1.3 Technical Specification ................................................................................. 8
1.4 Standards .................................................................................................. 8
1.5 Related Publications..................................................................................... 9
2 Functional Description ......................................................................... 10
2.1 Board Interfaces......................................................................................... 10
2.1.1 Front Panel LED .......................................................................................... 10
2.1.2 XMC Interface ............................................................................................ 10
2.1.3 CompactPCI Serial Interface .......................................................................... 10
3 Installation ....................................................................................... 11
3.1 Safety ...................................................................................................... 11
3.2 General Instructions on Usage ....................................................................... 11
3.3 Board Installation ...................................................................................... 12
3.3.1 Hot Swap Insertion ..................................................................................... 12
3.3.2 Hot Swap Removal ...................................................................................... 12
3.3.3 XMC Module Installation ............................................................................... 12

D R A F T — F O R I N T E R N A L U S E O N L Y
4
www.kontron.com
User Guide
CPS3105
Tables
1 CPS3105 Main Specifications ..................................................................................8
2 Standards ..........................................................................................................8
3 Additional Standards for Boards Ordered with Ruggedized Service ................................... 9
4 Related Publications .............................................................................................9
5 Power Status LED ............................................................................................... 10
6 Compatibility Identification Block acc. to ANSI/VITA 42.3 ........................................... 10
7 XMC Module Current ............................................................................................ 10
Figures
1 CPS3105 Functional Block Diagram ........................................................................ 7
2 4 HP CPS3105 Front Panel .................................................................................... 8
3 4 HP CPS3105 Board Layout (Top View) ................................................................... 8

D R A F T — F O R I N T E R N A L U S E O N L Y
5
www.kontron.com
User Guide
CPS3105
Warranty
This Kontron product is warranted against defects in material and workmanship for the warranty period
from the date of shipment. During the warranty period, Kontron will at its discretion decide to repair
or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling
by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental
specifications or improper installation or maintenance.
Kontron will not be responsible for any defects or damages to other products not supplied by Kontron
that are caused by a faulty Kontron product.
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted by any
means, disclosed to others, or stored in any retrieval system or media without the prior written consent
of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. Howev-
er, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability
arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described here-
in, as seen fit by Kontron without further notice.
Trademarks
This document may include names, company logos and trademarks, which are registered trademarks
and, therefore, proprietary to their respective owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where possible.
Many of the components used (structural parts, printed circuit boards, connectors, etc.) are capable
of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with appli-
cable country, state, or local laws or regulations.

D R A F T — F O R I N T E R N A L U S E O N L Y
6
www.kontron.com
User Guide
CPS3105
1 Introduction
1.1 Board Overview
The CPS3105 is a 3U CompactPCI® Serial carrier board that provides support for one XMC module. The
carrier board is intended to offer system designers a cost-effective solution to expand the systems I/O
capability using a wide range of XMCs available on the market. The CPS3105 is equipped with a dedicat-
ed PCI Express switch between the onboard XMC connector and the CPCI-S.0 system connector provid-
ing two advantages. First, it decouples and buffers the PCI Express signals and restores signal
integrity. Second, it is able to convert one x4 PCI Express 3.0 data stream from the system side into one
x8 PCI Express 2.1 data stream to the XMC side. Thus, maximum data bandwidth can be provided to com-
monly available XMC modules based on PCI Express 2.1.
1.2 Board Diagrams
The following diagrams provide additional information concerning board functionality and component
layout.
1.2.1 Functional Block Diagram
Figure 1: CPS3105 Functional Block Diagram
Onboard Power Supplies 12 V
Power Enable
Pwr LED Onboard Power Supplies 12 V
PCIe
P1
Hot Swap Handle Power Enable
Front CompactPCI
Serial
x4 PCIe 3.0
PEX 8712
PCI Express
Switch
x8 PCIe 2.1
XMC Connector
PCIe x8

D R A F T — F O R I N T E R N A L U S E O N L Y
7
www.kontron.com
User Guide
CPS3105
1.2.2 Front Panel
Figure 2: 4 HP CPS3105 Front Panel
1.2.3 Board Layout
Figure 3: 4 HP CPS3105 Board Layout (Top View)
CPS3105
Pwr
XMC
Power Status LED
Pwr (green): Power Status of the CPS3105
PEX 8712
PCI Express
Switch
P1
Pwr LED
J2
Heat Sink

D R A F T — F O R I N T E R N A L U S E O N L Y
8
www.kontron.com
User Guide
CPS3105
1.3 Technical Specification
1.4 Standards
This product complies with the requirements of the following standards.
Table 1: CPS3105 Main Specifications
FEATURES SPECIFICATIONS
Switch
PCI Express Switch ExpressLane™ PEX 8712 PCI Express 3.0 switch from PLX Technology used to provide
maximum performance to an XMC module by spitting down the x4 PCI Express 3.0
interface to a x8 PCI Express 2.1/1.0 interface
Connectors
XMC XMC connector, J2 (P15), for connecting an XMC module to the CPS3105
CompactPCI Serial CompactPCI Serial interface on connector P1:
» Compliant with PICMG® CPCI-S.0 R 1.0 CompactPCI® Serial Specification
» Support for one x4 PCI Express 3.0 interface
Hot Swap
Hot Swap Hot swap handle with integrated hot swap switch for shutting down the power sup-
plies in order to safely remove the CPS3105 from the system
LED
Front Panel LED Power Status LED:
» Pwr (green): Power Status of the CPS3105
General
Mechanical 3U, 4 HP, CompactPCI Serial-compliant form factor
Power Consumption approx. 4.7 W (without XMC module)
Power Supply +12V DC in accordance with the CompactPCI® Serial Specification
Temperature Range Operational: 0°C to +60°C Standard
-40°C to +85°C Extended
Storage: -40°C to +85°C Without XMC module
Recommended Airflow Volumetric Flow Rate: > 10 cfm
Sufficient airflow must be provided to ensure optimal operation and long-term
reliability of the CPS3105.
Climatic Humidity 93% RH at 40 °C, non-condensing (acc. to IEC 60068-2-78)
Dimensions 100 mm x 160 mm
Board Weight 140 grams
Table 2: Standards
TYPE ASPECT STANDARD
CE Emission EN55022, EN50121-3-2, EN61000-6-3
Immission EN55024, EN50121-3-2, EN61000-6-2
Electrical Safety EN60950-1
Mechanical Mechanical Dimensions IEEE 1101.10
Environmental Climatic Humidity IEC60068-2-78
WEEE Directive 2002/96/EC
Waste electrical and electronic equipment
RoHS 2 Directive 2011/65/EU
Restriction of the use of certain hazardous sub-
stances in electrical and electronic equipment

D R A F T — F O R I N T E R N A L U S E O N L Y
9
www.kontron.com
User Guide
CPS3105
In addition, boards ordered with the ruggedized service comply with the following standards as well.
Note: Customers desiring to perform further environmental testing of the CPS3105 must contact
Kontron for assistance prior to performing any such testing.
Boards without conformal coating must not be exposed to a change of temperature which
can lead to condensation, as it may cause irreversible damage especially when the board
is powered up again.
Kontron does not accept any responsibility for damage to products resulting from destruc-
tive environmental testing.
1.5 Related Publications
The following publications contain information relating to this product.
Table 3: Additional Standards for Boards Ordered with Ruggedized Service
TYPE ASPECT STANDARD REMARKS
Environmental Vibration
(Sinusoidal)
IEC60068-2-6
IEC61131-2
Ruggedized version test parameters:
9-150 (Hz) frequency range
1 (g) acceleration
1 (oct/min) sweep rate
10 cycles/axis
3 axis
Single Shock IEC60068-2-27
IEC61131-2
Ruggedized version test parameters:
15 (g) acceleration
11 (ms) shock duration half sine
3 number of shocks per direction (total: 18)
6 directions
5 (s) recovery time
Table 4: Related Publications
PRODUCT PUBLICATION
CompactPCI Serial Systems PICMG® CPCI-S.0 R 1.0 CompactPCI® Serial Specification
All Kontron products Product Safety and Implementation Guide, ID 1021-9142
XMC ANSI/VITA 42.0-200x XMC Switched Mezzanine Card Auxiliary Standard
ANSI/VITA 42.3-2006 XMC PCI Express Protocol Layer Standard

D R A F T — F O R I N T E R N A L U S E O N L Y
10
www.kontron.com
User Guide
CPS3105
2 Functional Description
2.1 Board Interfaces
2.1.1 Front Panel LED
The CPS3105 provides one Power Status LED on the front panel.
2.1.2 XMC Interface
The CPS3105 uses one x8 PCI Express 2.1 interface operating at 5.0 GT/s and compliant with the ANSI/
VITA 42.0 and ANSI/VITA 42.3 specifications.
XMC modules are based on 3.3 V power along with variable power (VPWR) defined as either 5 V or 12 V
in the ANSI/VITA 42.0-200x XMC Switched Mezzanine Card Auxiliary Standard specification. On the
CPS3105, the VPWR is configured to 12 V.
Note: XMC integrators should carefully review the power ratings, cooling capacity and airflow re-
quirements in the application prior to installation of an XMC module on the CPS3105.
2.1.3 CompactPCI Serial Interface
The CPS3105 provides a standard CompactPCI Serial interface compliant with the PICMG® CPCI-S.0 R 1.0
CompactPCI® Serial Specification. The interface is comprised of one CompactPCI Serial connector, P1.
The pin assignment of the P1 connector is defined in the PICMG® CPCI-S.0 R 1.0 CompactPCI® Serial
Specification.
Table 5: Power Status LED
LED COLOR STATE FUNCTION
Pwr green Off Power off
On Power on
Table 6: Compatibility Identification Block acc. to ANSI/VITA 42.3
XMC Form Factor Standard XMC.3
Connector Identifier P15 (J2 on the CPS3105)
Protocol Identifier PCIe
Signal Voltage Parameter Standard
Keywords 1 - 3 8 Lane Link 0 5.0Gb/s
Table 7: XMC Module Current
VOLTAGE CONTINUOUS CURRENT PEAK CURRENT
3.3 V / 3.3 V AUX 2.0 A 2.5 A
+12 V / VPWR (12 V) 2.5 A 3.0 A
-12 V 0.15 A 0.2 A

D R A F T — F O R I N T E R N A L U S E O N L Y
11
www.kontron.com
User Guide
CPS3105
3 Installation
This chapter is oriented towards an application environment. Some aspects may, however, be applica-
ble to a development environment.
3.1 Safety
To ensure personnel safety and correct operation of this product, the following safety precautions
must be observed:
» All operations involving the CPS3105 require that personnel be familiar with system equip-
ment, safety requirements and the CPS3105.
» This product contains electrostatically sensitive components which can be seriously dam-
aged by electrical static discharge (ESD). Therefore, proper handling must be ensured at all
times.
» Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a
safe work station is not guaranteed, it is important for the user to be electrically discharged
before touching the product with his/her hands or tools. This is most easily done by touching
a metal part of your system housing.
» Do not handle this product out of its protective enclosure while it is not used for operational
purposes unless it is otherwise protected.
» Do not touch components, connector-pins or traces.
Kontron assumes no liability for any damage resulting from failure to comply with these requirements.
3.2 General Instructions on Usage
In order to maintain Kontron’s product warranty, this product must not be altered or modified in any
way. Changes or modifications to the device which are not explicitly approved by Kontron and de-
scribed in this manual or received from Kontron’s Technical Support as a special handling instruction
will void your warranty.
This device should only be installed in or connected to systems that fulfill all necessary technical and
specific environmental requirements. This applies also to the operational temperature range of the
specific board version, which must not be exceeded.

D R A F T — F O R I N T E R N A L U S E O N L Y
12
www.kontron.com
User Guide
CPS3105
3.3 Board Installation
The CPS3105 is designed for use in a peripheral slot with support for one PCI Express interface (recom-
mended configuration for maximum bandwith: x4 PCI Express 3.0).
3.3.1 Hot Swap Insertion
Prior to following the steps below, ensure that the safety requirements are met.
To insert the CPS3105 in a running system proceed as follows:
1. Ensure that the board ejection handle is open.
2. Insert the board into the slot designated until it makes contact with the backplane connec-
tors.
3. Using the ejector handle, engage the board with the backplane. When the ejector handle is
closed, the board is engaged.
The green PWR LED turns on indicating that the CPS3105 is operating.
4. Fasten the front panel retaining screws.
3.3.2 Hot Swap Removal
Prior to following the steps below, ensure that the safety requirements are met. When removing a
board from the system, particular attention must be paid to the components which may be hot, such as
heat sink, etc.
To preclude damage or data loss when removing the CPS3105, ensure that the operating system has
been informed of the pending removal and that the OS has indicated that it is safe to proceed.
To remove the CPS3105 from a running system proceed as follows:
1. Unlock the board ejection handle by pressing its release button.
The PWR LED turns off indicating that power has been removed from the CPS3105 and the
board may be removed from the system.
2. Unscrew the front panel retaining screws.
3. Using the ejector handle, disengage the board from the backplane and remove it from the
system.
3.3.3 XMC Module Installation
The CPS3105 supports the installation of an XMC module via the connector J2. For the initial installa-
tion and standard removal of the XMC module, refer to the documentation provided with the module.
Prior to installation or removal, ensure that the safety requirements are met. Particular attention must
be paid to the components which may be hot, such as heat sink, etc.

D R A F T — F O R I N T E R N A L U S E O N L Y
13
www.kontron.com
User Guide
CPS3105
CORPORATE OFFICES
Europe, Middle East & Africa
Oskar-von-Miller-Str. 1
85386 Eching / Munich
Germany
Tel.: + 49 (0) 8165 / 77 777
Fax: + 49 (0) 8165 / 77 219
[e-mail]
North America
14118 Stowe Drive
Poway, CA 92064-7147
USA
Tel.: + 1 888 294 4558
Fax: + 1 858 677 0898
[email protected]tron.com
Asia Pacific
17 Building,Block #1, ABP.
188 Southern West 4th Ring Road
Beijing 100070, P.R.China
Tel.: + 86 10 63751188
Fax: + 86 10 83682438
[email protected]