KYLAND Technology SICOM3000A Series Assembly instructions

SICOM3000A Industrial Ethernet Switch
Hardware Installation Manual
Publication Data: Mar. 2019
Version: V1.2
No.: 112020167

SICOM3000A Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as
accurate and as updated as possible. This document is not guaranteed to be error-free, and
we reserve the right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, in any form or by any means without the prior written permission of KYLAND
Corporation.
Copyright © 2019 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial
damage or destruction of the device should be avoided. Before using the device, read this
manual carefully for personal and equipment safety. Please keep the manual for further
reference. Kyland is not liable to any personal or equipment damage caused by violation of
this notice.
Do not place the device near water sources or damp areas. Keep the ambient relative
humidity within the range from 5% to 95% (non-condensing).
Do not place the device in an environment with high magnetic field, strong shock, or high
temperature. Keep the working and storage temperatures within the allowed range.
Install and place the device securely and firmly.
Please keep the device clean; if necessary, wipe it with a soft cotton cloth.
Do not place any irrelevant materials on the device or cables. Ensure adequate heat
dissipation and tidy cable layout without knots.
Wear antistatic gloves or take other protective measures when operating the device.
Avoid any exposed metal wires because they may be oxidized or electrified.
Install the device in accordance with related national and local regulations.
Before power-on, make sure the power supply is within the allowed range of the device.
High voltage may damage the device.
Power connectors and other connectors should be firmly interconnected.
Do not plug in or out the power supply with wet hands. When the device is powered on,
do not touch the device or any parts with wet hands.
Before operating a device connected to a power cable, remove all jewelry (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
Do not operate the device or connect or disconnect cables during an electrical storm.
Use compatible connectors and cables. If you are not sure, contact our sales or technical
support personnel for confirmation.

Do not disassemble the device by yourself. When an anomaly occurs, contact our sales
or technical support personnel.
If any part is lost, contact our sales or technical support personnel to purchase the
substitute. Do not purchase parts from other channels.
Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
In the following cases, please immediately shut down your power supply and contact your
Kyland representative:
Water gets into the equipment.
Equipment damage or shell damage.
Equipment operation or performance has abnormally changed.
The equipment emits odor, smoke or abnormal noise.
The following information applies when operating this device in hazardous locations:
Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous Locations, or
nonhazardous locations only.
Cet appareillage est utilisable dans les emplacements de Classe I, Division 2, Groupes A, B,
C et D, ou dans les emplacements non dangereux seulement.
WARNING: EXPLOSION HAZARD
Do not disconnect equipment while the circuit is live or unless the area is known to be
free of ignitable concentrations.
Substitution of any component may impair suitability for Class I, Division 2.
AVERTISSEMENT: RISQUE D'EXPLOSION
Avant de deconnecter l'equipement, couper le courant ou s'assurer que l'emplacement
est designe non dangereux.
La substitution de composants peut rendre ce materiel inacceptable pour les
emplacements de Classe I, Division 2.

NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
NOTE: If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.

I
Contents
1 Product Overview...............................................................................................................1
1.1 Small products（The shell width is 66 mm）...............................................................1
1.2 Medium products（The shell width is 88 mm）...........................................................2
1.3 Large products（The shell width is 102 mm）.............................................................1
2 Structure and Interface.......................................................................................................3
2.1 Front Panel ..................................................................................................................3
2.2 Top Panel.....................................................................................................................6
2.2.1 Low voltage（L2/L5）products Top Panel ............................................................6
2.2.2 High voltage（HV）products Top Panel ...............................................................7
3 Mounting.............................................................................................................................8
3.1 Dimension Drawing......................................................................................................8
3.2......................................................................................................................................9
3.3 Mounting Modes and Steps .......................................................................................10
3.3.1 DIN-Rail Mounting...............................................................................................11
3.3.2 Panel Mounting....................................................................................................12
4 Connection .......................................................................................................................15
4.1 10/100Base-T(X) Ethernet Port..................................................................................15
4.2 10/100/1000Base-T(X) Ethernet Port.........................................................................16
4.3 100/1000Base-X, 10/100/1000Base-T(X) SFP slot....................................................18
4.3.1 SFP Optical Module.............................................................................................19
4.3.2 SFP Electrical Module .........................................................................................20
4.4 Console Port ..............................................................................................................21
4.4.1 RJ45 Console port...............................................................................................21
4.5 Grounding..................................................................................................................22
4.6 Power Terminal Block................................................................................................22
4.7 Alarm Terminal Block.................................................................................................24
5 Reset................................................................................................................................26

II
6 LEDs.................................................................................................................................27
7 Switch Access ..................................................................................................................28
7.1 Access through Console Port.....................................................................................28
7.2 Access through Telnet ...............................................................................................30
7.3 Access through Web..................................................................................................31
8 Basic Features and Specifications....................................................................................32

Product Overview
1
1 Product Overview
SICOM3000A includes a series of green low-consumption industrial Ethernet switches.
The series switches provide RJ45 Consoleport, and supports one-touch recovery, and
network management through Web, Telnet, and console port.
1.1 Small products（The shell width is 66 mm）
The series switches provide four 100/1000Base-X, 10/100/1000Base-T(X) SFP slots
(Gigabit SFP Slot), and eight 10/100Base-T(X) Ethernet ports, The SPF slots support the
optical power detection function. For details, see the following table.
Table 1 Models
Models
SICOM3000A-Ports-Connector-PS1-PS2
Code definition
Code option
Ports：
4GX8T、4SFP8T、2GX8T、2SFP8T、8T、6T
Note ：
4GX8T ： four 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ； eight
10/100Base-T(X) ports
4SFP8T ： four 100Base-X SFP slots ； eight 10/100Base-T(X) ports
2GX8T ： two 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ； eight
10/100Base-T(X) ports
2SFP8T ： two 100Base-X SFP slots ； eight 10/100Base-T(X) ports
8T ： eight 10/100Base-T(X) ports
6T ： six 10/100Base-T(X) ports
Connector: parameters for
S/M
Ports can’t work at 100Base-FX in the default,sfp slots support configure
the 100Base-FX
PS1-PS2：power input
L2-L2 (24-48VDC, redundant power input)
L5-L5 (12-24VDC, redundant power input)
HV：100-240VAC,50/60Hz;110-220VDC

Product Overview
2
1.2 Medium products（The shell width is 88 mm）
The series switches provide either four 100/1000Base-X, 10/100/1000Base-T(X) SFP
slots (Gigabit SFP Slot), and eight 10/100/1000Base-T(X) Ethernet ports, or eight
10/100/1000Base-T(X) Ethernet ports. The SPF slots support the optical power detection
function. For details, see the following table.
Table 2 Models
Models
SICOM3000A-Ports-Connector-PS1-PS2
Code
Code option
Ports：
4GX8GE、2GX8GE、8GE
Notes ：
4GX8GE: four 100/1000Base-X ， 10/100/1000Base-T(X) SFPslots ； eight
10/100/1000Base-T(X)ports
2GX8GE ： two 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ； eight
10/100/1000Base-T(X)ports
8GE:eight 10/100/1000Base-T(X)ports
Connector：parameters for
S/M
Ports can’t work at 100Base-FX in the default,sfp slots support configure
the 100Base-FX
PS1-PS2：power input
L2-L2 (24-48VDC, redundant power input)
L5-L5 (12-24VDC, redundant power input)
HV：100-240VAC,50/60Hz;110-220VDC

Product Overview
1
1.3 Large products（The shell width is 102 mm）
The series switches provide either sixteen 100/1000Base-X, 10/100/1000Base-T(X)
SFP slots (Gigabit SFP Slot), and four 10/100/1000Base-T(X) Ethernet ports, or four
100/1000Base-X, 10/100/1000Base-T(X) SFP slots (Gigabit SFP Slot), and sixteen
10/100/1000Base-T(X) Ethernet ports. The SPF slots support the optical power detection
function. For details, see the following table.
Table 3 Models
Models
SICOM3000A-Ports-Connector-PS1-PS2
Code
Code option
Ports：
12GX8GE、8GX8GE、8GX8T、8SFP8T、4GX16GE、4GX16T、4SFP16T、
2GX16GE、2GX16T、16GE、16T
Notes ：
12GX8GE ： twelve 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ；
eight 10/100/1000Base-T(X)ports
8GX8GE: eight 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ； eight
10/100/1000Base-T(X)ports
8GX8T ： eight 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ； eight
10/100Base-T(X)ports
8SFP8T ： eight 100Base-X ， 10/100Base-T(X) SFP slots ； eight
10/100Base-T(X)ports
4GX16GE ： four 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ；
sixteen 10/100/1000Base-T(X)ports
4GX16T ： four 100/1000Base-X ， 10/100/1000Base-T(X) SFP slots ； sixteen
10/100Base-T(X)ports
4SFP16T ： four 100Base-X ， 10/100Base-T(X) SFP slots ； sixteen
10/100Base-T(X)ports
2GX16GE ： two 100/1000Base-X ， 10/100/1000Base-T(X) SFPslots ； sixt

Product Overview
2
een 10/100/1000Base-T(X)ports
2GX16T ： two 100/1000Base-X ， 10/100/1000Base-T(X) SFPslots ； sixteen
10/100Base-T(X)ports
16GE ： sixteen 10/100/1000Base-T(X)ports
16T ： sixteen 10/100Base-T(X)ports
Connector：parameters for
S/M
Ports can’t work at 100Base-FX in the default,sfp slots support configure
the 100Base-FX
PS1-PS2：power input
L2-L2 (24-48VDC, redundant power input)
L5-L5 (12-24VDC, redundant power input)
HV：100-240VAC,50/60Hz;110-220VDC

Structure and Interface
3
2 Structure and Interface
Caution:
It is recommended to purchase the port dustproof shield (optional) to keep ports clean and
ensure device performance.
2.1 Front Panel
Small product front panel
Figure 1 Medium product front panel
(1) Power 1 LED
(2) Power 2 LED
(3) Running LED
(4) Ring LED
(5) Alarm LED
(6) Reset button
(7) 10/100/1000Base-X SFP port connection status LED (green)
(8) 10/100/1000Base-X SFP Port speed LED (yellow)
(9) 10/100/1000Base-X SFP Port connection status LED (green)
(10) 10/100/1000Base-X SFP Port speed LED (yellow)

Structure and Interface
4
(11) 10/100/1000Base-X SFP Slot
(12) 10/100Base-X Ethernet Port
(13) 10/100Base-T(X) Ethernet Port speed LED (yellow)
(14) 10/100Base-T(X) Ethernet Port connection status LED (green)
Medium product front panel
Figure 2 Medium product front panel
(1) Power 1 LED
(2) Power 2 LED
(3) Running LED
(4) Ring LED
(5) Alarm LED
(6) Reset button
(7) 10/100/1000Base-X Port connection status LED (green)
(8) 10/100/1000Base-X SFP Port speed LED (yellow)
(9) 10/100/1000Base-X Port connection status LED (green)
(10) 10/100/1000Base-X SFP Port speed LED (yellow)
(11)10/100/1000Base-X SFP Slot

Structure and Interface
5
(12) 10/100/1000Base-T(X) Ethernet Port
(13) 10/100/1000Base-T(X) Ethernet Port speed LED (yellow)
(14) 10/100/1000Base-T(X) Ethernet Port connection status LED (green)
Large product front panel
Figure 3 Large product front panel
(1) Power 1 LED
(2) Power 2 LED
(3) Running LED
(4) Ring LED
(5) Alarm LED
(6) Reset button
(7) 10/100/1000Base-X SFP Port connection status LED (green)
(8) 10/100/1000Base-X SFP Port speed LED (yellow)
(9) 10/100/1000Base-X SFP Port connection status LED (green)
(10) 10/100/1000Base-X SFP Port speed LED (yellow)
(11) 10/100Base-T(X) or 10/100/1000Base-T(X) Ethernet port speed LED (yellow)
(12) 10/100Base-T(X) or 10/100/1000Base-T(X) Ethernet Port

Structure and Interface
6
(13) 10/100Base-T(X) or 10/100/1000Base-T(X) Ethernet Port connection status LED (green)
(14) 100/1000M SFP Slot
2.2 Top Panel
2.2.1 Low voltage（L2/L5）products Top Panel
Figure 4 Low voltage products Top Panel

Structure and Interface
7
2.2.2 High voltage（HV）products Top Panel
Figure 5 High voltage products Top Panel

Mounting
8
3 Mounting
3.1 Dimension Drawing
Figure 6 Dimensions for Small Products DIN-Rail Mounting (unit: mm)
Figure 7 Dimensions for Small Products Panel Mounting(unit: mm)

Mounting
9
Figure 8 Dimensions for Medium Products DIN-Rail Mounting (unit: mm)
Figure 9 Dimensions for Medium Products Panel Mounting(unit: mm)

Mounting
10
Figure 10 Dimensions for Large Products DIN-Rail Mounting (unit: mm)
Figure 11 Dimensions for Large Products Panel Mounting(unit: mm)
Caution:
As part of the heat dissipation system, the switch housing becomes hot during operation.
Please use caution when coming in contact and avoid covering the switch housing when the
switch is running.
The figures in this manual are only for reference.
3.2 Mounting Modes and Steps
The device supports both DIN-rail mounting and panel mounting. Before installation, make
sure that the following requirements are met.
1) Environment: temperature (-40℃to 75℃), ambient relative humidity (5% to 95%,

Mounting
11
non-condensing)
2) Power requirement: The power input is within the voltage range of the switch.
3) Grounding resistance: <5
4) No direct sunlight, distant from heat source and areas with strong electromagnetic
interference.
5) Devices are to be installed in an authority certified enclosure and accessible only by the
use of a tool.
6) Devices should be installed and accessed by service personnel or users who have been
instructed about the reasons for the restrictions applied to the location and about any
precautions that shall be taken.
3.2.1 DIN-Rail Mounting
DIN-Rail Mounting
Step 1: Select the mounting position for the device and guarantee adequate space and heat
dissipation.
Step 2: Insert the connecting seat onto the top of the DIN rail, and push the bottom of the
device inward and upward to ensure the DIN rail fits in the connecting seat. Make sure the
device is firmly installed on the DIN rail, as shown in the following figure.
Figure 12 DIN-Rail 2 Mounting
DIN-Rail Dismounting
Step 1: Insert the head of a screwdriver into the opening of the spring locking piece at the
bottom from the left. Lift the handle of the screwdriver to open the spring locking piece of the