Laird BL600 Series Installation and operating instructions

BL600 MODULE
Embedded Wireless Solutions Support Center:
http://ews-support.lairdtech.com
www.lairdtech.com/bluetooth
1
Americas: [phone]
Europe: [phone]
Hong Kong: [phone]
WHISPER MODE
Application Note v1.0
INTRODUCTION
The goals of this document include the following:
To explain how to use Laird’s BL600 module in whisper mode pairing.
To test the Whisper Mode functionality through the use of a BT v4.0-enabled iOS device.
OVERVIEW
Security is a critical issue in wireless communication. In Bluetooth Low Energy (BLE), when two devices wish
to communicate securely, Simple Secure Pairing is used. This process establishes a secret link key to correctly
authenticate devices. However, in most cases the pairing process itself is carried out on the same exposed
wireless medium and is therefore still vulnerable to interceptions and attacks.
To enhance security and ease during the pairing process, Laird developed a unique approach which involves
the transmission power being significantly decreased while pairing is in progress. This ensures that pairing is
not completed unless the devices are within a relatively close proximity to each other. This behavior is known
as Whisper Mode Pairing. This proximity-enhanced security adds the extra level of trust that can be used to
authenticate BLE devices. An additional benefit of Whisper Mode is that end users of products that are
implementing Laird’s BL600 can be certain they are connecting to the correct, intended remote device by
simply bringing them into close proximity. Finally, Laird’s whisper mode may decrease footprint and BOM
costs for OEMs by removing requirements for additional wireless technologies, such as Near Field
Communications (NFC); it provides similar attributes from within the BL600 module.
Whisper mode pairing is achieved with the function BleTxPwrWhilePairing(). This function, called once at
startup, sets the transmit power of all packets that are transmitted while pairing is in progress. Radial
measurements have shown that setting the pairing transmit power to -55 creates a ‘bubble’ with a radius of
about 30 cm, outside which pairing will not succeed. This should be decreased even further if the BL600 is
covered by the final product enclosures which affect the radio’s overall RF performance.
REQUIREMENTS
PC running Windows XP or later
UWTerminal 6.50 or later
Sample apps as deployed with the firmware’s zip file and specifically the application stored in the file
“htss.health.thermometer.sensor.SB”
USB A to mini B cable
BL600 devkit with firmware version 1.5.62.0 or later
iOS device with BT4.0 support (e.g. iPad 3/iPhone 4S/iPad mini or newer)
Internet connection on the iOS device (to download the BL600 app)
Note: This application note assumes that you are familiar with how to download smart BASIC applications
onto the BL600 using the UWTerminal utility. If not, refer to the module’s user guide and
specifically to the chapter “ Getting Started ”. You can access the BL600 user guide from the
Embedded Wireless Solutions Support Center:
https://laird-ews-support.desk.com/?b_id=1945#docs

BL600 Whisper Mode
Application Note
Embedded Wireless Solutions Support Center:
http://ews-support.lairdtech.com
www.lairdtech.com/bluetooth
2
Americas: [phone]
Europe: [phone]
Hong Kong: [phone]
CONFIGURING AND LOADING THE SMART BASIC APPLICATION
To configure the smart BASIC application, follow these steps:
1. Open the htss.health.thermometer.sensor.sb application that is located in the supplied
smartBASIC_sample_Apps folder.
2. Navigate to the end of the file, and add the line rc = BleTxPwrWhilePairing(-55) before the WaitEvent
statement (line 341). This function sets the transmitted power to -55 dBm during pairing.
3. Save the smart BASIC application and load it into the BL600 using UWTerminal.
339 OnStartup()
340 rc=StartAds(ADV_IND)
341 rc=BleTxPwrWhilePairing(-55)
342 '//-------------------------------------------------------------------------
343 '// Wait for a synchronous event.
344 '// An application can have multiple <WaitEvent> statements
345 '//-------------------------------------------------------------------------
346 WaitEvent
IOS DEVICE SETUP
To set up the iOS device, follow these steps:
1. Install the BL600 app from the Apple App Store (Figure 1). If you are searching for the application on
an iPad, you may need to click the iPhone Apps tab in the App Store.
BL600 by Laird Technologies: https://itunes.apple.com/gb/app/bl600/id594855763?mt=8
Figure 1: Installed BL600 app
2. Ensure Bluetooth is enabled in the device settings.
3. Once installed, run the BL600 application on your iOS device.
4. Select Sensors > Temperature. (Figure 2)
Figure 2: BL600 App –Home screen, sensors menu, temperature

BL600 Whisper Mode
Application Note
Embedded Wireless Solutions Support Center:
http://ews-support.lairdtech.com
www.lairdtech.com/bluetooth
3
Americas: [phone]
Europe: [phone]
Hong Kong: [phone]
TESTING WHISPER MODE PAIRING
To test whisper mode functionality, follow these steps:
1. Inside UWTerminal, type htss followed by return in the main window to run the application. The
module initialises, advertisements begin, and the log is printed to the console (Figure 3).
Figure 3: UWTerminal showing the htss program starting
2. Press Connect on the iOS device.
Notice that even though a connection occurs (Figure 4), no results display on the iOS device’s screen;
this indicates that it has not paired to the BL600 module.
Figure 4: UWTerminal updated to show that a connection has occurred

BL600 Whisper Mode
Application Note
Embedded Wireless Solutions Support Center:
http://ews-support.lairdtech.com
www.lairdtech.com/bluetooth
4
Americas: [phone]
Europe: [phone]
Hong Kong: [phone]
3. Slowly move the iOS device closer to the module until the pairing request notification pops up (Figure
5). This does not occur unless the devices are a few inches apart. When you press Pair on the iOS
device, the screen updates to show the temperature reading sent by the BL600 module.
Figure 5: The iOS device indicating the pairing process is achieved in close proximity
The completion of the pairing process is also captured by the UWTerminal log screen, which should be
updated to show that an encrypted bonding has occurred and that the two devices have now been
paired. (Figure 6)
Figure 6: UWTerminal updated to show that pairing has occurred
ADDITIONAL INFORMATION
Additional documentation and information relating to firmware is available from the Laird Embedded
Wireless Solutions Support Center: https://laird-ews-support.desk.com/?b_id=1945
… As well as the Laird website at:
http://www.lairdtech.com/products/bl600-series.

BL600 Whisper Mode
Application Note
Embedded Wireless Solutions Support Center:
http://ews-support.lairdtech.com
www.lairdtech.com/bluetooth
5
Americas: [phone]
Europe: [phone]
Hong Kong: [phone]
REVISION HISTORY
Revision
Date
Description
Approved By
1.0
08 Jan 2015
Initial Release
Jonathan Kaye