LEGRAND 6338 53 User manual

Four Source, Eight Zone Distribution Module
6338 53
LE00367AA
SOURCES INTEGRATION
12
INTERCOM
I/R PORT
SINGLE
A MULTI B
ZONES
12 34
24VDC@2.5A
24VDC@2.5A
56 78
DISTRIBUTION MODULE#AU1002
Description
Installation
Figure 1
All components of a Multi-source Audio System are wired centrally from the Four Source, Eight Zone
Distribution Module.Inaddition to providing acentral point of connection, the Module distributes the
necessary voltage to power the system (one power supply per each four zone group).The Triple-source
and Single-source Inputs and Keypad Volume Controls connect directly to the module utilizing RJ-45
connections.The system can support expansion by “daisy chaining” Single Source, Four Zone Distribution
Modules, 6338 21,toany of the eight outputs.The IR RJ45 jack is used to both receive and transmit IR
signals and has its own LED for activity status.
NOTE: The two 24 Volt, 2.5 Amp Power Supplies, 6338 41, are not included and must be purchased
separately.
Installation of the Legrand Four Source, Eight Zone Distribution Module and related components, is best
accomplished at multiple times during new construction, at “First Fix” before the drywall is installed, and at
“Second Fix” after the drywall is installed and painted.
NOTE: The Four Source, Eight Zone Distribution Module provides power to all of the components
of the Audio System.
A "First Fix" Steps:
-Run three Category 5ecables from the room location containing the Source Inputs (typically the
entertainment centre location) to the Enclosure.
-Run Category 5ecables from the room locations which will contain the Keypad Volume Controls to
the Enclosure.

Entertainment Center
-CD player
-Tape Deck
-A/V Receiver
Dual IR Mouse
Emitters (6338 46)
SOURCE
SOURCE
Universal IR Target
(6338 47)
Four Source Eight
Zone Distribution
Module (AU1002)
Local Source
Input (6338 68*)
Universal IR
Remote Control
(6338 50)
Triple source
input (6338 48)
Amplified
Keypad Volume
Control with IR
(6338 64*)
In-Ceiling Speakers
(6338 43)
Audio In
L
R
IR Emitters
123
Emitter 3
56KIR Filter
On
IR
Status
IR Input
Single Source
input (6338 22)
Wallplate
Fourth Audio Device
Spare Cat 5e
Cable run
Wallplate
* Finished in Synergy Anthracite
Safety instructions
This product should be installed preferably by aqualified electrician.
Incorrect installation and use can entail risk of electric shock or fire.Before carrying out the installation,
read the instructions and take account of the product’s specific mounting location.Donot open up the
device.
All Legrand products must be exclusively opened and repaired by personnel trained and approved by
LEGRAND. Any unauthorised opening or repair completely cancels all liabilities and the rights to
replacement and guarantees.Only use genuine accessories.
Figure 2
B "Second Fix" Steps:
NOTE: Make sure that the Power Supply is not connected to the Distribution Module.
-Install the Four Source, Eight Zone Distribution Module in an enclosure using the included plate's tabs
and push pins.
-Terminate all Category 5ecables with RJ-45 plugs using the T568A wiring standard.
-Connect the Single Source Input and Triple Source Input AUDIO OUT jacks via aCategory 5ejumper,
to wall jacks with RJ-45 inserts.These jacks in turn should be wired to the SOURCE IN jacks of the
Four Source, Eight Zone Distribution Module (see Figure 2).
-Connect the Category 5 cables coming from the room locations containing the Keypad Volume
Controls to the Zone Output jacks on the Four Source, Eight Zone Distribution Module (see Figure 2).
-If applicable, expand the system by connecting one or more Single Source, Four Zone Distribution
Modules to the Zone Out jacks on the Four Source, Eight Zone Distribution Module.
-Plug one or two 24 Volt power supply cables into the Power jacks on the Distribution Module
(depending on Zone usage).
-Verify system functionality.
Optional components and Cat 5e wiring to control four audio devices