Lanpro LP-1540ai User manual

Wireless – Equipment
www.lanpro.com
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
LP1540ai_M123_ENB01W
123 Manual, LP-1540ai
High Powered 300 Mbps Access Point
for the 2.4 GHz WiFi band
for Outdoor service, PoE powered
with Múltiple Physical and Virtual interfaces
that supports VLAN and has an EIRP
of 27dBm(0.5W).
Template up-loading.

www.lanpro.com
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
2
1
2
Please check the package contents which
should contain:
a. One LP-1540ai Access Point
b. One PoE adapter with 110V to 220V input
and 12V DC output
c. One Patch Cord as shown in gure 1
In this 123 Manual we will explain how to perform the update of the different operational modes. For other options, please
consult the available 123 Manuals in our site: www.lanpro.com. Please proceed to physically connect the equipment as
per the chosen conguration shown in gures 2.1, 2.2, 2.3 and 2.4.
Figure 1
Figure 2.1
Figure 2.3
Figure 2.2
Internet
Internet
Figure 2.4

www.lanpro.com
3
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
3
4
5
6 7
Please proceed to remove the base as shown in
gure 3 in order to start the installation.
Fix the equipment on the selected location, as shown in gure 4.
You must decide how to power the LP-1540ai, via the AC mains power supply or through the PoE option.
IMPORTANT
Do not powering the equipment through both ways because can be damaged.
Remember that a network connection and AC mains should be available at the location where the LP-1540 is going to be
installed or the network plus PoE power circuit connection.
Figure 3
Figure 4
Proceed to connect the LP-1540ai as shown in paragraph
number 4. Once connected, please proceed to congure it.
Connect the PC or Laptop to the data network where the
LP1540ai is connected, as shown in gures 2.1, 2.2, 2.3
and 2.4

www.lanpro.com
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
4
Go to the Network Card Properties window as shown in
gure 5.
Please input an IP address located in the LP-1540ai segment, the
LP-1540ai has a default IP of 192.168.1.1. Due to this, we will use
in our network card in this example the IP address: 192.168.1.2.
Please remember that there shall be no repeated addresses
in the network. Now proceed to select OK two times, as shown in
Figure 7.
Please proceed to open the browser of your choice and input the default IP address of the LP-1540ai, in this case:
192.168.1.1, as shown in gure 8.
Please select the TCP/IP protocol, select again Properties
as shown in gure 6
89
10
11
Figure 5 Figure 6
Figure 7
Figure 8

www.lanpro.com
5
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
The LP-1540ai, will ask for your
credentials in order to have Access
to its conguration. In this case,
the defaults are: User name:
admin y Password: admin, then
select Login as shown in Figure 9.
Please select option System. Please
see gure 10.
Please select Backup/Flash
Firmware, then select Restore
Backup (choose le) as shown in
gure 11.
12
13
14
Figure 9
Figure 10
Figure 11

www.lanpro.com
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
6
Please explore the Templates folder
and select the desired one, then select
Open, as shown in gure 12.
Proceed to select option Upload
archive, as shown in gure 13.
The equipment will proceed to upload the template values and re-start the equipment, as shown in gure 14, please wait
until the equipment asks again for your credential.
15
16
17
Figure 12
Figure 13
Figure 14

www.lanpro.com
7
123 Manual, LP-1540ai High Powered 300 Mbps Access Point for the 2.4 GHz WiFi band
for Outdoor service, PoE powered with Múltiple Physical and Virtual interfaces that supports VLAN
and has an EIRP of 27dBm(0.5W). Template up-loading.
The equipment will ask again for your
credential as shown in gure 15.
Notes
• All templates have a le containing the description of the values.
• A le containing Notes with the application details is also included.
• All the templates can be modied as per your needs.
• The Default Keys for validation are: User: admin, key: admin.
• The wireless key is: 1234567890 by default.
• All the Templates come with a conguration diagram.
15
Figure 15
LanPro is continuously improving its products and reserves the right to change
specications and availability without prior notice.