Life Fitness Elevation 95X-ALLXX-01 User manual

Elevation 95X-ALLXX-01 Commercial Cross-trainer
HOW TO…

Elevation 95X-ALLXX-01 Commercial Cross-traine
r
“How To…”
29
Console Back Cover
Phillips Screws (6)
to console
HOW TO... REPLACE THE CONSOLE BACK COVER
Tools required: Phillips screwdriver
Estimated time required: 15 minutes
1. If the cross-trainer has line cords, unplug
them from the wall outlets.
2. Remove and save the six Phillips screws
that secure the console back cover to the
console support bracket and console.
3. Install the new console back cover using
the screws removed and saved in Step 3.

Elevation 95X-ALLXX-01 Commercial Cross-trainer
“How To…”
30
Phillips
Screws (4)
Console Support Bracket
Console
HOW TO... REPLACE THE CONSOLE
Tools required: Phillips screwdriver
Estimated time required: 30 minutes
1. If the cross-trainer has line cords, unplug
them from the wall outlets.
2. Disconnect all cables from the console.
3. Remove and save the four Phillips screws
that secure the console to the console back
cover.
4. Install new console in reverse order using
hardware removed and saved in step 4.
5. Test the console for proper operation.

Elevation 95X-ALLXX-01 Commercial Cross-traine
r
“How To…”
31
Media Tray
HOW TO... REPLACE THE MEDIA TRAY
Tools required: none
Estimated time required: 15 minutes
1. If the cross-trainer has line cords, unplug
them from the wall outlets.
2. Press the tab on the inside of the media
tray to release it and then pull it up and out
of the top deadshaft cover.
3. Push new media tray down until it snaps
into place.

Elevation 95X-ALLXX-01 Commercial Cross-trainer
“How To…”
32
Phillips Screws (2)
Front Dead Shaft
End Cap Cover
Rear Dead Shaft
End Cap Cover
HOW TO... REPLACE THE DEADSHAFT END CAP COVERS
Tools required: Phillips screwdriver
Estimated time required: 20 minutes
1. If the cross-trainer has line
cords, unplug them from the
wall outlets.
2. Remove and save the two
Phillips screws that secure
the deadshaft end cap covers
to each other.
3. Install the new deadshaft end
cap covers using hardware
removed and saved in step 3.

Elevation 95X-ALLXX-01 Commercial Cross-traine
r
“How To…”
33
Console Console (raised)
Console Support Bracke
t
Top Dead
Shaft Cover
Phillips
Screws (2)
Phillips
Screws (3)
HOW TO... REPLACE THE TOP DEADSHAFT COVER
Tools required: Phillips screwdriver
Estimated time required: 30 minutes
1. If the cross-trainer has line cords, unplug them
from the wall outlets.
2. Remove the console back cover. (See the “How
To…” on page 29).
3. Remove and save the media tray.
4. Remove the right and left deadshaft end cap
covers. (See the “How To… on page 32.)
5. Raise the console slightly to allow access to the
two upper mounting screws that secure the top
deadshaft cover to the unit.
6. Remove the five screws that secure the top deadshaft cover to the unit.
7. Install the new top deadshaft cover in reverse order using hardware removed and saved
in steps 4, 7, and 8.
Be careful not to allow the console to fall while raising it.

Elevation 95X-ALLXX-01 Commercial Cross-trainer
“How To…”
34
Console Support Assembly
Washers (2 on
each side)
Hex Bolts (2
on each side)
HOW TO... REPLACE THE CONSOLE SUPPORT ASSEMBLY
Tools required: Phillips screwdriver, 13mm socket wrench
Estimated time required: 45 minutes
1. nplug the line cord from the wall outlet.
2. Remove the console back cover. (See the
“How To…” on page 29.)
3. Remove the console. (See the “How To…”
on page 30.)
4. Remove the media tray. (See the “How
To…” on page 31.)
5. Remove the deadshaft end cap covers.
(See the “How To…” on page 32.)
6. Remove the top deadshaft cover. (See
the “How To…” on page 33.)
7. Remove and save the four bolts and
washers that secure the console support
bracket to the monocolumn.
8. Re-route the cabling through the new
console support bracket.
9. Reverse steps 3 through 7 to complete
the re-assembly.

Elevation 95X-ALLXX-01 Commercial Cross-traine
r
“How To…”
35
Heart Rate Hand
Senor (front)
Heart Rate Hand
Senor (rear)
Phillips
Screws (3)
HOW TO... REPLACE THE USER ARM HEART RATE HAND SENSORS
Tools required: Phillips screwdriver
Estimated time required: 20 minutes
1. If the cross-trainer has
line cords, unplug them
from the wall outlets.
2. Remove the three screws
that secure the inner
and outer hand sensors
to each other.
3. Note the location of the
wires on the hand
sensors. This will
simplify reassembly.
4. Disconnect the wires.
5. Connect the wires to the
new hand sensors.
6. Install the new hand
sensors using the screws
removed and saved in
Step 3.
7. Test the new hand
sensors for proper
operation.

Elevation 95X-ALLXX-01 Commercial Cross-trainer
“How To…”
36
Phillips Screws (to
front collar dead
shaft cover, 4)
Phillips Screws (to
monocolumn, 2)
Rear Collar
Dead Shaft Cover
Phillips Screws (to
rear collar dead
shaft cover, 2)
Front Collar
Dead Shaft
Cover
HOW TO... REPLACE THE FRONT OR REAR COLLAR DEADSHAFT COVERS
Tools required: Phillips screwdriver
Estimated time required: 20 minutes
1. If the cross-trainer has line cords,
unplug them from the wall outlets.
2. Remove the deadshaft end cap
covers. (See the “How To…” on page
32.)
3. Remove and save the two Phillips
screws that secure the front collar
deadshaft cover to the monocolumn.
4. Remove and save the four Phillips
screws that secure the front collar
deadshaft cover to the rear collar
deadshaft cover.
5. Install either the new front collar
deadshaft cover or rear collar
deadshaft cover using the screws
removed and saved in steps 4 and 5.