Lanpro LP-C290N User manual

Wireless - Equipment
www.lanpro.com
123 Manual LP-C290N 300 Mbps Wi-Fi Access Point (AP).
Conguration as a Client
LPC290N_M123_ENC01W
LP-C290N
123 Manual LP-C290N 300 Mbps Wi-Fi
Access Point (AP). Conguration as a Client
1
Please check the package contents, it must contain the components shown in gure 1
a. One(1) model: LP-C290N
AP equipment
b. One (1) 110VAC-12VDC
power adaptor
c. One (1) Patch-Cord
d. Installation Guide
Figure 1

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
2
Modem
ADSL
DHCP Server
LP-SW511
LP-C290N
Mode: AP
IP: 192.168.1.1
Mask 255.255.255.0
SSID LanPro LP-C290N
WPA-WPA-PSK Security
AC Powered
Client Mode
IP: 192.168.1.2
Mask 255.255.255.0
AC Powered AP
Using ADSL Modem
AC
Power
AC
Power
L
P-
C
2
90
N
Mk255 255 255
0
Mask 255 255 255
0
Mask
255
.
255
.
255
.
0
Internet
Computer
IP 192.168.1.3
4
2
3
This manual explains the conguration steps for Client Mode, (inside the blue frame). It is tied to an LP-C290N working
as an AP connected to an ADSL Modem. For other operation modes, please consult the other 1 2 3 Manuals available for
download at www.lanpro.com. Please see gure 2 and remember that in this conguration, the existence of a WLAN is
mandatory, as shown in gure 2 inside the red frame.
For xation of the equipment on a wall or ceiling, proceed to
remove the base by turning it as shown in gure 3.
Fix it on the selected place
as shown in gure 4.
Figure 3
Figure 2
Figure 4

www.lanpro.com
3
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
5
6
7
8
9
You must decide how to power the el LP-C290N, be it from the AC Mains with the furnished power adaptor or through the
Ethernet cable by using a PoE PSD device.
NOTE: Please be careful and avoid powering the device through both ways at the same time as you will provoke
an internal short circuit that can damage the equipment.
Remember to have an AC mains outlet near the device when powering it with the AC/DC adaptor, or by providing a PSD
device complying with the IEEE 802.3 af standard at the other end of the Ethernet cable supplying data+power.
Figure 5
Figure 6
Connect a PC or Laptop to the LAN where the LP-C290N is located, as shown in gure 6
Once connected, please proceed to its conguration.
LP-SW902FGP LP-C290N
Computer LP-C2
9
0N
Proceed to connect it and to x the base as shown in point Number 4.
With PoEWith
Power Adaptor

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
4
12
13
Assign an IP address inside the LP-C290N segment
to your Network Card. The LP-C290N has a default IP
address of 192.168.1.1, hence, we will use a different
one in our network card like: 192.168.1.3; please see
Figure 2 in the Blue frame, and remember that IP
addresses cannot be repeated in your network. Proceed
to select OK twice as shown in gure 9.
Proceed to open your preferred browser and with the LP-C290N IP address. In this case, use the default address 192.168.1.1,
as shown in Figure 10.
Figure 9
Figure 10
10 11
Now go to your Network Card properties, as
shown in gure 7.
Select the TCP/IP protocol
and properties again as
shown in gure 8.
Figure 8Figure 7

www.lanpro.com
5
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
14
15
16
Proceed to open your preferred browser and input the new address 192.168.1.2, as shown in gure 13.
Proceed to validate the administration IP of your
LP-C290N in your diagram, remember that in
this case the LP-C290N is a client of a network,
and a router or ADSL modem should be there,
responsible for delivering IP addresses to the
connecting Clients. In this example, the Client
will have the following address: 192.168.1.3 as
shown in gure 11 , remember that your network
card has the following address 192.168.1.3,
please see the blue frame in Figure 2.
Select the Network / IP Address (UPNP)
option; once the IP has been changed, select
Apply, your equipment will reset and must be
accessed from now on with the new address. In
this case 192.168.1.2, because it is the second
equipment. Please see Figure 12.
The LP-C290N, will prompt for your credentials for accessing your
conguration, in this case use the default ones: User name: admin
y Password: admin, as shown in gure 11.
Figure 11
Figure 12
Figure 13

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
6
17
18
19
The LP-C290N, will prompt for your credentials for accessing
your conguration, in this case use the default ones: User
name: admin y Password: admin, as shown in gure 13.
Proceed to change the operation mode to Client
by selecting Operation Mode/AP Client/
Apply, as shown in gure 15.
The equipment will show the counter while the
reset takes place as shown in gure 16.
Figure 14
Figure 15
Figura 16

www.lanpro.com
7
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
20
21
22
Proceed to select the network to connect to,
in this example LanPro LP-C290N, input the
password in the eld named Pass Phrase y
select Connect, as shown in gure 17.
The equipment will show the counter while the
reset takes place as shown in gure 18.
The status window in which you will be able
to conrm that you are connected pops-up, as
shown in the red frame of gure 19.
Figure 17
Figure 18
Figure 19

www.lanpro.com
Wireless - Equipment - 123 Manual - LP-C290N
300 Mbps Wi-Fi Access Point (AP) - Conguration as a Client
8
Proceed to change the password of the LP-C290N,
we highly recommend this. This password will
let you access as an administrator, to perform
this, please select: Management/Language
(Time) and input it in the Password eld and
immediately select Apply, as shown in figure
20.
Figure 20
23
LanPro is continuously improving its products and reserves the right to change
specications and availability without prior notice.