Life Gear 26800 User manual

DYNASTY
MAGNETIC RECUMBENT BIKE
ITEM NO: 26800
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2014, Oct.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE LIST ----------------------------------------------------------------------- 6
TOOLS -------------------------------------------------------------------------------------- 6
OVERVIEW DRAWING -----------------------------------------------------------------7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
OPERATING THE COMPUTER ------------------------------------------------------ 18
ADJUSTMENTS -------------------------------------------------------------------------- 20
MAINTENANCE -------------------------------------------------------------------------- 21
TROUBLESHOOTING ------------------------------------------------------------------ 21
WARM UPAND COOL DOWN ROUTINE ----------------------------------------- 22

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 120 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Hexagon Socket Pan Head Cap
Bolt M8x45 2 024 Screw ST4.8x20 2
002 Big Curve Washer Ø8xØ20x2.0T 7 025R Right Decorative Cover 1
003 Rear Handlebar Foam Grip
Ø30xØ24x595 2 025L Left Decorative Cover 1
004 Hand Pulse Sensor with Wire
(L=750 mm) 2 026 Cross Recessed Pan Head Tapping Screw ST4.8x20 3
005 Wire Grommet Ø12.1 2 027 Computer (ST-3604) 1
006 Rear Handlebar Ø25x1.5t 1 028 Extension Sensor Wire
(L=650 mm) 1
007 Cross Recessed Pan Head
Tapping Screw ST4.2x20 2 029 Extension Hand Pulse Sensor Wire II (L=650 mm) 2
008 Washer Ø8xØ16x1.5T 20 030 Tablet and Water Bottle Holder
Frame 1
009 Cap Nut M8 (S13) 6 031 Tension Control Knob 1
010 Handlebar End Cap Ø25 4 032 Tension Cable L=750 mm 1
011 Cross Recessed Pan Head Bolt
M6x15 8 033 Cross Recessed Pan Head Bolt M5x10 4
012 Big Washer Ø6xØ18x1.5T 8 034 Big Washer Ø5xØ19x1.0T 1
013 Backrest and Seat Support
Bracket End Cap 23x53x2.0t 1 035 Cross Recessed Pan Head Bolt M5x20 1
014 Back Cushion 1 036 Hexagon Socket Pan Head Cap
Bolt M8x10 4
015 Seat Cushion 1 037 Hexagon Socket Flat Head Cap
Bolt M8x15 1
016 Back and Seat Support Bracket 1 038 Front Post Cover 1
017 Hexagon Socket Pan Head Cap
Bolt M8x15 16 039 Hexagon Socket Pan Head Cap Bolt M8x20 1
018 Bushing 2 040 Big Washer Ø8xØ20x2.0T 1
019 Seat Sliding Tube 23x53x2tx493 1 041 Hexagon Nylon Nut M8 (S14) 1
020 Rear Main Frame 1 042 Idler Arm 1
021 Triangle Knob M12 1 043 Spring Ø18xØ3.0x56 1
022 Extension Hand Pulse Sensor
Wire (L=1000 mm) 1 044 Bearing 6000-2Z 2
023 Round Knob M16x1.5 1 045 Washer Ø10xØ14x1.0t 2

5
PARTS LIST
No. Description Qty No. Description Qty
046 Washer Ø6xØ12x1.0t 1 067 Belt Pulley with Crank Ø260 1
047 Cross Recessed Pan Head Bolt
M6x10 1 068 Washer Ø24xØ40x3.0t 1
048 Hexagon Nut M6 (S10) 2 069 Bearing Nut I 15/16” 1
049 Spring Washer Ø6 2 070 Ball Bearing 2
050 Tension Bracket 31x30x1.0t 2 071 Bearing Cup Ø56x2.25x68 2
051 Eyebolt M6x36 2 072 Extension Hand Pulse Sensor Wire
I (L=1400 mm) 1
052 Nut M10x1.0xH6 (S14) 2 073 Cross Recessed Pan Head
Tapping Screw ST2.9x12 2
053 Flywheel Ø250 1 074 Sensor with Wire (L=750 mm) 1
054 Belt (PJ390J6) 1 075 Rubber Cover Ø13 2
055R Rear Right Stabilizer End Cap 1 076 Front Main Frame 1
055L Rear Left Stabilizer End Cap 1 077 Bearing Nut II 7/8” 1
056 Rear Stabilizer 55x50x1.5tx580 1 078 Washer Ø23xØ34.5x2.5t 1
057 Carriage Bolt M8x65 4 079 Hexagon Nut 7/8” 1
058 Hexagon Nut M10 (S17) 3 080R Front Right Stabilizer End Cap 1
059 Adjustable Leveler M10 3 080L Front Left Stabilizer End Cap 1
060 Cover Cap Ø60xØ26x6.5 2 081 Front Stabilizer 55x50x1.5tx580 1
061 Cross Recessed Pan Head
Tapping Screw ST4.2x25 8 082 Hexagon Nylon Nut M6 (S10) 2
062 Screw ST4.2x20 6 083 Transport Wheel Ø45x19 2
063R Right Cover 1 084 Cross Recessed Pan Head Bolt
M6x35 2
063L Left Cover 1 085 Tablet and Water Bottle Holder 1
064 Crank Disk Ø391x21 2 086 Curve Washer Ø8xØ16x1.5T 2
065 Cross Recessed Pan Head
Tapping Screw ST4.2x10 16 087 Front Post (70x30x1.5t) 1
066R Right Foot Pedal (YH-30X) 1 088 Plastic Screw Anchor Ø8x32 1
066L Left Foot Pedal (YH-30X) 1 089 Front Handlebar Foam Grip
Ø30xØ24x160 2

6
HARDWARE LIST
TOOLS
(2) Big Curve Washer
Ø8xØ20x2.0T
6 PCS
Allen Wrench S6
1 PC Multi Hex Tool with Phillips Screwdriver S10, S13, S14, S15
1 PC
(1) Hexagon Socket Pan
Head Cap Bolt M8x45
2 PCS
(9) Cap Nut M8 (S13)
6 PCS (57) Carriage Bolt M8x65 4 PCS
(8) Washer Ø8xØ16x1.5T
2 PCS

7
68 69 70 71
71 70 77 78 79
66R
67
75
76
7473
54
48 49 50 51 52
52
53
61 63R62
61
62
6160
61
61
61
61
61
64
65
58
59
74 38
237
8
36
34 35
31
32
17
86
30
28 29
8
33
27
17
8 17
1
2
89
6
4
10
539
44
42
45 45 44 46 47
40 41
43
9
2
55R 56
55L
9
2
5
13
11
12
4
4
11
12
14
15
8
7
16
17
36
8
18 19
20
18
21
23
22
24
25R
24
26
25L
22
60 62
63L
65
64
66L
72
72 32
58
59 57
75
80R
81
80L
57 62
82
84
84
82
83
83
85
87
88
3
3817
10
89
89 10
51
OVERVIEW DRAWING

8
ASSEMBLY INSTRUCTIONS
1. Front Stabilizer Installation
Position the Front Stabilizer (81) in front of the Front Main Frame (76) and align bolt holes.
Attach the Front Stabilizer (81 onto the front curve of the Front Main Frame (76) with two
Ø8xØ20x2.0T Big Curve Washers (2), two M8 Cap Nuts (9), and two M8x65 Carriage Bolts
(57). Tighten cap nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
Tool:
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
76
9
2
57
81
(2) Big Curve Washer
Ø8xØ20x2.0T
4 PCS
(9) Cap Nut M8 (S13)
4 PCS (57) Carriage Bolt M8x65 4 PCS

9
2. Rear Stabilizer Installation
Position the Rear Stabilizer (56) behind the Rear Main Frame (20) and align bolt holes.
Attach the Rear Stabilizer (56) onto the rear curve of the Rear Main Frame (20) with two
Ø8xØ20x2.0T Big Curve Washers (2), two M8 Cap Nuts (9), and two M8x65 Carriage Bolts
(57). Tighten cap nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
9
2
57
56
20
Tool:
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
(2) Big Curve Washer
Ø8xØ20x2.0T
4 PCS
(9) Cap Nut M8 (S13)
4 PCS (57) Carriage Bolt M8x65 4 PCS