Lanpro LP-1522 User manual

Wireless - Equipment
www.lanpro.com
123 Manual, LP-1522 Broadband Wireless AP/Router
WISP Installation Mode.
LP1522_M123_ENG02W
123 Manual, LP-1522
Broadband Wireless AP/Router
WISP Installation Mode.

www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
WISP Installation Mode.
2
Check box contentment, as it is shown in gure 1.
Figure 1
1
Screw the antenna as you can see in gure 2-1 y 2-2;
in case of having an antenna with pigtail type cable,
remember that this must be connected in the other side.
Figure 2-1
2
Connect your PC or Switch to a LAN port of your LP-
1522, as it is shown in gure 3-1. In case you want to
feed it though PoE option, please connect the cable to your
LP-Poe150 Power+Data port as it is shown in gure 3-2;
remember that the cable length recommended is maximum
60m. Then, connect a cable from Data in port of your
LP-PoE150 to your PC or Switch as shown in gure 3-3.
Figure 3-1
3
Figure 2-2
Figure 3-2
Figure 3-3
This type of operation is used in the case you want to connect wireless to an Internet provider. Wireless connection will be
the equipment WAN port and the wire ports will be connections to clients.
In case you want to connect additional clients to your network, you must connect an additional device and set it up AP
mode. As well, we have to mention that all rewall operations will be transfered to wireless connection, having segmentation
between wire and wireless networks; which means separating them in a logic manner.

www.lanpro.com
3
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
WISP Installation Mode.
Connect the DC electrical power plug to the power jack
as shown in gure 4-1; do not forget that this device can
be also powered through PoE with the LP-Poe150 (not
included). If used, please connect the LP-Poe150 to the
mains as it is shown in gure 4-2.
Figure 4-1
4
Figure 4-2
Go to the Local Area Connection Properties window of
your network card (shown in gure 5) and select: Internet
Protocol, then: Properties.
5
In the window of gure 6, please select: Use the following
IP address, and then input an IP address in the range of
IP address by default of the LP-1522. In this example, we
have selected the following address: 192.168.1.201. The
LP-1522 default address is: 192.168.1.254. Now, input in
Subnet mask 255.255.255.0. In Default gateway input
the destination router address. In DNS, input DNS address
of your ISP or destination router address that supplies
Internet service, this is for any queries that need to be sent
to the destination router. You might also use the option:
Obtain an IP address automatically, always when DHCP
Server of your LP-1522 is enabled.
Once you have nished, click: OK, then: OK again, and
then: Close.
6
Figure 5
Figure 6

www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
WISP Installation Mode.
4
Open your selected browser and enter IP address by default 192.168.1.254, as it is shown in gure 7.
7
Figure 7
In the window shown in gure 8, please, select: Operation
Mode, select: Wireless ISP, select: Apply Change.
8
Figure 8
Click: OK in the window shown in gure 9.
9
Figure 9
In the window shown in gure 10, please, select: Wireless,
Basic Settings, in: Mode, select: Client, then select
Apply Changes, the equipment will restart.
10
Figure 10

www.lanpro.com
5
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
WISP Installation Mode.
Then, in the window shown in gure 11, select: TCP/IP
Settings, WAN Interface and set up you ISP properties,
please remember that in this mode you are turning the
wireless port into a WAN port of your equipment.
11
Figure 11
Now you will congure wireless connection security towards
your service provider. In case of not having a wireless
security provider, skip this step. Otherwise, refer to the
window shown in gure 12, select: Wireless – Security
and then input your security provider data; nally, click on
Apply Changes and then OK. The equipment will restart.
12
Figure 12
Proceed to connect for rst time to the service provider. For
this, in the windows shown in gure 13, select: Wireless,
select: Connect, in case that the network, you wish to
connect to, does not appear, please, click on Refresh until
it is shown.
13
Figure 13

www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
WISP Installation Mode.
6
You will receive a message: Connect Successfully, shown
in gure 14. In that window, click OK. In case that it does
not get connected, please, check security options. It is very
important to know that connection will occur automatically,
even when the equipment is unplug and then plug back to
electrical power.
14
Figure 14
Important Recommendation (Optional)
See window shown in gure 15
Proceed to change the administrative password of your
equipment. In other to do this, please select: Management,
then: Password, input the user name which is Admin, and
then type the new password in: New Password and again
in Conrmed Password. Finally, click on Apply Changes.
In other to access to your equipment again, you must input
these data.
15
Figure 15