KStrong AFX204002 Operator's manual

THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODELS:
IRSQ ROPE CLAMPS
USER INSTRUCTION MANUAL
AFX204002 and AFX204001
EN 567:2013

1. INTRODUCTION: The IRSQ Ascenders are classed as Personal Protective Equipment (PPE) by the European PPE Regulation EU
2016/425 and have been shown to comply with this Regulation through the Harmonized European Standard EN 567:2013.
These Ascenders are designed to minimize the risk of/provide protection against the danger of falling from heights. However, always
remember that no item of PPE can provide full protection and care must always be taken while carrying out the risk related activity.
2. TECHNICAL SPECIFICATION:
Please read and understand the manufacturer's instructions for each component or part of the complete system. Manufacturer's instructions
must be followed for proper use, care, and maintenance of this product. These instructions must be retained and be kept available for the user's
reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
Note: The user is advised to keep this user instructions document for the life of the product.
EN 567:2013 test Result/Comment
Achieves required performance as stated in EN 567:2013 (Pass)
Lock onto rope and accessory cord of diameter between 10 mm & 12 mm(Pass)
Ascenders lock automatically when tension is applied in the 'downward' direction. Rope allowed to slip
freely when force is applied to the rope clamp in the upward direction (Pass)
No visual evidence of significant damage to ropes or cords following strength testing (Pass)
Minimum width of handle opening=32 mm (Pass)
Testing using 10 mm rope:
Reference " subjected to 4kN applied 5 times in succession without visual evidence of
damage to device or rope.
Testing using 12 mm rope:
Reference " subjected to 4kN applied 5 times in succession without visual evidence of
damage to device or rope.
Maximum rope diameter: 12mm
No damage occurred to rope or rope clamp after 400N force is applied.
Minimum rope diameter : 10mm
No damage occurred to rope or rope clamp after 400N force is applied.
Maximum rope diameter : 12mm
No damage occurred to rope on rope clamp after 2000N force is applied.
Minimum rope diameter : 10mm
No damage occurred to rope or rope clamp after 2000N force is applied
AFX204002
AFX204001
Design & Ergonomics
(Clause 4.1)
Static Strength
(EN 567:2013)
Pushing Test
Pulling Test
3. PERFORMANCE AND LIMITATIONS OF USE: These Ascenders have been tested in accordance with EN 567:2013 and have achieved the
following performance levels as laid down in the norm.
01
Ref. Material Weight Works on Finish Certified to
AFX204002
AFX204001
Aluminium
Alloy 195.0gms 10.0mm to 12.0mm dia Kernmantle Rope Coloured, Anodized EN 567:2013
Ref. Material Weight Works on Finish Certified to
Aluminium
Alloy 195.0gms 10.0mm to 12.0mm dia Kernmantle Rope Coloured, Anodized EN 567:2013

4. POSSIBLE USAGE - AFX204002 & AFX204001: Rope Clamp is ideal to use during ascent and occasionally for hauling.
Use of Ascender is feasible only in combination with other parts of the total equipment needed. Therefore, check carefully whether the
products is compatible with other parts/components of the said equipment. Each of the components constituting the system ought to have the
relevant CE certification.
5. INSPECTION : Visually inspect the system before each use to ensure that it is in a serviceable condition and is operating correctly. If during
inspection, doubts are raised about the safety of the system or a component, these should be replaced either by the manufacturer or a
competent person.
6 PRECAUTIONS:
Ensure the Medical condition of the user does not affect his safety in normal and emergency use.
The equipment shall only be used by a person trained and competent in its safe use.
A rescue plan shall be in place to deal with any emergencies that could arise during the work.
It is essential to verify the free space required beneath the user at work place before each occasion of use so that in case of a fall there
will be no collision with ground or other obstacle in the fall path.
Ÿ
Ÿ
Ÿ
Ÿ
7. HOW TO USE:
PULL
STEP 1
Pull the spring lever
d o w n a n d th e n
towards outside with
the help of your
thumb.
STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Put the Kernmantle
rope of the dia 10-12
mm inside the empty
space left out after
opening of the spring
lever.
Now from the outside
direction press the
spring lever down
with the help of your
t h u m b , i t w i l l
automatically lock
the rope.
Now che ck that
ropes locked safely
with the spring lever
and there are no
chances of slippage
downwards.
Now put a Karabiner
is the two holes
adjacent to the rope.
It will ensure that the
rope dose not slip out
of the ascender.
Before starting the
asc ent from the
ground level, always
check the ascender
handle by pulling it
towards yourself and
ensure that the clamp
locks on the rope
w h e n p u l l e d
downwards & slides
upwards freely on the
rope.
ŸAFX204002 & AFX204001
02
8. ANCHORAGE STRENGTH : Ensure that the structure on to which the anchor is fitted is strong enough to withstand a minimum load of 12kN.
9. LIMITATIONS:
It should be the personal property of its user.
It should not be used in highly acid or basic environments.
ŸThis equipment shall not be used out side its limitation, or for any purpose other than that for which it is intended.
The ascender has been tested to EN 567:2013 and is appropriate only for single person use with an energy absorber as per
EN 355:2002.
Ensure that the equipment is compatible with other items when assembled into a system.
It is essential for the safety of user that if the product is resold outside the original country of destination, the reseller shall provided
instruction for use, for maintenance, for periodic examination and for repair in the language of the country in which product in to be used.
ŸDo not exceed the limits of this equipment!. KStrong cannot be held liable for any accident, whether direct or indirect, resulting from a
usage other than that provided for in this guide.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ

03
10. COMPATIBILITY: To optimize protection, in some instance it may be necessary to use the anchor with suitable PPE such as: boots/ gloves/
helmet and ear protection. In this case, before carrying out the risk-related activity, consult your supplier to ensure that all your protective
products are compatible and suitable for your application.
11. REPAIR: If the product becomes damaged, it will NOT provide the optimum level of protection, and therefore should be immediately removed
from service. It needs to be inspected to see if it is replaced or repaired. Never use the damaged product. Repair is only permitted by the
manufacturer or a nominated repair centre or individual approved by the manufacturer
12. WITHDRAWAL FROM USE : If the system has been used to arrest a fall, it should be removed from service and returned to the manufacturer
or a competent repair centre for servicing and retest.
13. CLEANING & MAINTENANCE: In case of minor soiling, wipe the anchor with cotton cloth or a soft brush. Do not use any abrasive material.
0 0
For intensive cleaning wash the anchor in water at a temperature between 30 C to 60 C by using a neutral detergent (pH 7). The washing
0
temperature should not exceed 60 C. Do not use acidic or basic detergents.
14. STORAGE AND TRANSPORT: When not in use, store the anchor in a well-ventilated area away from heavily acidic or basic environment.
Never place heavy items on top of it. Also ensure that it is stored away from chemically hazardous environment. Preferably storage should be
in dry environment.
15. WARNING:
ŸDo not make any alterations or additions to the equipment without the manufacturer’s prior written consent and that any repair shall only
be carried out by personnel trained by the manufacturer & duly authorized by him.
ŸT he equipment shall not be used out side its limitation, or for any purpose other than that for which it is intended.
ŸAn inappropriate use can cause serious and even fatal accidents.
The Ascender is marked with :
(i) Type or product code
(ii) The CE mark showing that the product meets the
requirements of the PPE Regulation (EU) 2016/425
(iii) Minimum breaking load
(iv) Identification of the manufacturer
(v) EN Norms to which it complies
UP
MARKING
FOR
ROPE :
10
~
12MM
EN 567:2013

04
LIFESPAN: The estimated product Lifespan is 10 years from the date of manufacture. The following factors can reduce the Lifespan of the product:
intense use, contact with chemical substances, specially aggressive environments, extreme temperature exposure, UV exposure, abrasions, cuts,
violent impacts, bad use or maintenance.
DISCLAIMER: Prior to use, the end user must read and understand the manufacturer's instructions supplied with this product at the time of
shipment and seek training from their employer's trained personnel on the proper usage of the product. Manufacturer is not liable or responsible for
any loss, damage or injury caused or incurred by any person on grounds of improper usage or installation of this product.
Periodic examination
next due date
Product
Model & type/Identification
Trade Name
Address
Identification number
Manufacturer
Tel, email into use
Year of manufacture
Purchase Date
Date first put into use
Other relevant information (eg. document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Date Name and signature
of competent person
Reason for entry
(periodic examination
or repair)
Defects noted, repairs
relevant information
carried out and other
EQUIPMENT RECORD

05

06

AKS-AFA930401-110121-V2
Certification Body:
SATRA Technology Europe Ltd, Bracetown Business Park, Clonee, Dublin D15 YN2P Ireland (Notified Body 2777)
Ongoing Assessment Body:
SGS Fimko Oy, Takomotie 8, FI-00380 Helsinki, Finland (Notified Body 0598)
www.kstrong.com
USA South America ASIA
KStrong Inc.
150 N. Radnor Chester Road Suite F200
Radnor, Pennsylvania 19087 United States
Contact number : 1-833-KSTRONG
For EU Declaration, please visit https://kstrong.com/asia/eu-declaration-form/