Lanpro LP-289ai Instruction sheet

Wireless - Equipment
www.lanpro.com
LP-289ai 123 Conguration Manual in Client Mode.
LP289ai_M123_ENB02W
LP-289ai
123 Conguration Manual
in Client Mode.

www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-289ai 123 Conguration Manual in Client Mode
2
This manual will help you congure the LP-289ai in Client Mode.
Figure 1
1 2
3
Once the 123 Setup Manual is executed, you can proceed
to congure the equipment by rst connecting the cable
included in the box with the LP-289ai to the port: To Odu
located in the PoE injector supplied as shown in gure 1.
Connect the port: To Ethernet to the switch or PC as
shown in gure 2.
Figure 2
4
Connect power to the PoE as shown in gure 3. Please go to your NIC Card properties and select:
Internet Protocol, then select: Properties, as shown in
the window of gure 4.
Figure 3
Figure 4

www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-289ai 123 Conguration Manual in Client Mode
3
5
In the window shown in gure 5, select: Use the following IP address and next, input a IP address in the default
range of the LP-289ai. In this example, we have selected address 192.168.1.201, the LP-289ai has a default address of
192.168.1.1, input now in: Subnet mask 255.255.255.0 and in the: Default gateway the destination router address;
in the: DNS you should input your Service provider´s DNS or the destination router IP address which will provide you
with internet service, this will permit any queries to reach the router of the destination network.
Figure 5
6 7
Open your preferred browser and input the default
address: 192.168.1.1, please see gure 6.
In the certicate validation window shown in gure 7,
accept to continue to website.
Figure 6
Figure 7

www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-289ai 123 Conguration Manual in Client Mode
4
8
In the window shown in gure 8, in: Name input:
admin and in: Password, input: password.
Figure 8
9
In the window shown in gure 9, proceed to change
the equipment’s IP, in this example, the LP-289ai
is going to be a Client of another LP-289ai whose
IP address is: 192.168.1.1 and has more than one
VAP already congured. In order to change the
IP, proceed to select: IP Settings , in the menu:
System Setup, change the IP address and select:
Apply. The equipment will reboot and you will have
to access it with the new IP address.
Figure 9
10
In the window shown in gure 10, proceed to select:
Basic Settings, in the menu: Wireless Setup, in:
operation mode select: Station Adapter and then
select: Apply.
Figure 10

www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-289ai 123 Conguration Manual in Client Mode
5
11
In the window shown in gure 11, in the menu:
Tools, proceed to select: Site survey, locate the
network you wish to connect to, then select it and
click on: select.
Figure 11
12
The selected one will be highlighted as shown in
gure 12.
Figure 12
13
In the window of gure 13, you should congure the
security, this will deppend on the security stablished
already for the AP to which you will connect, in this
example is WEP. In the menú: Wireless Setup,
select: VAP-VLAN Settings, select: sta_prole
then select: Edit.
Figure 13

www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-289ai 123 Conguration Manual in Client Mode
14
In this example we will generate the same keys used
in the AP and will stablish the same authentication and
encryption mode. In order to do this, we must select
in gure 14, in authentication mode by selecting:
Shared key and in encryption: 64 bits WEP, we will
input the passphrase used in the AP and next select:
Generate keys. With this procedure the same keys
will be generated for the Client LP-289ai. Then we
will select Key 1 which is active in the AP and nally
select: Apply.
Figure 14
15
In this case a message will pop-up, shown in gure
15 with the information indicating that the keys apply
to all security , then select: OK.
Figure 15
16
Wait for 30 seconds and verify the connectivity of the equipment. In order to do this you can:
Figure 16 a
aSend a Ping to the destination AP , see gure 16a.
6

www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-289ai 123 Conguration Manual in Client Mode
Figure 16 b
bEnter the AP and verify option: connections that the Client LP-289ai is already connected, see gure 16b.
17
In the window of gure 17, proceed to change the
administration password. Even though it is not mandatory,
we highly recommend it. Please take the precaution to
save it in a safe place because if you lose it you will have
to take the equipment to factory values by opening the
equipment, in which case you lose the warranty. In order
to change the password, select option: change password
in the menu: Management, as shown next.
Figure 17
18
In the window shown in gure 18, input in: Current
Password the old one and in: New Password the new
password, repeat it in the eld: Repeat New Password
then select: Apply.
Figure 18
7