Lanpro LP-C290N User manual

Wireless - Equipment
www.lanpro.com
123 Manual LP-C290N 300 Mbps Wi-Fi Access Point (AP).
Configuration as a Universal Repeater
LPC290N_M123_END01W
123 Manual
LP-C290N 300 Mbps Wi-Fi Access Point (AP).
Configuration as a Universal Repeater
1
Figure 1
Please check the package contents, it must contain the components shown in gure 1
a. One (1) model: LP-C290N
AP equipment
b. One (1) 110VAC-12VDC
power adaptor
c. One (1) Patch-Cord
d. Installation Guide

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
2
4
2
3
This manual explains the conguration steps for Client Mode, (inside the blue frame). It is tied to an LP-C290N working
as an AP connected to an ADSL Modem. For other operation modes, please consult the other 1 2 3 Manuals available for
download at www.lanpro.com. Please see gure 2 and remember that in this conguration, the existence of a WLAN is
mandatory, as shown in gure 2 inside the red frame.
For xation of the equipment on a wall or ceiling, proceed to
remove the base by turning it as shown in gure 3.
Fix it on the selected place
as shown in gure 4
Figure 3
Figure 2
Figure 4
ADSL
Modem LP-SW511
AC
Power
AC Power
Internet
DHCP Client
DHCP Client DHCP
Client
DHCP
Client
LP-C290N
Mode: AP
IP: 192.168.1.1
Mask 255.255.255.0
SSID LanPro LP-C290N
WPA-WPA2-PSK Security
LP-C290N
IP: 192.168.1.2
Universal Repeater Mode
SSID LanPro LP-C290N
IP Computer 192.168.1.3

www.lanpro.com
3
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
5
6
7
8
9
You must decide how to power the el LP-C290N, be it from the AC Mains with the furnished power adaptor or through the
Ethernet cable by using a PoE PSD device.
NOTE: Please be careful and avoid powering the device through both ways at the same time as you will provoke
an internal short circuit that can damage the equipment.
Remember to have an AC mains outlet near the device when powering it with the AC/DC adaptor, or by providing a PSD
device complying with the IEEE 802.3 af standard at the other end of the Ethernet cable supplying data+power.
Figure 5
Figure 6
LP-SW902FGP LP-C290N
Computer LP-C2
9
0N
With PoE
With
Power Adaptor
Connect a PC or Laptop to the LAN where the LP-C290N is located, as shown in gure 6
Once connected, please proceed to its conguration.
Proceed to connect it and to x the base as shown in point Number 4.

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
4
12
13
Figure 9
Figure 10
10 11
Figure 8Figure 7
Now go to your Network Card properties, as
shown in gure 7.
Select the TCP/IP protocol
and properties again as
shown in gure 8.
Assign an IP address inside the LP-C290N segment to your
Network Card. The LP-C290N has a default IP address
of 192.168.1.1, hence, we will use a different one in our
network card like: 192.168.1.3; please see Figure 2 in the
Blue frame, and remember that IP addresses cannot be
repeated in your network. Proceed to select OK twice as
shown in gure 9.
Proceed to open your preferred browser and with the LP-C290N IP address. In this case, use the default address 192.168.1.1,
as shown in Figure 10.

www.lanpro.com
5
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
14
15
16
Proceed to validate the administration IP of your LP-C290N in your diagram, remember that in this case the LP-C290N is a
client of a network, and a router or ADSL modem should be there, responsible for delivering IP addresses to the connecting
Clients. In this example, the Client will has the following address: 192.168.1.3 as shown in gure 11 , remember that your
network card has the following address 192.168.1.3 , please see the blue frame in Figure 2.
The LP-C290N, will prompt for your credentials for accessing your
conguration, in this case use the default ones: User name: admin
y Password: admin, as shown in gure 11
Figure 11
Figure 12
Select the Network / IP Address(UPNP)
option; once the IP has been changed, select
Apply, your equipment will reset and must be
accessed from now on with the new address. In
this case 192.168.1.2 , because it is the second
equipment. Please see Figure 12

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
6
17
18
19
Proceed to change the operation mode to
Universal Repeater by selecting Operation
Mode/ Universal Repeater / Apply, as
shown in gure 15.
Figure 14
Figure 15
Figure 13
Proceed to open your preferred browser and input the new address 192.168.1.2, as shown in Figure 13
The LP-C290N, will prompt for your credentials for accessing your
conguration, in this case use the default ones: User name: admin y
Password: admin, as shown in gure 14

www.lanpro.com
7
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
20
21
22
The equipment will show the counter while the
reset takes place as shown in gure 16.
Proceed to select the network to connect to, in
this example LanPro LP-C290N. Input the
password in the eld named Pass Phrase y
select Connect, as shown in gure 17
The equipment will show the counter while the
reset takes place as shown in gure 18
Figure 16
Figure 17
Figure 18

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Universal Repeater
8
The status window in which you will be able
to conrm that you are connected pops-up, as
shown in the red frame of gure 19.
Proceed to change the password of the
LP-C290N, we highly recommend this. This
password will let you access as an administrator,
to perform this, please select: Management/
Language(Time) and input it in the Password
eld and immediately select Apply, as shown in
gure 20.
Figure 19
Figure 20
23
24
LanPro is continuously improving its products and reserves the right to change
specications and availability without prior notice.