LEGRAND The Radiant Collection User manual

installation guide
Wi-Fi Smart Switch

2
table of contents
before you start..................................3
what you need ...................................4
installation and setup ................ 6–19
getting to know your switch ......20-21
specifications...................................22
faqs ..............................................23
regulatory information......... 24–27
warranty.......................................28
support ........................................29

3
before you start
Review this guide in its entirety before beginning device installation. Consult an
electrician with any questions or if you are unsure of your abilities.
DWarning: Incorrect installation could
result in death, serious injury, and/or
damage to your home or devices.
DCaution: To reduce the risk of injury
and/or overheating and damage to other
equipment:
• For dry, indoor use only.
• Do not use to power medical equipment.
• Not suitable as a disconnecting means.
• Do not use with loads exceeding the
device load rating (see page 22).
• Connect the smart switch to a
120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the
smart switch and follow all applicable
local and national electrical codes.
• Install in a non-metallic electrical box
to protect wireless signal strength.
Visit the Legrand website at www.legrand.us/radiant/smart-lighting/support for
installation videos or to learn more about your smart device.

4
what you need
REQUIRED:
Phillips-head screwdriver
Flat blade screwdriver
YOU MAY ALSO NEED:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring
leads (included), and wire nuts (included)

5

6
installation & setup
step one
|
turn off the power for your device at the
circuit breaker
Flip the existing light switch multiple times to confirm the power is off.
NOTE: If there are multiple devices next to your existing light switch, make sure
power is off at the circuit breaker for all of those devices.

7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON

8
installation & setup
step two
|
remove the existing device
Check for the following wires:
1HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the
purposes of this guide. Do not touch or let “hot” wires contact other wires.
2LOAD: Directs power to your light(s).
3NEUTRAL: Creates a path to return current to the power source when the
device is off. Required for your switch installation.
4GROUND: Provides a safe path for electricity in the event of a short circuit.
5TRAVELER: If more than one switch controls the light, an additional wire will be in
the box that “travels” to the other switch.
NOTE: Refer to the “faqs” on page 23 if you are unsure of your wiring.

9
OFF
ON
OFF
ON
OFF
ON
VOLTAGE
TESTER
Load
Supply
“Hot”

10
installation & setup
step three
|
wire the smart switch
Use the wire nuts provided to secure the wires together.
1Connect the WHITE neutral wire on the switch to the neutral wires in the box, using
the red wire nut.
2Connect the LOAD wire on the switch to the load wire in the box.
3Connect the HOT wire on the switch to the hot wire(s) in the box.
4Connect the GREEN ground wire on the switch to the ground wire(s) in the box.
5If the light is controlled with only one switch, use a wire nut to cap the YELLOW
traveler wire on the device. If more than one switch controls the light, connect the
YELLOW traveler wire on the device to the wire going to the other switch.
NOTE: This product will work with existing three-way switches. The switch can be installed
in either location.

11
1-POLE
Ground
WHITE
3-WAY
HOT
OFF
ON
OFF
ON
OFF
ON
Load
Supply
“Hot”

12
installation & setup
step four
|
secure the smart switch
1Gently fold the wires into the electrical box. Be careful not to pinch a wire or
loosen anywire nuts.
2Use the device screws to secure the smart switch to the electrical box. Do not
fully tighten the screws.

13

14
installation & setup
step five
|
test the smart switch
NOTE: See page 20 for feature details.
1Turn the power back on at the circuit breaker.
2Press the paddle switch to turn your light on and off.
TROUBLESHOOTING TIP:
If the device is not powering, reference the “faqs” on page 23 to determine if
you have reversed the “hot” and “load” wiring.

15
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON

16
installation & setup
step six
|
attach the screwless wall plate
1Noting which side faces out, align the sub-plate over the device screws. Use
the sub-plate screws (provided) to secure the sub-plate to the smart switch.
2Tighten the device screws to secure the smart switch to the electrical box.
3Angle the end of the screwless wall plate over the top edge of the
sub-plate. Push the screwless wall plate down and in until it “snaps” into
place over the sub-plate.
NOTE: To remove the wall plate, place the tip of a flat blade screwdriver into the slot
under the wall plate and twist gently.

17
THIS SIDE OUT
MOUNT OVER DEVICE
THIS SIDE OUT
MOUNT OVER DEVICE
THIS SIDE OUT
MOUNT OVER DEVICE
1 32

18

19
installation & setup
step seven
|
set up your system
1Download and launch the Smart Lights app by Legrand. The app is available
on the App Store or on Google Play.
2Connect your smart switch to your home network by following the step by step
instructions in the app.
3Use the app to control your smart switch.
Google Play and the Google Play logo are trademarks of Google LLC. App Store is a service mark of Apple Inc., registered in the U.S. and other countries.

20
getting to know your switch
Item Name Description
1 Paddle Switch
• Press the top of the paddle to turn the light on
and the bottom to turn the light off.
2 LED Locator Light Indicates the current state of the device. Refer to
“LED Locator Light Explanations” for detail.
•To return the switch to factory default, with the
load off, press and hold the “off” button for 10s.