Leviton Decora NE505 User manual

For Technical Assistance Call:
1-800-824-3005 (U.S.A. Only)
www.leviton.com
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not
for the benefit of anyone else that this product at the time of
its sale by Leviton is free of defects in materials and
workmanship under normal and proper use for five years from
the purchase date.Leviton’s only obligation is to correct such
defects by repair or replacement, at its option, if within such
five year period the product is returned prepaid, with proof of
purchase date, and a description of the problem to Leviton
Manufacturing Co., Inc., Att: Quality Assurance
Department, 59-25 Little Neck Parkway, Little Neck, New
York 11362-2591. This warranty excludes and there is
disclaimed liability for labor for removal of this product or
reinstallation. This warranty is void if this product is installed
improperly or in an improper environment, overloaded,
misused, opened, abused, or altered in any manner, or is
not used under normal operating conditions or not in
accordance with any labels or instructions. There are no
other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but
if any implied warranty is required by the applicable
jurisdiction, the duration of any such implied warranty,
including merchantability and fitness for a particular purpose,
is limited to five years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including
without limitation, damage to, or loss of use of, any
equipment, lost sales or profits or delay or failure to
perform this warranty obligation. The remedies provided
herein are the exclusive remedies under this warranty,
whether based on contract, tort or otherwise.
DI-000-NE505-00B
Scene Controller w/IR
Receiver (Multi-Location)
Cat. No. NE505
24VDC
24mA, 0.6W
For use w/compatible Leviton LCnet products
For more information go to
www.leviton.com/D3200
INSTALLATION INSTRUCTIONS
DI-000-NE505-00B
Frame
Strap
Snaps
Push in 2 Locations
OFF
IR Receiver
A
A
A
A
Figure 1 - Scene Controller Functions
Figure 2 - Color Conversion
FEATURES
•Leviton’s Decora®Style design • IR Receiver is compatible with a standard remote control
•Each NE505 can recall 4 consecutive (1-4, 5-8,...29-32) scenes • Color conversion available
for up to 256 configurations, with additional equipment • Fits standard wall box
•Low-Voltage for easy installation
•Gangable with 7 additional units for selection of up to 32 scenes
INTRODUCTION
The Scene Controller w/IR Receiver, Cat No. NE505, allows-easy-to use manual control of a Scene Capable LCnet Lighting Control System. The Controller is a
Decora-style device that sends commands for 4 distinct scenes, or an OFF command, to LCnet compatible scene dimmers. The device provides a unique, entry pad
interface with an infrared receiver for use with any standard remote control, including a compatible Leviton Remote. The NE505 is ideal for secondary entrance ways
within a D3200 System.
DESCRIPTION
The Controller has a user-friendly five-button face. The NE505 incorporates a program mode that configures the Scene Controller to 4 selectable and consecutive
scene numbers ( i.e., Scene 1 through 4 or Scene 5 through 8).The NE505 has the capability to call up to 32 scenes when used with a D3206/8 device and can call
as many as that unit can hold. Once programmed, pressing a scene button adjusts the lights to that scene with the active configuration. The Controller also features
an OFF button and an IR Receiver which allows commands to be executed using a Leviton IR Remote, Cat. No. NE210, or any standard IR Remote Control.
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2)
This device must accept any interference received, including interference that may cause undesired operation.
INSTALLATION INSTRUCTIONS
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
WARNING: IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN.
CAUTION: DISCONNECT POWER WHEN SERVICING FIXTURE OR CHANGING LAMPS.
CAUTION: THE SCENE CONTROLLER WITH IR OPERATES OFF OF LOW-VOLTAGE (24VDC), SO CARE MUST BE TAKEN WHEN REPLACING A LIGHT
SWITCH. CONSULT LOCAL BUILDING CODES AND REGULATIONS FOR PROPER LOW-VOLTAGE INSTALLATION.
TO INSTALL:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
2. Connect per appropriate WIRING DIAGRAM as follows: Insert each lead into appropriate Plug connector location by pushing firmly (refer to Wiring Diagrams 1
and 2). If using stranded wire, twist strands of each lead tightly (making sure that there are no stray strands) and push firmly into appropriate Plug connector
location.
NOTES:
•LCnet must be wired using a twisted pair for the CAN_H and CAN_L wires. Leviton recommends using CAT5 wire.
•If the device is the first or last one on the bus, the LCnet must be terminated. Use the terminating plug (included) making sure to connect shorting wire to CAN_H
or you may also short the center terminal in the connector on the device to the CAN_H terminal (refer Wiring Diagrams 1 and 2).
3. Tighten the screws on the Plug connector making sure that no bare conductor shows. Connect Plug connector to Jack on the back of the Controller.
4. Carefully position all wires to provide room in outlet box for Controller. Mount Controller into box with mounting screws supplied.
5. Replace wallplate as follows:
•Remove "A" tab when using standard Decora® wallplate (refer to Figure 1).
•Leave “A” tabs intact when using Decora® Screwless wallplate.
6. Restore power at circuit breaker or fuse. INSTALLATION IS COMPLETE.
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your interior design requirements. Simply obtain a color conversion kit of the appropriate color from your Leviton
distributor and proceed as follows (please note that wallplate must be removed).
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using a small screwdriver, gently remove the frame from the strap (refer to Figure 2).

GND (Green) GND
Not Used Not Used
+24V DC (Green/White) +24V DC
CAN-L (Blue/White) CAN-L
CAN-H (Blue) CAN-H
LCnet
Back of Scene Controller
GND (Green)
GND
Not Used
Not Used
+24V DC (Green/White)
+24V DC
CAN-L (Blue/White)
CAN-L
CAN-H (Blue)
CAN-H
GND (Green) GND
Not Used Not Used
+24V DC (Green/White) +24V DC
CAN-L (Blue/White) CAN-L
CAN-H (Blue) CAN-H
LCnet
Back of Scene Controller Back of Scene Controller
Wiring Diagram 2 - Two Location Application
Wiring Diagram 1 - Single Station Application
DI-000-NE505-00B
M
AX
OF
F
S
CEN
E
S
5
1
2
34
67
8
M
AX
OF
F
S
CEN
E
S
5
1
2
34
67
8
NE210 Remote
NE210 Remote
3. Take the new frame and position it properly to the strap. Orient the frame so that the OFF button is the bottom button. Line up the plastic
snaps with the square holes in the strap. Insert the snaps on one side of the frame into the strap.
4. Firmly press sideways and down to slip the other snaps into place. The frame snaps in with an audible click. Ensure that all four snaps
are secure. Replace Decora®wallplate. The color conversion is complete.
TO OPERATE
Scenes 1-4, 5-8,...Scene 29-32 (refer to Step 3 of Scene Programming section):
SCENE BUTTON: Press the Scene button. The lights will fade ON to the preset light level.
OFF: Press the OFF button. The lights will fade OFF.
NOTE: Each button will illuminate when pressed except when the Controller is in the Program Mode.
SCENE PROGRAMMING
1. Press and hold button 1 and 3 on the Controller for approximately 5-7 seconds. All the LED’s will blink to indicate that the Controller is in
Program Mode.
NOTE: Pressing any button while the LED’s are flashing in the Program Mode, will exit the mode without any programming stored.
2. Call Scene from Cat. No. D3206/8 (refer to D3206/8 User Guide) or other source.
3. Once the Scene is called, the LED’s will stop flashing and the device will exit Program Mode. The buttons are now programmed based
on the Scene called as follows:
If Scenes 1-4 are called on a LCnet Scene Capable Dimmer, button 1 on the Controller is programmed for Scene 1; button 2 is Scene 2;
button 3 is Scene 3; button 4 is Scene 4.
If Scenes 5-8 are called on a LCnet Scene Capable Dimmer, button 1 on the Controller is programmed for Scene 5; button 2 is Scene 6;
button 3 is Scene 7; button 4 is Scene 8 and so on.
4. The OFF button will always be programmed as OFF.
NOTE: If there is partitioning in the application, repeat the above procedure for each configuration used.
IR PROGRAMMING
The NE505 has a Learning IR capability that allows users to select any button (command from IR Remote) to correspond with desired
scene programmed and OFF.
1. Press and hold the desired Scene or OFF button on the Controller for approximately 5-7 seconds until it’s LED begins flashing. The
Controller is now in the Infrared Remote Control Program Mode.
2. Press the desired button on the IR remote to correspond with the desired Controller button.
NOTE: If Remote generates only one control signal when the button is pressed and the Controller LED continues to flash, you must
press the button on the IR Remote again until the flashing stops.
3. The Controller Scene button is now programmed to respond to the IR command.
4. Repeat the above procedure for each button used, including OFF.
NOTE: If in different configurations the button on the IR Remote calls a different Scene number, you must repeat the programming
procedure.
TROUBLESHOOTING
•If NO LED’s are lit; there is no power
- Check wiring.
•Communication LED does NOT light when the button is pressed
- Check power wiring connections.
For Multiple Power Packs on the Bus:
•The Controller has power (at least the OFF LED is ON) but pressing the buttons have no effect on the lights; there is no communication
between the Controller and the Power Pack
- If the communication LED does NOT flash when a button is pressed, see above.
- If the communication LED does flash, check the address of the Power Pack and Controller (refer to Dimming Power Pack
Instructions).
Terminating Plug
CAN-H
Middle Terminal
LCnet Termination
Terminating Plug
CAN-H
Middle Terminal
LCnet Termination

Front Panel
FOLD SCHEME
8.5¨
14.0¨
Fold Line
Front Panel
12345
#'s = Fold Sequence
Front Panel
Cat. No.
Cat. No.
DOCUMENTATION
DOCUMENTATION
LEVITON INSTRUCTION SHEET/MANUAL
LEVITON INSTRUCTION SHEET/MANUAL
SPECIFICATIONS
SPECIFICATIONS
kkc 06/01/05
Helvetica
DI-000-NE505-00B
Black
N/A
Final fold size:
Final fold size:
50 Lb. offset
2.8" X 4.25"
Overall size:
Overall size:
14" X 8.5"
Paper size:
Paper size: