LEGRAND 0 677 23L User manual

Stickers
x2
Setup button
Do not remove
the cover plate
Wireless, batteryless
lighting control
Frequency bands: 2.4 - 2.4835 GHz
Power level: < 20 mW
Or
Module Control Gateway power outlet and home/
away wireless master switch
Pack contents:
Requires to install the connected starter pack and one or more «... with Netatmo» connected switch, micromodule
or socket outlet.
Wireless and batteryless lighting control
0 677 23L/73L/79L
0 770 53L - 6 000 83L
5 742 10/39/55 - 5 743 24
7 418 13L/43L/73L
LE12380AC-EN
Short push ON/OFF
Long push Dim +25%
(2 short pushs OFF)
Short push ON/OFF
Long push Dim -25%
(2 short pushs OFF)

2
Or
> 3 s
Make sure that the indicator lights on the wired products are green and not flashing. If not, go back to
precedent step. 1.
Start the configuration
Press the configuration button of Module Control or press the middle of the wireless master switch until its light
briefly turns green, and then stop pressing. All wired products lights will turn green.
1
2Pair the wireless, batteryless switch to control the connected products (switch, micromodule,
socket-outlet, latching relay).

3
Multiple pairing: You can control several switches with the same wireless, batteryless switch by repeating the
operation for each product that you want to control.
A1B
+
+
+
C
A1BC
A2BC
To complete your installation, briey press the congu-
ration of the Module Control or the middle of the wire-
less Home / Away master switch.
All the indicator lights on the products switch o
Complete the installation
3
< 1 s
Or
< 1 s
A1
B
C
A2
Tap 3 times the product to be controlled with the wireless, batteryless control. The light of the product to control flashes
rapidly.
For the specific case of the latching relay, press the main button of the latching relay until the configuration indicator
flashes slowly in blue, release it then tap the wired product you want to control 3 times with the wireless, batteryless
control. The indicator light of the product to be controlled flashes rapidly.
While holding the "setup" button on the wireless, batteryless control, briefly press the "ON" or "OFF" button on the
wireless batteryless control.
The indicator light of the product to control will briefly turn blue, and then will turn green again.The pairing was successful.
Check the correct pairing by pressing ON/OFF buttons
+
If necessary, erase the conguration of the wireless
batteryless control (factory reset)
While holding the "setup" button on the wireless,
batteryless control, press the upper button for 5 seconds.
Conrm that your control is correctly reset by making an
ON command, then OFF
5 s

4
H > 2 m
H < 2 m
Put the stickers in place Before fixing the wireless control(s) with
the removable stickers provided, test one
on a non-visible area of the wall.
LEGRAND - Pro and Consumer Service - BP 30076
87002 LIMOGES CEDEX FRANCE • www.legrand.com
www.legrandoc.com/067723L
Download the app
Your installation is ready. You can download the Legrand Home +
Control application to control your lights remotely.
Model: ZLGP17
T
he undersigned, Legrand declares that the radio-electric equipment type
(0 677 23L/73L/79L - 0 770 53L - 6 000 83L - 5 742 10/39/55 - 5 743 24 -
7 418 13L/43L/73L) complies with directive 2014/53/EU. The full text of the
EU declaration of conformity is available on the following website:
www.legrandoc.com
You can also fix the wireless control(s) permanently to
the wall with screws.
FCC ID: 2ACN8-ZLGP1X IC: 12132A-ZLGP1X Model : ZLGP17
This device contains licence-exempt transmitter(s)/receiver(s) that comply withFCC RF andInnovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the device.
This device complies with FCC and ISED radiation exposure limits set forth for general population. This device must not be co-located or
operating in conjunction with any other antenna or transmitter.
FCC Caution: the user that changes or modications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined by turning the equipment o and on, the user is encouraged to try to correct
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety instructions
Make sure the power supply is disconnected before any intervention.
Strictly comply with instructions for installation and use.