Landoll Brillion 3630 User manual

Single Point Depth Control
Installation Instructions
for 3630 Pulvi-Mulcher
Kit 197724
®

1 F-826

CAUTION

CAUTION
IMPORTANT
Unfold, lower the unit to the ground, and relieve
hydraulic pressure before attempting to service any
hydraulic component.
1. Remove all Tooth Control Hydraulic Hoses from the
24 port manifold, except the two 3/8 x 234” hoses
that go to the tractor. They will be used for Spike
Drag Hydraulic Lift.
2. Remove the four 4 x 8 Hydraulic Cylinders. One from
each wing and two from the center frame.
3. For proper fit of 4-1/2 x 8 cylinders, remove up 1/2”
material from Frame Plate and Frame Support Plate.
See Figure 1-2.
Installation
To ensure alignment of assemblies, leave the nuts
loose until completion of final assembly. Use lock
washers or flat washers as specified. Spread all cotter
pins.
After completion of final assembly, tighten all nuts
evenly to prevent misalignment, distortion or binding.
Tighten all screws and nuts to the recommended torques.
Refer to operator manual F-752 for general and hydraulic
fittings torque specifications.
1. Install the two new 4 x 8 Rephase Hydraulic
Cylinders on the wings in the same location as the
old.
2. Install the two new 4-1/2 x 8 Rephase Hydraulic
Cylinders on the center frame in the same location as
the old. Center Left Cylinder requires new 1 x 9”, 3
hole pin.
3. With a 1” flat washer on each side of the tooth control
bracket slide 1x 9” pin through with the long hole
spacing first. Secure with 5/16 x 2 roll pin on each
side of the 1” flat washer. See Figure 1-1.
4. Place Depth Control Bracket ahead of the pin on the
Front Roller Frame Asm. Secure with 3/4-10 U-Bolt
and locknut. Install valve and mounting brackets.
5. Assemble the Depth Stop Tube Asm to the 3 hole
pin, spacers, washers. Secure with roll pin. Ensure
the Depth Stop Tube Asm is parallel to the Tooth
Control Tube. See Figure 1-3.
6. Install new hydraulic fittings as shown in Figure 1-4.
7. Connect and route the Hydraulic hoses along the
front frame tube. See Figures 1-5 and 1-6. Run the
hydraulic hoses with the drag lift hoses. Secure with
tie straps. Use hose wrap were designated.
Bleed Air From Hydraulic System
Rephase bleeds in retract. Bleed air by continually
flowing oil after cylinders are retracted.
Refer to operator manual F-752 for proper procedure. As
instructed, always bleed the system whenever hydraulic
circuit is opened for any reason.
Figure 1-1: Depth Control Tube and Pin
Do not work on or under this machine unless
securely blocked and supported by a hoist or
tractor or by other sufficient means.
Strap each tooth section to frame to prevent
unexpected movement when removing cylinders.
Pin,1 x 9
P/N 193216
Roll Pin,5/16 x 2
Flat Washer,1” SAE

F-826 2
Figure 1-2: Center Frame Rework
Figure 1-3: Depth Control Assembly
Rephasing Cylinder,
4-1/2 x 8
Frame Support
Plate
Frame Plate
You may need to grind
up to 1/2” of Frame Plate
and Frame Support Plate
for cylinders to fit properly
on the center frame
Rephasing Cylinder,
4-1/2 x 8
Frame Support
Plate
Frame Plate
3630 OpSinglePtDepthCtrlAdj
Flat Washer,1” SAE
Roll Pin,5/16 x 2
Sleeve
P/N 7K226
P/N 7K723
Pin,1 x 9
P/N 193216
P/N 193207
Depth Control Bracket
P/N 193207
Depth Control Bracket
P/N 193215
P/N 193214
Bolt,5/16-18 x 2
3/8-16
Bolt,
3/8-16 x 1-3/4
Locknut,5/16-18
Depth Slider Support
Depth Valve Mount
Depth Stop Tube Asm
P/N 193206
Flat Washer,1” SAE
Front Roller Frame Asm
U-Bolt,3/4-10
Locknut,3/4-10
Locknut,
Tooth Control
Tube

3F-826
Figure 1-4: Simplified Schematic
3630 SimplifiedToothSchematicSPDC
Limit Valve
Adapter,90°
Adapter,90°
Male Couplers,
3/4-16 O-Ring
Hose Asm,
3/8 x 250”
P/N 175104
Hose Asm,
3/8 x 214”
P/N 145130
Adapter Tee
Adapter,#8 O-Ring
to #8 Tube
Adapter,90°
Hose Asm,
3/8 x 114”
P/N 166171
Hose Asm,
3/8 x 190”
P/N 141883
Hose Asm,
3/8 x 154”
P/N194115
Adapter,90°
Hose Asm,
3/8 x 228”
P/N 71600088
Hyd Cyl,
4-1/2 x 8
Hyd Cyl,
4 x 8
Hyd Cyl,
4 x 8
Hose Asm,
3/8 x 154”
P/N 194115

F-826 4
Figure 1-5: Hydraulic Schematic
Wing Folded
Wing Unfolded
3630 ToothSchematicSPDC
Hose Asm, 3/8 x 228”
Hose Asm, 3/8 x 154”
Hose Asm, 3/8 x 228”
Hose Asm, 3/8 x 114”
Hose Asm, 3/8 x 214”
Hose Asm, 3/8 x 250”
Hose Asm, 3/8 x 228”
Hose Asm, 3/8 x 250”
Hose Asm, 3/8 x 190”
Hose Asm, 3/8 x 114” Hose Asm,
3/8 x 154”
Hose Asm, 3/8 x 190”
Hose Asm, 3/8 x 114” P/N 166171
Hose Asm, 3/8 x 154”
Limit Valve
Adapter,90°
Adapter,90°
Adapter,90°
Adapter Tee
Adapter,#8 O-Ring to #8 Tube
Male Couplers, 3/4-16 O-Ring
Adapter, 90°
Hyd Cyl, 4-1/2 x 8
Hyd Cyl, 4 x 8
Hyd Cyl, 4 x 8
Adapter,90°
Adapter, 90°
P/N 166171
P/N 194115
P/N 141883
P/N194115
P/N 71600088
P/N 175104
P/N 141883
P/N 175104
P/N 145130
P/N 71600088
P/N 194115
P/N 71600088
P/N 166171

5F-826
Figure 1-6: Hydraulic Layout
Wing Folded
Wrap Drag Lift and
Tooth Control (4)Hoses
together near Hinge Pin
with Hose Wrap
Wing Unfolded
Wrap Drag Lift and
Tooth Control (4)Hoses
together near Hinge Pin
with Hose Wrap
3630 ToothLayoutSPDC
All Tread Screw, 3/8-16 x 4-1/2
Nut,3/8-16
Hose Holder Clamp
Wing Nut
Bolt,5/16-18 x 2 P/N 1-654-010049-09
Locknut,5/16-18, P/N 1-512-010005-03
Hose Wrap
Limit Valve, P/N 140693
Hose Asm, 3/8 x 250” P/N 175104
Hose Asm, 3/8 x 228”
Hose Asm, 3/8 x 190”
Hyd Cyl 4-1/2 x 8
Hose Asm, 3/8 x 154”
P/N 194115
Hose Asm, 3/8 x 114”
P/N 166171
Hose Asm, 3/8 x 214” P/N 145130
Hose Asm, 3/8 x 114” P/N 166171
Hose Asm, 3/8 x 154” P/N 194115
Hose Asm, 3/8 x 228” P/N 71600088
Hyd Cyl, 4-1/2 x 8
Hose Asm, 3/8 x 228” P/N 71600088
Hose Asm, 3/8 x 154” P/N 194115
Hyd Cyl, 4 x 8
P/N 71600088
P/N 141883
Hose Wrap
All Tread Screw, 3/8-16 x 5
Hose Clamp P/N 2-181-010001
Flat Washer,3/8
Locknut,3/8-16
Hose Asm, 3/8 x 190” P/N 141883