Kramer WP-20 User manual

WP-20 Quick Start
P/N:
2900- 300919QS
Rev:
6
Scan for full manual
WP-20 Quick Start Guide
This guide helps you install and use your WP-20 for the first time.
Go to www.kramerav.com/downloads/WP-20 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
WP-20 Wall plate
1 Power supply (12V DC)
1 Quick start guide
Step 2: Get to know your WP-20
US Version
EU / UK Version
#
Feature
Function
1
HDMI™LED
When HDMI is selected:
Lights orange when external audio is selected.
Lights green when embedded audio is selected.
LED is off when HDMI is not selected.
2
PC Graphics LED
When PC input is selected:
Lights orange when external audio is selected.
Lights green when there is no audio.
LED is off when the PC input is not selected
3
ON LED
The LED indicates the following:
Lights green –power is provided by a power adapter.
Lights orange –power is provided by PoE.
4
RESET Button
Short press to reset the device.
Long press (5 seconds) to reset the device to factory default parameters.
5
PC IN Input Connector
Connect to the PC graphics source (for example, a laptop).
6
HDMI IN Input Connector
Connect to an HDMI source (for example, a Blu-ray disk player).
7
ETHERNET RJ-45 Connector
Connect to the Ethernet LAN.
8
AUDIO IN 3.5mm Mini Jack
Connect to the unbalanced, stereo audio source (for example, the audio output of the
laptop).

US Version
EU / UK Version
#
Feature
Function
1
REMOTE 5-pin Terminal Block
Connect to the remote, contact-closure switches for remote control (see Step 8).
2
OPTION 4-way DIP-switch
Switches for setting the device behavior (see Step 4).
3
CONTROL 3-pin Terminal Block
Connect to the serial controller to control the WP-20 (for example, a PC).
4
AUDIO OUT 3-pin Terminal
Block
Connect to the unbalanced, stereo audio acceptor (for example, amplified speakers).
5
RS-232 3-pin Terminal Block
Connect to the PC to transfer data via RS-232 (for example, a serial controller for a
remote device).
6
12V DC Connector
Connect to the included power supply. Not needed on the WP-20 if there is a PoE
provider over HDBaseT.
7
GND Terminal
Connect to the common ground (optional).
8
HDBT OUT RJ-45 TP Connector
Connect to a compatible HDBT TP switcher or receiver (for example, the TP-780Rxr).
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 3: Connect inputs
Always switch OFF the power on each device before connecting it to your WP-20.
For best results, we recommend that you always use Kramer high-performance
cables to connect AV equipment to the WP-20.
RJ-45 Pinout:
For the Ethernet connector, see the
wiring diagram below:
PIN EIA /TIA 568B
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
Step 4: Set DIP switches
Video Switching Selection
Audio Switching Selection
DIP-
switch 1
DIP-
switch 2
Video Input Selection
DIP-
switch 3
DIP-
switch 4
Audio Input Selection
Off
Off
Automatic –Last connected. Where
more than one source is connected,
the last source has priority.
Off
Off
Automatic –Priority selection.
Embedded HDMI analog Audio In.
Off
On
Automatic –Priority selection.
HDMI 1 PC IN.
Off
On
Automatic –Priority selection.
Analog Audio In embedded HDMI.
On
Off
Manual
On
Off
Embedded HDMI
On
On
Manual
On
On
Analog Audio In

Step 5: Connect power
If the device is not powered via HDBT PoE, connect the 12V power supply to the WP-20 and plug the power supply into the
mains power.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 6: Mount WP-20
Mount the device in a suitable wall box. We recommend opening all holes in the walls of the box to assist in cooling the
WP-20.
Step 7: Connect outputs
Step 8: Operate WP-20
Operate WP-20 via Protocol 3000
Default IP Parameters
Parameter
Values
Default
Device Name
Any alphanumeric string up to 14 chars (can include hyphen, but not at the beginning or end)
KRAMER_
DHCP
ON/OFF
OFF
IP Address
Any valid IP address
192.168.1.39
Mask
Any valid network mask
255.255.0.0
Gateway
Any valid gateway address
192.168.0.1
TCP Port
0 to 65535
5000
UDP Port
0 to 65535
50000
Default RS-232 Communication Parameters
Parameter
Values
Baud Rate
115200
Data Bits
1
Stop Bits
1
Parity
None
Command Format
ASCII
Default Web Pages Logon Authentication
Parameter
Values
Name
Admin
Password
Admin

Operate WP-20 via Remote contact-closure switches Operate WP-20 via Web Page
#
Feature
Function
1
Input selection /
VGA phase shift
switch
Short press –Input toggle
Long press –Adjusts the VGA
phase shift
2
Step-in switch
Activates the step-in function if
relevant
3
Analog audio output
volume increase
control
Short press –Increases the
volume one step (0.5dB)
Long press –Increases the
volume from -83dB to +24dB in 10
seconds
4
Analog audio output
volume decrease
control
Short press –Decreases the
volume one step (0.5dB)
Long press –Decreases the
volume from +24dB to -83dB in 10
seconds
G
Ground
Connect to the common side of
the switches
Step 9: Technical Specifications
INPUTS:
Video:
1 HDMI on an HDMI connector, 1 VGA on a 15-pin HD (F) connector
Audio:
1 Unbalanced stereo audio on a 3.5mm mini jack
OUTPUTS:
1 HDBaseT on an RJ-45 connector, 1 Unbalanced stereo audio on a 3.5mm mini jack
PORTS:
1 RS-232 3-pin terminal block, 1 Ethernet on an RJ-45 connector
CONTROLS:
Remote switches for input switching and volume control, reset switch
STANDARDS:
HDMI with Deep Color, x.v.Color™ and 3D, HDCP—works with sources that support
HDCP repeater mode, HDBT certified
MAX. ANALOG AUDIO LEVEL:
3.1V p-p
THD:
0.013%
SNR:
–70dB
SUPPORTED WEB
BROWSERS:
Windows 7 and higher: Internet Explorer (32/64 bit) version 11, Firefox version 30,
Chrome version 35
MAC: Chrome version 35, Firefox version 27, Safari version 7
MAXIMUM TRANSMISSION
DISTANCE:
180m (590ft) up to 1080p @60Hz @24bpp in extended mode
130m (430ft) up to 1080p @60Hz @36bpp in normal mode
100m (330ft) up to 4K @60Hz (4:2:0) in normal mode
POWER CONSUMPTION:
12V DC, 850mA
OPERATING TEMP:
0° to +40°C (32° to 104°F)
STORAGE TEMP:
–40° to +70°C (–40° to
158°F)
HUMIDITY:
10% to 90%, RHL non-condensing
COOLING:
Convection
ENCLOSURE TYPE:
Aluminum
DIMENSIONS:
2 Gang USA 11.6 cm x 5.1cm x 11.4cm (4.57” x 2.01” x 4.49”) W, D, H
2 Gang EU 15.1cm x 4.7cm x 8.6cm (5.94” x 1.85” x 3.39”) W, D, H
WEIGHT:
0.23kg (0.51lbs) approx.
SHIPPING WEIGHT:
0.51kg (1.12lbs) approx.
ENVIRONMENTAL
REGULATORY COMPLIANCE:
Complies with appropriate requirements of RoHs and WEEE
VIBRATION:
ISTA 1A in carton (International Safe Transit Association)
COMPLIANCE STANDARDS:
CE
INCLUDED ACCESSORIES:
Power adapter
WARRANTY:
7 years parts and labor
Specifications are subject to change without notice at www.kramerav.com