KStrong AFA930950 Operator's manual

THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODEL:
EDGE DOOR ANCHOR
USER INSTRUCTION MANUAL
AFA930950
EN 795:2012 TYPE B

Please read and understand the manufacturer's instructions for each component or part of the complete system. Manufacturer's instructions
must be followed for proper use, care, and maintenance of this product. These instructions must be retained and be kept available for the
user's reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
Note: The user is advised to keep this user instructions document for the life of the product.
1. INTRODUCTION: The Door Anchor is classed as a Personal Protective Equipment (PPE) by the European PPE Regulation (EU)2016/425
and have been shown to comply with this Regulation through the Harmonized European Standard EN 795:2012 Type B.
This Anchor is designed to minimise the risk of/provide protection against the danger of falling from heights. However, always remember
that no item of PPE can provide full protection and care must always be taken while carrying out the risk activity.
2. PERFORMANCE AND LIMITATIONS OF USE: The Anchor has been tested in accordance with EN 795:2012 Type B and has achieved the
following performance levels:-
related
EN 795 : 2012 Type B test Result/Comment
General Requirements
for Anchor devices
(Clause 4.2)
Static Strength
(Clause 4.4.2.3)
Dynamic Strength & Integrity Test
(Clause 4.4.2.2)
Corrosion Resistance
(Clause 4.7)
(PASS)
No sharp edges (PASS).
Sustained a force of 12 kN for 3 minutes (PASS).
When tested with rigid steel mass of 100 kg, the test mass held after test with the
device remaining stable throughout. (PASS). .
Anchor Holds an increased load of 300kg for 3 min following dynamic test.
No corrosion evident after 48 hours of salt spray testing. (PASS)
02
3. APPLICATION : The Door Anchor provides a non-penetrating anchor point that can be installed by just compressing it against the door or
window frame, jamming itself between the two vertical sides.
4. INSPECTION : Visually inspect the system before each use to ensure that it is in a serviceable condition and is operating correctly. If during
inspection, doubts are raised about the safety of the system or a component, these should be replaced either by the manufacturer or a
competent person.
5. PRECAUTIONS:
ŸEnsure the Medical condition of the user does not affect his safety in normal and emergency use.
ŸThe equipment shall only be used by a person trained and competent in its safe use.
ŸA rescue plan shall be in place to deal with any emergencies that could arise during the work.
ŸIt is essential to verify the free space required beneath the user at
work place before each occasion of use so that in case of a fall
there will be no collision with ground or other obstacle in the fall
path.
6. INSTRUCTIONS FOR USAGE:
ŸDoor anchor is intended to be compressed against the Door or
Window frame jamming itself between the two vertical sides.
ŸRemove the locking pin & adjust the opening of the door anchor
arms, so that the jamming frames can take their places, now insert
the locking pin into nearest hole of the door anchor body.
ŸSet the locking lever into open position & tight the cup washer for
proper grip. Lock the threaded bar by moving the locking lever into
closed position.
ŸBoth Anchorage eyes can be used as the anchorage points.
Tested in Direction

7. ANCHORAGE POINT: Ensure that the structure on to which the anchor ŸIt is essential for the safety of user that if the product is resold
is fitted is strong enought to withstand a load of 12kN. outside the original country of destination, the reseller shall
provided instruction for use, for maintenance, for periodic
8. COMPATIBILITY :To optimise protection, in some instance it may be examination and for repair in the language of the country in which
necessary to use the anchor with suitable ppe such as boots/ gloves/ product in to be used.
helmet/ ear defenders. In this case, before carrying out the risk-related
activity, consult your supplier to ensure that all your protective products 11. REPAIR : If the product becomes damaged, it will NOT provide the
are compatible and suitable for your application. optimum level of protection, and therefore should be immediately
removed from service. Never use the damaged product. Repair is
9. ADVICE AND INFORMATION: permitted, provided that it is either done by the manufacturer or a
competent repair centre or individual approved by the manufacturer.
ŸWhen The Anchor Device is used as part of a fall arrest system, the
user shall be equipped with a means of limiting the maximum 12.WITHDRAWAL FROM USE : If the system has been used to arrest a
dynamic forces exerted on the user during the arrest of a fall to a fall, it should be removed from service and returned to the manufacturer
maximum of 6 kN. or a competent repair centre for servicing and re test.
ŸAnchor device is marked with next inspection due date.
ŸAnchor device should only be used for personal fall protection 13.CLEANING & MAINTENANCE: In case of minor soiling, wipe the
equipment and not for lifting equipment. anchorage device with cotton cloth or a soft brush. Do not use any
abrasive material. For intensive cleaning wash the anchorage device in
ŸAny dangers that may arise by the use of combinations of items of water at a temperature not more than 40ºC by using a neutral detergent
equipment in which the safe function of any one item is affected by (pH7). The washing temperature should not exceed 40ºC. Do not use
or interferes with the safe function of another. acidic or basic detergents.
ŸAnchor slide should move freely, Please check for any cracks,
permanent deformation. 14. STORAGE AND TRANSPORT: When not in use, store the anchorage
ŸIt is advisable to use the dorsal attachment D-Ring of the harness for device in a well-ventilated area away from heavily acidic or basic
connection. environment. Never place heavy items on top of it. Also ensure that it is
stored away from chemically hazardous environment preferably
ŸIt is essential for safety that the anchor device or anchor point
storage should be in dry environment.
should always be positioned, and the work carried out in such a way,
as to minimize both the potential for falls and potential fall distance.
Ensure that manufacturer's packing is used during transportation to
Where it is essential that the anchor device/point is placed above
prevent damage. In case original packing is not available, use polybag
the position of the user.
which is sealed to prevent moisture.
ŸA full body harness is the only acceptable body holding device that
can be used in a fall arrest system. 15. WARNING:
ŸFollowing conditions may be hazardous & may affect the ŸDo not make any alteration or additions to the equipment without
performance of Anchor- the manufacturer’s prior written consent and repair shall only be
ŸExtreme temperature. carried out by personnel trained by the manufacture & duly
ŸTrailing or looping of Lanyards over sharp edges. authorized by him.
ŸExtreme acidic or basic environments. ŸThe equipment shall not be used out side its limitation, or for any
purpose other than that for which it is intended.
ŸAbrasive or sharp edge structures which can damage the
equipment. 16. PERIODIC EXAMINATION:
ŸChemical Reagents.
ŸIt is important to conduct regular periodic examination of the
ŸClimatic exposure. product because the safety of the user depends upon the
ŸStandard packaging supplied from manufacturer should be used continued efficiency & durability of the product.
during transportation to protect the equipment against damage. ŸThe frequency of examination should be at least once in a year
ŸIt is important to conduct regular periodic examination of the product however it can be more than once if legislation requires, or
because the safety of the user depends upon the continued frequency of use is high or environmental conditions have an
efficiency and durability of the product. adverse effect on it eg. excessive rain, sea side environment,
excessive heat etc.
10. LIMITATIONS : ŸIt is emphasized that the examination be conducted Only by the
ŸIt should be the personal property of its user. manufacturer or by a person / organization authorized by the
manufacturer strictly in accordance with their periodic
ŸIt should not be used in highly acid or basic environment.
examination procedures.
ŸThe anchor has been tested to EN 795:2012 Type B and is
ŸIt is also advised the competent person be duly trained and
appropriate for maximum of 1 Person use with energy absorber as
authorized by the manufacturer.
per EN 355:2002 that is rated to user mass of up to 100kg.
ŸEnsure that all markings on the product are legible and can be
ŸEnsure that the Anchorage installed directly above the user’s
clearly read.
head.
ŸEnsure that the equipment is compatible with other items when
assembled into a system.
02

The anchor is marked with: iii) Type or product code
i) The CE mark showing that iv) Date of manufacturing
v) UID for traceability
the product meets the
vi) Norm Reference
requirments of the ppe
vii) Load Capacity
Regulation (EU) 2016/425 viii) Read the instruction
ii) Identification of the
Before Use.
manufacturer
QRCODE
Load Capacity: 100 Kg
UID: XXXXXXXXXXXX
Date of mfg.: MM/YYYY
EN 795:2012 Type B
KStrong Inc. 150 N. Radnor Chester Road
Suite F200 Radnor, Pennsylvania 19087 United States
MAX
1
KStrong.com
Made In India
Door Anchor
AFA930950
(i)
(iv)
(v)
(vi)
(vii)
(viii)
(iii)(iii)
(ii)
Marking
Certification Body :
SATRA Technology Europe Ltd, Bracetown Business Park, Clonee, Dublin D15 YN2P Ireland (Notified Body 2777)
Ongoing Assessment Body:
SGS Fimko Oy, Takomotie 8, FI-00380 Helsinki, Finland (Notified Body 0598)
For EU Declaration, please visit https://kstrong.com/asia/eu-declaration-form/
AKS/AFA930950/030821/V3
LIFESPAN: The estimated product Lifespan is 10 years from the date of manufacture. The following factors can reduce the Lifespan of the product:
intense use, contact with chemical substances, specially aggressive environments, extreme temperature exposure, UV exposure, abrasions, cuts, violent
impacts, bad use or maintenance.
DISCLAIMER: Prior to use, the end user must read and understand the manufacturer's instructions supplied with this product at the time of shipment and
seek training from their employer's trained personnel on the proper usage of the product. Manufacturer is not liable or responsible for any loss, damage or
injury caused or incurred by any person on grounds of improper usage or installation of this product.
Periodic examination
next due date
Product
Model & type/Identification
Trade Name
Address
Identification number
Manufacturer
Tel, email into use
Year of manufacture
Purchase Date
Date first put into use
Other relevant information (eg. document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Date Name and signature
of competent person
Reason for entry
(periodic examination
or repair)
Defects noted, repairs
relevant information
carried out and other
EQUIPMENT RECORD
www.kstrong.com
USA South America ASIA
KStrong Inc.
150 N. Radnor Chester Road Suite F200
Radnor, Pennsylvania 19087 United States
Contact number : 1-833-KSTRONG
Contact Email: [email protected]