Laserworld CS-400RGB User manual

CS-400RGB
USER MANUAL
Please read this manual carefully before use!

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
of
1
I
Table of contents
Page
1. SAFETY INSTRUCTIONS 3
. OPERATING DETERMINATIONS 4
3. PACKAGE LIST 4
4. PRODUCT INTRODUCTION 5
5. FUNCTION INTRODUCTION 5
6. INSTRUCTIONS 5
7. CHANNEL’S FUNCTION 6
8. SIGNAL CONNECTION AND ADRESS DIALING 7-10
9. SAFETY MARKS 10
10. MAINTENANCE 11
11. TECHNICAL SPECIFICATIONS 11
hecking Parts
Please check if the following parts are included:
1 x CS-400RGB Laser
1 x Power cable
1 x User manual

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
3
of
1
DANGER LASER RADIATION!
Avoid direct eye exposure!
Laser radiation can cause eye damage and/or skin damage
All protective measures for a safe operation of this laser must be applied.
1. SAFETY INSTRU TIONS
- If the device has been exposed to drastic temperature fluctuation, do not
switch it on immediately. The arising condensation water might damage your
device. Leave the device switched off until it has reached room temperature.
1. The laser must only be used for shows. The operation is only allowed if it is
controlled by a skilled and well-trained operator.
- Never leave this device running unattended and keep it away from children
and unauthorized persons.
. Keep away from heaters and other heating sources. In order to safeguard
sufficient ventilation, leave 50 cm of free space around the device.
3. Never direct the laser beam to people or animals.
4. CAUTION LASER DIODE: Never unscrew the housing!
There are no serviceable parts inside the device. Maintenance and service
operations shall only be carried out by authorized dealers.
5. Always disconnect from the mains when the device is not in use or before
cleaning it.
- HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
4
of
1
2. OPERATING DETERMINATIONS
6. The operator has to make sure that laser radiation – also reflected laser
radiation –higher than the highest allowed level is avoided by technical or
organisational measures.
7. Make sure that the used voltage is : AC 0V~ 40V, 50/60Hz
8. If the device is used in a flying installation, the mounting brackets and an
appropriate safety-rope must be fixed.
9. Laser effects are not designed for permanent operation. Consistent operation
breaks will ensure that the device will serve you for a long time without
defects.
10.In some countries, the operator must notify the accidence insurance and the
authority for industrial safety, before operating a laser. For more information,
contact the relevant authorities.
11.Please consider that unauthorized modifications on the device are forbidden
due to safety reasons!
1 .If this device will be operated in any way differently than described in this
manual, the product may suffer damages and the guarantee becomes void.
Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock, etc.
Thank you for using the lub series RGB („7 colors“) laser projector. For
the sake of safety and better Operation of this projector, please read this
manual carefully before use and operate the projector , lest incur any
personal injury or damage to the projector.
3. PA KAGE LIST
When you unpack the case, please take time to examine the items as follow:
projector 1
Power cord 1
Owner’s manual 1
projector sling 1

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
5
of
1
4. PRODU T INTRODU TION
Club Laser RGB laser performance System adopts the latest appearance design to
make it compact and light.
Club Laser RGB laser projector adopts the semiconductor laser source. Red laser
wavelength is 650nm, and green laser wavelength is 53 nm, and blue is 473nm.lt is'
seven colors .Laser generator is double-temperature -controlled power supply. The
laser light source has a long life span and highly stability, complying with the
international Standard.
There are 85pcs latest patterns in it and 5pcs animation effect performances (4pcs
patterns can be operated individually at one time), can be used for word
performance, animation performance, laser beam performance, with spatial,
projection and animation effects. The scientific laser beam route design and fast
laser vibratory mirror System will announce a new era of laser lighting performance.
Control mode.- It has 6 DMX-51 Signal control channels, multiple control modes :
DMX-51 signal control, music control, automatic , master/slave and ILDA Controller.
There are 85pcs patterns in it, with different laser performance at the same time 7
colors laser projector was applied for the place of public entertainment such äs disco,
night club, TV Station and theater etc.
5. FUN TION INTRODU TION
RGB laser projector has much function. Abundant laser effect patterns,
automatic-switch ILDA connector,DMX-51 double-frame patterns controlling
and preprogrammed four- frame pattern individually controlling effect ;and 18pcs
different color controlling> perfect master & slave synchronization effect, this is will
be more convenient for your edition and performance, with the latest laser
performance —rotation, turning, moving, gradual drawing, dotting & breakpoint etc.
This laser product has 6 channels DMX-51 Signal control, can perform many
different laser effects, such äs laser brightness adjustment ,laser strobe effect, time
tunnel effect,3D effect and so on. Meanwhile, it can be also controlled by the music,
and the sound active effect can be controlled by the rhythm.
6. INSTRU TIONS
After unpacking, check whether the laser lighting has been damaged by transport
such as any screw loosening, lighting tube broken, etc. If everything is OK, select a
proper location, hang the light and adjust its angle properly, then connect the power
cord and the ground wire before switch on at the means.
This product belongs to grade-1 protective equipment. Notice that while using this
laser lighting the green and yellow wire has to connect the ground properly by
Professionals. Please examine the electrics and voltage before power on it. We
suggest customer apply 110V 30V or a transformer. 0 seconds after powered on
the projector, it will self-check and then can be used.
Because of the radiate laser generator’s own characteristic and to secure the laser's
long life span. please terminate it for 10 minutes after using it for 30 minutes. Avoid

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
6
of
1
being interfered by other Signals while controlled by Fire Phoenix Software or using
the DMX-51 Signal Controller, such as wireless interphone & high radiated source.
7. HANNEL’S FUN TION
ChanneJ DMX-51 numerical
value 0~ 55
controlling
0~41 Laser light switch off
4 ~83 DMX-51 : Primary programmed laser
effects performance
84~1 5
DMX
-
51 : Double patterns A
controlling
1 6~167 DMX-51 : Double patterns B controlling
168~ 09 DMX-51 : Automatic control
CH1 Control
modes
selection
10~ 55 DMX-51 : Sound active control
Effects
mode
Select the primary programmed laser
effects
CH
Double
patterns
0~ 55
Patterns selection of double patterns A
or double patterns B
CHS Effects
mode
Dot horizontal movement
Double
patterns
0~ 55
Different controlling effect selection of
double patterns A or B.
Effects
mode 0~ 55 Dot vertical movement
0~1 7 Moving speed ac|justment of double
patterns AorB
CH4
Double
patterns
1 8~ 55 Double patterns changes into single
pattern; moving speed adjustment.
CHS
Color
control
0~ 55 18 colors effect control mode.
CH6 Color
speed
0~ 55 Adjust the colors changing speed from
fast to slow.

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
7
of
1
8. SIGNAL ONNE TION AND ADRESS DIALING
When the Controller transmits DMX51 Standard Signals, the connection of which is
accomplished through the "inpuf and "outpuf 3-pin XLR socket. When a console
Signal Outputs to the unit, it must correspond to the Pin 1 Ground, Pin Positive and
Pin 3 Negative of the XLR socket on the unit. If it does not work just try exchanging
the Pin and Pin 3 (these pins are generally do not need exchanged for consoles).
The Signal wire length should not exceed 100m in order to avoid the interference of
the other Signals by any other electric appliances.
If your DMX-51 signal Controller adopt 5 pins XLR plug, you need one transfer line-
from 5 pins to 3 pins the transfer method as following:
When control Signals from the console inputs into 7 colors laser performance
System. The projector must be assigned a data Start address code, so that a unit
may act on the corresponding coqtrol Signal. Thus, when any Controller is used,
every unit must have its own data Start address Accordingly, the address of the first
unit is set äs 1, the second unit has also channels based on the first code, so its
address code is 7,the third unit is set at 13,so on and so forth (the setting method
will also depend on the specific console, the above is just for general cases).

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
8
of
1
The details of DMX-512 Signal control mode address switch as follow:
Lamp
no:
Start
address
Control switch (ON)
1 1 1
7 1, , 3
3 13 1, 3, 4
4 19 1, , 5
5 5 1, 4, 5
6 31 1, , 3, 4, 5
7 37 1, 3, 6
8 43 1, , 4, 6
9 49 1, 5, 6
10 55 1, , 3, 5, 6
: : :
This 7 colors laser performance System has controlled by on/off switch address code.
1 to 9 are the numerical value DMX 51 Signal, 10 is the exchange switch of DMX51
Signal control and music control, automatic, master and slave.
Control mode set up detail as bellow:
MODE Control switch (ON)
1 DMX-51 10:ON
Single projector
controlled by sound
1:ON
3
Single projector
automatic control
mode
1— 10:OFF
4 master projector
synchronization
controlled by sound
1:ON
5 Master projector
synchronization
automatic control
1— 10:OFF
6 Slave projector
synchronization
control mode
:ON
Under sound active control mode: There is a sound sensitivity adjustment function,
so you can adjust it to the Optimum sound according to your requirement.

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
9
of
1
Scanning Operation of seven colors selection and color change (The address
code is under DMX-51 control)
Channel Value Function
1 4 -83
0-9
3 Horizontal scanning adjustment
4 Vertical scanning adjustment
0- 47 Seven colors selection 5
48- 55 Color change
6 Adjustment of color changing speed(fast to
slow)
Attention: The light will shutoff automatically when the dotting scanning function
keeps still for 15seconds.
When the value of both Channel 3 and Channel 4 is 0, the dotting will be in the
middle and lighting after 15 seconds' stagnation.
Operation of double-pattern control mode
(The address code is under DMX-51 control)
Channel Value Function
84-1 5 Pattern A control
1
1 6-1 7 Rattern B control
Pattern selection
3 Control mode selection
0-1 7
Double pattern moving speed adjustment (slow to
fast)
4
1 8- 55
Single pattern moving
speed adjustment(slow to fast),
double pattern to single pattern (pattern A or pattern
B)
5 Color control selection
6 Color changing speed adjustment (fast to slow )
Operation under ILDA connecter control mode:
Connected to ILDA Signal, the switch will automatically turn to ILDA connecter
control mode.
Attention: Power off before the connection of ILDA Signal to avoid the damage of
the projector.
Attention of Master/Slave ontrol Mode:
1 .You can not connect to the DMX-51 Controller when the master and slave
projector are operating synchronously, otherwise the master and slave synchronous
functions can't be realized;

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
10
of
1
.When operating the master and slave controlling, it must be only one master
projector, otherwise it can not be operated synchronously.
9. SAFETY MARKS
Before maintenances, please refer to eligible personnel.
Please make sure to switch off the power before Installation or maintenance.
Please do not use power and lasers that do not conform to the current
specifications.
Please do not see the laser light directly, in case it might damage the eyes.
Avoid electric shock! Bulb overheating;
Do not use any power voltage and light type of different specifications
Do not expose to the laser light outside.
Do not use it trequently under the humid atmosphere.
Keep the reflecting mirror clean and dry.

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
11
of
1
10. MAINTENAN E
Maintenance should be performed every 15-day period, by using a sponge which is
dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the
mirror.
Always disconnect from the mains when the device is not in use or before cleaning it.
There are no serviceable parts inside the device. Maintenance and service operations
are only to be carried out by authorized dealers.
Never look directly into the light source.
Always disconnect from the mains when the device is not in use or before
cleaning it.
11. TE HNI AL SPE IFI ATIONS
Power supply: AC 110V/AC 0V, 50/60 Hz
DMX 512: 10 channels
ondition temperature: -10°C ~ +35°C
Operating Environment: indoor
Signal input power: -5V~+5V
Power consumption: 150W
Working mode: DMX51 , Live Play @ Music (Sound Programme), ILDA
Optical power: ca. 400mW RGB (white)
Green: ca. 100mW / 53 nm; Red: ca. 50mW / 650nm;
Blue: ca. 75mW / 473nm
Laser classification: 3b
Weight: 0 kg
Dimensions: 560 x 410 x 30 mm (L x W x H)
PLEASE NOTE
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and
unskilled operation!

USER MANUAL: Laserworld Proline CS-400RGB
Date: 01/ 008
Page
1
of
1
EU- Declaration of onformity
We hereby confirm that the following device
Laserworld lub S-400RGB Laser Projector
complies with the essential safety requirements, laid down in the regulations of the
committee to assimilate the provisions of law of all participating EU states on the
electromagnetic compatibility (89/446/EWG).
The device has been classified considering the following EU-norms on
electromagnetic compatibility:
DIN EN 55103-1: 1996
DIN EN 55103- : 1996
DIN EN 61000-3- : 000 + A : 005
DIN EN 61000-3-3:1995 + A1: 001
Assessment of compliance of the product with the requirements relating to the Low Voltage
Directive (LVD) was based on the following standards:
DIN EN 60065 : 00
Furthermore, the device is verified in correspondence to the laser class
regulations DIN EN 608 5-1, if properly set up according to the upper
mentioned laser safety regulation.
After installing the device, an inspection and official approval is indispensable for the overall
setup. The inspection must follow the European guidelines EN 608 5-1 and corresponding
regulations for the prevention of accidents BGV-B . This declaration is executed on behalf of
the CS-400RGB Laser manufacturer
Laserworld (Switzerland) AG
c/o LOG.ON GmbH
Raiffeisenstrasse 8
78658 Zimmern ob Rottweil
GERMANY
VAT number: DE252331844
WEEE-Reg.-Nr.: DE 93014361
Laserworld (Switzerland) AG
based in:
Rheinblick Residenz
Oberstrasse 1
8274 Tägerwilen
SWITZERLAND
Authorized person:
Supervisory board Ms Rhea Gössel
place of business: 8274 Tägerwilen / Schweiz
company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
www.laserworld.com
[email protected]