Landoll Brillion PPD Series Product manual

®
1098rev0813 5K804
LANDOLL CORPORATION
1900 North Street
Marysville, Kansas 66508
[phone]
800-428-5655 ~ WWW.LANDOLL.COM
Pick-up Pulverizer
Operator’s and Parts Manual
PPD Series 10’ through 20’
PPO Series 10’ through 20’

5K804

5K804
Introduction ..................................................................................................................................... 3
Location Reference ................................................................................................................ 3
Parts Ordering ........................................................................................................................ 3
Safety Suggestions ........................................................................................................................ 4
Safety Signs ............................................................................................................................ 4
Safety Sign Location .............................................................................................................. 5
Operating Instructions .................................................................................................................... 6
Warning Light Assembly ................................................................................................................. 7
Tire Track Remover Assembly ....................................................................................................... 8
PPD Model Pulverizers - Machine Specifications .................................................................. 9
Optional Equipment ................................................................................................................ 9
Repair Parts........................................................................................................................ 10
Frame & Roller Assembly - 10’ through 16’ Machines ................................................. 10
Frame & Roller Assembly - 18’ through 20’ Machines ................................................. 12
Three Point Hitch .......................................................................................................... 14
Scrapers........................................................................................................................ 16
Light Kit ......................................................................................................................... 18
Tire Track Remover ...................................................................................................... 19
PPO Model Pulverizers......................................................................................................... 23
Index ...................................................................................................................................... 28
Page I
CONTENTS
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
PICK-UP PULVERIZERS

5K804

5K804
Figure1
Page 3
INTRODUCTION
Your Brillion Pulverizer is built with the best materials and workmanship available. It has been designed
to give years of trouble-free operation. Proper care and operation will insure that you receive the
service and long life built into this machine.
Study this manual carefully before attempting to operate the machine. If items in the manual are not
understood, contact your local Brillion dealer.
This safety alert symbol is used to call your attention to
instructions concerning your personal safety. It is found on your
machine and in this manual. It is important to pay attention to the
precautions indicated and to be alert to the possiblility of personal
injury or death.
Federal law requires you to explain the safety and operating
instructions furnished with this machine to all employees before they
are allowed to operate the machine. These instructions must be
repeated to the employees at the beginning of each season. Be sure
to observe and follow these instructions for your own and your
employee’s safety.
Location Reference
Right hand, left hand, and forward designations are determined by standing behind the machine and
facing the direction it will travel during field operation.
Parts Ordering
When ordering parts for this machine, include the
complete model number and serial number. Refer to the
nameplate located on the right side of the 3-point hitch.
Please read and record this number upon taking delivery
of this machine. See Figure 1.
Pulverizer Model No. _______________________
Serial Number ____________________________
Date Purchased __________________________
Be sure to read the Warranty Form which is provided.
Return the proper portion of the Warranty Form for
recording at the factory.
SAFETY ALERT
SYMBOL

5K804
2
3
Figure 2A
1. DO NOT STAND OR WALK IN FRONT OF TRACTOR WHEN IT IS
MOVING FORWARD.
2. DO NOT STAND OR WALK BETWEEN TRACTOR & IMPLEMENT
WHEN EITHER OR BOTH ARE MOVING.
3. DO NOT STAND OR WALK BEHIND IMPLEMENT WHEN IT IS BEING
BACKED UP.
4. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON TRACTOR OR
IMPLEMENT.
5. BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN UNHITCHED
FROM TRACTOR. 8J309
MOVING MACHINES CAN CAUSE INJURY. KEEP AWAY!
CAUTION 1
1. 8J309 - Decal, “Caution” list
2. 528934 - Decal, Reflective Amber
3. 528933 - Decal, Reflective Red
SAFETY SUGGESTIONS
Investigation has shown that nearly one-third of all farm accidents are caused by careless use of
machinery. You can do your part in improving safety by observing the following suggestions. Insist
that all people working with you or for you abide by them.
1. Do not stand between tractor and implement when attaching or detaching implement, unless neither
are moving.
2. Do not allow anyone to ride on tractor or machine.
3. Lower machine to ground when not in use.
4. Use support stand so that machine will not roll when unhitched from tractor.
5. Do not transport at speeds over 20 MPH.
6. When transporting machine, avoid sudden stops or sharp turns because the weight of the machine
may cause the operator to lose control of the tractor.
7. When transporting the machine on a road or highway, use adequate warning symbols, reflectors,
lights and slow moving vehicle signs as required.
8. Securely block machine when working on or under it to prevent injury in case of hydraulic failure or
inadvertent lowering by another person.
SAFETY WARNING SIGNS
The “WARNING” signs illustrated on this page are placed on the machine to warn of hazards.
“The warnings found on the sign are for your personal safety and those around you.” Their locations
on the machine are shown on the following page. OBSERVE THESE WARNINGS!
Keep these signs clean so they can be observed readily. Wash with soap and water or cleaning
solution as required.
Replace “WARNING” signs should they become damaged, painted over or if they are missing.
When replacing decals, clean the machine surface thoroughly using soap and water or cleaning
solution to remove all dirt and grease.
1098ev401 Page 4

1
5
5
6
2
3
4
1. 8J309 - “Caution” Decal
2. 528938 - Orange Stripe
3. 528933 - Red Reflector
4. 528934 - Yellow Reflector (on frontside of decal plate)
5. 4K103 - Brillion Decal
6. 2P151 - SMV with bracket
Decal Locations
Figure 2B
1098rev0813 Page 5 5K804

5K804
Page 6
OPERATION
Securely block machine when working on or under it to prevent injury in case of hydraulic
failure or inadvertent lowering by another person.
This pulverizer is designed to be mounted to tractors with a category II 3-point hitch. Clevis pins (with
1 1/8” dia.) are provided for attaching to the tractor’s lower links. Fasten to upper tractor link securely
with a 1" pin.
When operating, keep support stand locked up in raised position. To park the pulverizer, lower it to a
level surface; then set and fix the support stand all the way down.
After the first 1 - 2 hours of use, check over all fasteners to insure that they remain tight. Periodic
checks should be made thereafter.
1098ev401

Amber LED Lamp
LED Warning
Lights Harness
Flasher Control
Module
7Pin/4Pin
WP Harness
Red LED Lamp
Amber LED Lamp
When plugging in the LED 7-pin connector:
1) Make sure the tractor has a good clean receptacle, free of dirt and corrosion.
2) Make sure the 7-pin connector is inserted ALL the way in. With tighter fitting pins, operator
may think the connector is all the way in, but really isn’t.
3) Make sure the tractor receptacle cover latches over the keyway on the 7-pin connector to hold
the connector in place.
If an operator plugs in the 7-pin connector, but the lights do not seem to work right, check the above
items to make sure there is a good connection with the 7-pin connector.
1098rev0813 Page 7 5K804

C
L
Light Module
Bracket
Red Lamp Red Lamp
5 7/8”
96”
64”
48”
32”
Light Module
Light Module Bracket
Screw, 1/4-20 X 1-1/2
Locknut, 1/4-20
LED Lamp Placement Dimensions
Light Module and Bracket
1098rev0813 Page 7A 5K804

LED Lamp and Harness Installation
1. Install the inner Light Brackets on the frame tube, approximately 32” from the center of the
frame. Place a Strap under the frame and secure Light Brackets with 1/2-13 X 7-1/2 Screws,
Washers and Locknuts. See pages 7A and 7C.
2. Install the outer Light Brackets on the frame tube using existing Bearing Hanger Hardware.
3. Place the Amber LED’s inside the Light Shields and attach to the outer Light Bracket using 1/4-
20 X 1-3/4 Screws, then attach the Decal Plate to the opposite side of the Light Bracket and
secure with Washers and Locknuts.
4. Attach the Red LED’s to the inner Light Brackets using 1/4-20 X 1-1/2 Screws, then attach the
Decal Plate to the opposite side of the Light Bracket and secure with Washers and Locknuts.
5. Install the Light Module under the Light Module Bracket using two 1/4-20 X 1-1/2 Screws and
Locknuts. Then attach the Light Module Bracket to the frame approximately 5 7/8” right of the center of the
frame using 1/2-13 X 7-1/2 Screws, Washers and Locknuts. See page 7A
6. Attach the 7 pin harness to the Light Module. Route the harness along the frame and to the
front of the 3 point Hitch.
7. Layout the LED Lamp Harness. Note that the cords are marked “Left” and “Right”.
Attach the harness to the Light Module.
8. Route the left 2 plug cord along the top of the left side frame, going through both Light
Brackets. Attach the cord into the Amber LED, repeat for the right side.
9. Route the left 3 plug cord along the top of the left side frame, through the Red LED Light
Bracket. Attach the cord into the Red LED, repeat for the right side.
10. Secure both harnesses with tie straps, making sure to leave enough slack to allow the
machine to raise and lower. Bundle and secure any excess cord with tie straps.
11. Raise and lower machine to check for proper clearance, adjust accordingly.
Important: All wires must be firmly attached to machine frame members, so they don’t sag or
become torn loose by field debris. Use the cable and hose ties provided.
1098rev0813 Page 7B 5K804

Screw,1/4-20 X 1-3/4 Light
Shield Light
Bracket
Decal Plate
Amber
LED
Screw,
1/4-20 X 1-1/2
Red
LED
Strap
Screw,
1/2-13 X 7-1/2
Locknut,1/2-13
SMV
Washer,1/2
Screw,5/16-18 X 3/4
Locknut,
5/16-18
7 Pin
Harness
Screw,
1/4-20 X 1-1/2
Locknut,1/4-20
Light Module Bracket
Light
Module
Lamp
Harness
Washer,5/8
Locknut,1/2-13
Screw,
5/8-11 X 8
Lock Washer,5/8
Nut,5/8-11
Washer,1/4
LED Warning Light Installation
1098rev0813 Page 7C 5K804
Lock Washer,5/8
Locknut,5/8-11

ASSEMBLY OF THE 5K977 TIRE TRACK REMOVER KIT
S-Tine
Bracket
Tooth Bar
Tube
Channel
Adapter
5” Strap
8” Strap
Duckfoot
Point
Reversible
Point
Screw
½”-13 X 6”
Screw
½”-13 X 8”
Screw
½”-13 X 1½”
½” Lockwasher
½”-13
Hex Nut
Clamp
7/16”-14
Lock Nut
Screw
7/16”-14 X 3 ½”
3/8”-16
Flange Nut
Cultivator
Bolt
Centered behind each tractor tire, attach a set of Channel Adapters to the Pulverizer frame using the 8” Straps and
½” X 8” Bolts, Lockwashers, and Hex Nuts. Ensure that the Channel Adapter end with four holes is downward.
Prior to inserting the bottom 8” Bolts line up the S-Tine bracket with the four lower holes on the Channel Adapter.
Attach with 8” Bolts and Hex Nuts. The 1 ½ Screws, Lockwashers and Nuts are inserted in the two bottom holes.
Tighten all fasteners at this time.
Attach Tooth bar Tubes to the S-Tine Brackets using 5” Straps and ½” X 6” Bolts, Lockwashers, and Nuts. Tighten
all fasteners at this time.
Locate and install S-Tines as needed to cover tractor tire tracks.
Attach the Duckfoot and Reversible Points to the S-Tines using the Cultivator Bolts and 3/8” Flange Nuts. The
suggested pattern is to use the Reversible Point on center tine and Duckfoot Points on each side. If needed,
additional tines may be purchased and installed.
Check for interference between tractor tires and S-Tines. If this occurs, the Tooth Bar Tubes can be mounted
behind rearmost vertical member on the S-Tine brackets.
1098rev1212 Page 8 5K804

5K804
MACHINE SPECIFICATIONS
(Subject to Change without Notification)
Model Designation:
Basic model is denoted by “PPD” - Pickup Pulverizer with Ductile wheels.
The number following indicates the rolling width.
(example: PPD10 - 10’ Pickup Pulverizer with ductile wheels)
Basic Machine Specifications:
Rolling Transport No. 20” Ductile Axle Approximate
Model Width Width Wheels Wheel Style Size Weight (Lbs.)
PPD-10 10’ 11’ 30 8J001 4” 1568
PPD-12 12’ 13’ 2” 36 8J001 4” 1792
PPD-14 14’ 15’ 2” 42 8J001 4” 2016
PPD-16 16’ 17’ 2” 48 8J001 4” 2386
PPD-18 18’ 19’ 2” 54 9J808 4 1/2” 2769
PPD-20 20’ 21’ 2” 60 9J808 4 1/2” 3026
Frame: 3/8” Wall Tubing
Hitch: Category II 3 Point
OPTIONAL EQUIPMENT
Scraper Kits:
5K753 for PPD-10 .......................................................................................................... 121#
5K754 for PPD-12 .......................................................................................................... 137#
5K755 for PPD-14 .......................................................................................................... 152#
5K756 for PPD-16 .......................................................................................................... 168#
5K757 for PPD-18 .......................................................................................................... 196#
5K758 for PPD-20 .......................................................................................................... 212#
5K977 Tire Track Remover Kit ...................................................................................................213#
Page 9
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
PPD PULVERIZERS
1098rev401

Table provided for general use.
NOTES:

5K804
34
16
21
36
28
8
6
4
3
5
6
9
7
12, 13
19, 31
34
26
32
12, 13
26
12 13 10
18
17
20
12,13
15
24
29
25
35 30
35
29
28
30
33
1
32
6
4
35
6
2
12, 13
28
27
11
19, 31
22
23
Page 10
1098ev401
CAUTION
MOVING MACHINES CAN CAUSE INJURY. KEEP AWAY!
1. KEEP AWAY FROM MOVING TRACTORS OR IMPLEMENTS.
KEEP OTHERS AWAY.
2. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON TRACTOR
OR IMPLEMENT.
3. BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN
UNHITCHED FROM TRACTOR.
4. KEEP ALL GUARDS AND SHIELDS IN PLACE WHILE
MACHINE OR PARTS ARE IN MOTION. 8J309

5K804
FRAME & ROLLER ASSEMBLY
MACHINESWITH4"OUTSIDEDIAMETERPIPEAXLE(10’thru16’Machines)
Index
No. Part # Description Qty. Weight (lbs.)
1 5K726 Frame Tube, 10’ 1 306.9
5K727 Frame Tube, 12’ 1 361.8
5K728 Frame Tube, 14’ 1 416.8
5K729 Frame Tube, 16’ 1 471.7
2 9J028 Wheel and Axle Assembly (10’ Machines) 2 485.0
8J069 Wheel and Axle Assembly (12’ Machines) 2 599.0
8J068 Wheel and Axle Assembly (14’ Machines) 2 671.0
9J027 Wheel and Axle Assembly (16’ Machines) 2 788.0
3 9C062 Pipe Axle Assembly, 10’ w/ bearings 2 60.0
8C986 Pipe Axle Assembly, 12’ w/ bearings 2 69.0
1D138 Pipe Axle Assembly, 14’ w/ bearings 2 78.0
3D199 Pipe Axle Assembly, 16’ w/ bearings 2 87.0
4 9C014 Outer Bearing Housing 2 8.7
5 9C015 Inner Bearing Housing 2 9.7
6 9C016 Bearing 4 1.7
7 8J001 Wheel, 20” Ductile Notched 30, 36, 42, 48 28.0
8 9J277 Spacer Ring 4 .2
9 9C031 Axle Clamp, 4” 2 3.7
10 9D673 U-Bolt, 1/2” 2 .7
11 2D535 Set Screw, 1/2” 4 -
12 1C109 Lockwasher, 1/2” 22 -
13 1C390 Nut, 1/2” 22 -
- 8J998 L.H. End Bracket Assembly (items 15-20) 1 15.0
15 8J996 L.H. End Bracket 1 13.5
16 9D669 Straight Axle Mount 4 .9
17 4D529 Slotted Nut 3 .1
18 2C864 Cotter Pin 3 -
19 1B166 Lockwasher 11 -
20 9D864 Drilled Bolt, 3 1/2” Long 2 .9
- 8J999 R.H. End Bracket Assembly (items 21 & 16-20) 1 15.0
21 8J997 R.H. End Bracket 1 13.5
- 8J993 Center Bracket Assembly (items 22, 23 & 16-19) 1 22.0
22 8J994 Center Bracket 1 14.0
23 9D866 Drilled Bolt, 6” Long 1 .6
24 3K318 Angle 2 5.4
25 1J696 Bolt, 1/2” x 7 1/2” 4 .4
26 8C527 Capscrew, 1/2” x 1 1/2” 8 .1
27 8J099 Angle 4 5.3
28 3K321 Strap 6 2.8
29 3K320 Strap 2 1.7
30 7D040 Bolt, 5/8” x 8” 8 .8
31 1C392 Nut, 5/8” Hex 8 .1
32 5D051 Capscrew, 1/2” x 1 3/4” 6 .1
33 8J309 Decal, Caution List 1 -
34 2J430 Decal, Red Reflective 2 -
35 2J431 Decal, Amber Reflective 2 -
36 4K103 Decal, Brillion (2 3/4” x 16 3/4”) 4 -
Page11
1098rev10-13-05

5K804
13
14
8
10, 11
27
29
26
21, 30
31
16
20
32, 33
19
4
25
5
6
22
4
6
5
3
23
35
15
3
36
31 25
24
29
27
28
36
35
1
34
37
32, 33
21,30
23
7
2
32, 33
32, 33
32, 33
31
Page 12
1098ev401
CAUTION
MOVING MACHINES CAN CAUSE INJURY. KEEP AWAY!
1. KEEP AWAY FROM MOVING TRACTORS OR IMPLEMENTS.
KEEP OTHERS AWAY.
2. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON TRACTOR
OR IMPLEMENT.
3. BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN
UNHITCHED FROM TRACTOR.
4. KEEP ALL GUARDS AND SHIELDS IN PLACE WHILE
MACHINE OR PARTS ARE IN MOTION. 8J309
15
9

5K804
FRAME & ROLLER ASSEMBLY
MACHINESWITH41/2"OUTSIDEDIAMETERPIPEAXLE(18’thru20’Machines)
Index
No. Part # Description Used Weight
1 5K730 Frame Tube, 18’ 1 531.3
5K731 Frame Tube, 20’ 1 586.2
2 3K323 Wheel and Axle Assembly (18’ Machines) 2 932.0
5K744 Wheel and Axle Assembly (20’ Machines) 2 1033.0
3 3J186 Shaft Assembly, 18’ Machines 2 139.0
3J185 Shaft Assembly, 20’ Machines 2 151.9
4 9C129 Stub Shaft Mounting 2 13.54
5 5D038 Inner Bearing Housing 2 10.3
6 9C016 Bearing 4 1.7
7 9J808 Wheel, 20” Ductile Notched 24, 30 28.0
8 0A087 Axle Clamp, 4 1/2” 2 3.7
9 1C290 U-Bolt, 7/16” 2 .7
10 1C314 Lockwasher, 7/16” 22 -
11 1C179 Nut, 7/16” 22 -
12 2J417 Bearing [2J516] and Housing [2J515] 2 4.7
13 2J516 Bearing 2 2.2
14 2J515 Bearing Housing 2 2.5
15 9J004 Plate 2 13.5
16 9J007 Center Bracket Assembly 1 22.0
17 9J006 Center Bracket 1 14.0
18 9D669 Straight Axle Mount 4 .9
19 4D529 Slotted Nut 3 .1
20 2C864 Cotter Pin 3 -
21 1B166 Lockwasher 11 -
22 3J860 Drilled Bolt, 2 .9
23 3K318 Angle 2 5.4
24 1J696 Bolt, 1/2” x 7 1/2” 4 .4
25 8C527 Capscrew, 1/2” x 1 1/2” 8 .1
26 8J099 Angle 4 5.3
27 3K321 Strap 6 2.8
28 3K320 Strap 2 1.7
29 7D040 Bolt, 5/8” x 8” 8 .8
30 1C392 Nut, 5/8” Hex 8 .1
31 5D051 Capscrew, 1/2” x 1 3/4” 6 .1
32 1C109 Lockwasher, 1/2” 26 -
33 1C390 Nut, 1/2” Hex 26 -
34 8J309 Decal, Caution List 1 -
35 2J430 Decal, Red Reflective 2 -
36 2J431 Decal, Amber Reflective 2 -
37 4K103 Decal, Brillion (2 3/4” x 16 3/4”) 4 -
Page 13
1098rev10-13-05