Lifepro PAWRUNNER User manual

PAWRUNNER PET TREADMILL
READY,
SET, PRO
USER MANUAL

Regular exercise
has enormous
benefits for your
pet’s body, brain,
and mental health.
Many pets,
especially dogs,
need daily exercise
for optimal health.
HELLO THERE.
Joel and I are athletes who suffered from
severe ACL injuries a few months apart.
We purchased multiple pieces of exercise
equipment for our in-home rehab but were left
disappointed and frustrated by fitness gear
that made big promises but gave no support, no
well-thought-out plan to follow, and no results.
And that’s how Lifepro came about, and why
the Endurance Training collection was created
— we’ve set out to change all of that. It’s why
every piece of equipment bearing our name
not only undergoes rigorous scrutiny to make
sure it delivers on power and efficacy, but also
comes with built-in support from our ‘guiding
angels’ and a built-in lifetime warranty so that
you’re never left hanging.
Welcome to Lifepro.
We’re in this together now.

With the Lifepro PawRunner Pet Treadmill, you can help your pet improve
cardiovascular fitness, build muscle strength, and lose weight—all from the
comfort of home. The PawRunner’s ultra-quiet motor is designed specifically
for in-home use.
The PawRunner is perfect for anyone who finds it difficult to take their
pet for regular walks due to very hot or cold weather, rain or snow, busy
streets, lack of parks or sidewalks, or a busy work or family schedule. The
PawRunner is also ideal for pets that require high levels of exercise and
mental stimulation.
It is estimated that half of dogs and cats are overweight or obese. If
your pet is experiencing mobility issues, joint pain, high blood pressure, or
diabetes due to being overweight, combine a nutritious, portion-controlled
diet with regular walks on the PawRunner treadmill to help them reach a
healthy weight.
The PawRunner treadmill has a speed-range of 0.5–7.5 mph. Twelve preset
exercise programs provide your pet with endless workout challenges. Three
countdown modes allow you to set specific workout goals such as distance
walked, workout duration, or calories burned. With the Lifepro PawRunner,
your pet can walk or run to improved strength, stamina, and cardiovascular
health. See results in as little as 15–20 minutes a day.
Redefine your workouts and experience the
transformative power of the Lifepro PawRunner:
Increase strength & stamina: improves stability and muscle tone
Regulate weight: boosts your heart rate and burn calories.
Decrease chronic pain: improves core strength & circulation
Boost your metabolism: encourages your body to burn fat faster
Decrease your stress: increases serotonin and decreases cortisol
Lower blood pressure: improves circulation
Develop stronger bones: increases bone density
Check out the information in this manual for ways to get started using your
PawRunner. Next, be sure to visit our website pawrunner.lifeprofitness.com
for access to our FREE library of workout videoswhich demonstrate how to
easily incorporate the PawRunner into your pet’s fitness routine.
Endurance Training Collection 5

6PawRunner User Manual Lifepro Endurance Training Collection 7
GET ACQUAINTED
Lifepro PawRunner
Pet Treadmill
Baseframe (A) Two Baseframe
End Caps (B)
Crossbar (C)
Ten Velcro®
Strips (D)
Six Curved
Washers (M)
Magnetic
Safety Key (O)
Bottle of
Maintenance Oil (P)
T-Knob (J) T-Knob Post (K) Six M6×6mm
Screws (L)
Console &
Adjustment Post (I)
Remote
Control (Q)
Hex Key (N)
Left (G) & Right (H)
Side Panels
Left (E) & Right (F)
Sidebars
GET STARTED
WHAT’S IN THE BOX
A. Treadmill Baseframe
B. Baseframe End Caps (2)
C. Crossbar
D. Velcro®Strips (10)
E. Left Sidebar
F. Right Sidebar
G. Left Fabric Side Panel
H. Right Fabric Side Panel
I. Console and Adjustment Post
CUSTOMER SUPPORT
If you have any questions about assembling and using your PawRunner
treadmill, we’re here to help. Call or email us and an experienced
customer support representative will be happy to assist you:
support@lifeprofitness.com or [phone].
PAWRUNNER
PET TREADMILL
ENDURANCE TRAINING
FIRST STEP
1. Remove all packaging from the treadmill baseframe, parts, and hardware.
Have someone to assist you with lifting the treadmill baseframe from the
packaging, it is heavy and bulky.
2. Confirm that all parts and hardware listed above are included.
3. Read carefully through this user manual, especially USING THE MAGNETIC
SAFETY KEY on page 9 , GETTING YOUR PET READY on page 20, PET
EXERCISE SAFETY on pages 23–25, and SAFETY INSTRUCTIONS on
pages 44–46 before assembling and using the treadmill.
4. Go to pawrunner.lifeprofitness.com and register your product within
14 days of purchase to activate your lifetime warranty.
5. Complete the steps in the 10MINUTE ASSEMBLY GUIDE on page 11 to
assemble your PawRunner.
6. Then, see GETTING YOUR PET READY, EXERCISE RECOMMENDATIONS,
and OPERATING INSTRUCTIONS to get started using the PawRunner.
J. T-Knob
K. T-Knob Post
L. M6×6mm Socket Head Screws (6)
M. Curved Washers (6)
N. Hex Key
O. Magnetic Safety Key
P. Bottle of Maintenance Oil
Q. Remote Control
R. User Manual

8PawRunner User Manual Lifepro
PARTS OF THEPAWRUNNER
Endurance Training Collection 9
USING THE MAGNETIC SAFETY KEY
THE MAGNETIC SAFETY KEY
The safety key MUST be in place before the treadmill can be used.
The error code “Err” or “E00” will show on the console until the magnetic
safety key is in place on the magnetic port on the treadmill console. If
the safety key is removed from its port during use, the treadmill will stop
automatically and cannot be restarted until the safety key is back in position.
This safety feature causes the treadmill to stop immediately in the event
your pet trips, falls, or another emergency occurs.
WHAT TO DO IN AN EMERGENCY
WARNING: You must clip the magnetic safety key to your pet’s collar
every time the treadmill is used.
• Stop the treadmill immediately if you realize that your pet cannot keep up
with the pace, or if any other emergency arises.
• Pulling the cord will remove the magnetic safety key from its port; this
will cause the treadmill to stop immediately.
• Make sure that all third parties are familiar with all safety instructions in
this manual and that they always use the magnetic safety key correctly.
DISABLING THE PAWRUNNER FOR SAFETY
To prevent the treadmill from being used by unauthorized third parties,
always remove the safety key when you have finished using the treadmill.
Keep the safety key stored in a separate place, out of the reach of
unauthorized people, especially children.
FRONT
REAR
Non-Skid Feet (2)
Running Belt
Plastic End
Caps (2)
Fabric Side
Panels (2)
Motor
Housing
Wheels (2)
Crossbar T-Knob
(adjusts console
height and angle
from side-to-side)
Console Tilt Knob
(adjusts console
angle up-and-back)
Console
Adjustment
Post
Sidebars (2)
Power Switch
& Integrated
Power Cord
Console
Velcro®Tabs
(5 per side panel)

INSTALL THE BASEFRAME END CAPS
You will need: treadmill baseframe (A), 2 end caps (B),
hex key (N)
Endurance Training Collection 11
SAFE PLACEMENT OF YOUR PAWRUNNER TREADMILL
• Use the treadmill in a well-ventilated room and avoid using in rooms that
are too warm to prevent heat exhaustion and heat stroke.
• Set up the treadmill with at least 7 feet of clearance from walls and
furniture at the back and at least 4 feet of clearance at the front and
sides of the treadmill. Never place the treadmill with the back of the
running belt against a wall, door, stairs, or any other obstruction.
• Do not use outdoors or in high-moisture, high-temperature, or high-dust
environments.
• Only operate and store the PawRunner on a flat, non-slip floor.
• Ensure the running deck is level to the ground. If the deck is positioned on
an uneven surface, it could cause damage to the electrical system.
• If setting up in a carpeted room, check underneath the treadmill to ensure
clearance between the carpet and the running deck. If there is not enough
clearance, or you’re not sure, place a mat or rug under the PawRunner.
Ensure the mat or rug is at least 55” × 30” and will not slip during use.
• Sometimes after an extended amount of use, you will find a fine black
dust under the treadmill. This is normal wear and does not mean there is
anything wrong with the treadmill. The dust can be easily vacuumed up. If
you wish to prevent the dust from getting on your flooring or carpet, place
a mat or rug under the treadmill.
SAFE PLACEMENT OF THE TREADMILL 10-MINUTE ASSEMBLY GUIDE
10 PawRunner User Manual Lifepro
1. Lay the treadmill baseframe (A) on a flat, non-slip floor.
2. Locate the four screws on the outside-rear of the treadmill baseframe.
There are two screws above each of the two non-skid feet.
3. Use the hex key (N) to remove the two screws on the left side of the
baseframe.
4. Align one plastic end cap (B) with the two screw holes.
5. Re-insert the two screws to secure the end cap.
6. Repeat 2–5 above to install the second end cap to the right side of the
baseframe.
7. Use the hex key (N) to fully tighten the screws.
A
B
B
TOOLS & HARDWARE
(N)
1

12 PawRunner User Manual Lifepro Endurance Training Collection 13
ATTACH THE CROSSBAR TO THE BASEFRAME
You will need: crossbar (C), 2 M6×6 screws (L),
2 curved washers (M), hex key (N)
ATTACH VELCRO®STRIPS TO THE CROSSBAR
You will need: crossbar (C), 2 Velcro®strips (D)
1. Insert the base of the crossbar (C) onto the two round inserts on either
side of the treadmill baseframe (A), just behind the motor housing.
2. Place a curved washer (M) onto one of the screws (L).
3. Insert the screw/washer combination through the screw holes on the
left side of the crossbar (C) and into the baseframe (A).
4. Repeat 3–4 above to attach the right side of the crossbar to the
baseframe.
5. Use the hex key (N) to fully tighten each screw.
1. Loop one Velcro®strip (D) around the left side of the crossbar (C) and
one strip around the right side:
• The smooth side of the Velcro®strip will face to the INSIDE of
the treadmill. The hook and loop side of the Velcro®will face to the
OUTSIDE of the treadmill.
• Loop just enough of the Velcro®strip around the crossbar to be
able to close the loop. The rest of the strip will extend straight out
creating a Velcro®tab. This tab will be used to attach the fabric side
panels.
• Position the two loops a few inches from the base of the crossbar.
• The loops should be loose enough that they can be repositioned
along the crossbar, if necessary.
C
C
D
A
D
(L)
(M)
x2
x2
TOOLS & HARDWARE
(N)
L
M
32

14 PawRunner User Manual Lifepro Endurance Training Collection 15
ATTACH VELCRO®STRIPS TO THE SIDEBARS
You will need: 8 Velcro®strips (D), left sidebar (E),
right sidebar (F)
NOTE: The two sidebars are identical until the Velcro®strips are applied,
then one will be the left sidebar (E) and the other will be the right
sidebar (F).
1. Set one sidebar on the ground on the left side of the treadmill.
2. Loop four Velcro®strips (D) along the sidebar:
• The smooth side of the Velcro®strip will face to the INSIDE (RIGHT)
of the treadmill. The hook and loop side of the Velcro®strip will face
to the OUTSIDE (LEFT) of the treadmill.
• Loop just enough of the Velcro®strip around the crossbar to be able
to close the loop. The rest will extend straight out creating a Velcro®
tab. This tab will be used to attach the fabric side panels.
• Position three loops along the long side of the sidebar and one loop
on the short side of the sidebar.
• The loops should be loose enough that they can be repositioned
along the side panel, if necessary.
3. Lay the left sidebar (E) on the ground until the next step.
4. Set the second sidebar along the right side of the treadmill.
5. Loop four Velcro®strips (D) along the sidebar in the same manner:
• The smooth side of the Velcro®
strip will face to the INSIDE
(LEFT) of the treadmill. The
hook and loop side of the
Velcro®strip will face to the
OUTSIDE (RIGHT) of the
treadmill.
6. Lay the right sidebar (F) on the
ground until the next step.
4INSTALL THE SIDEBARS TO THE BASEFRAME
You will need: left sidebar (E), right sidebar (F),
4 M6x6 screws (L), 4 curved washers (M), hex key (N)
5
1. Insert the left sidebar (E) (the Velcro®tabs face OUTSIDE/LEFT) onto
the rounded inserts on the left side of the crossbar and on the top of
the baseframe.
2. Put a curved washer (M) onto one of the screws (L).
3. Insert the screw/washer combination through the screw holes in the
left sidebar (E) and crossbar (C). Don’t tighten the screw yet.
4. Place another washer onto another screw.
5. Insert the screw/washer combination through the screw holes in the
sidebar (E) and baseframe (A). Don’t tighten the screw yet.
6. Repeat 1–5 above to attach the right sidebar (F) to the right side of the
crossbar (C) and baseframe (A).
7. Use the hex key (N) to fully tighten all four screws.
A
(L)
(M)
x4
x4
TOOLS & HARDWARE
(N)
L
M
F
B
E
L
M

16 PawRunner User Manual Lifepro Endurance Training Collection 17
ATTACH THE FABRIC SIDE PANELS TO THE SIDEBARS
You will need: left fabric side panel (G), right fabric side panel (H)
6
A
G
E
F
H
INSTALL THE T-KNOB AND T-KNOB POST
You will need: T-knob (J), T-knob post (K), hex key (N)
7
1. Screw the T-knob (J) clockwise into the threaded insert in the side of
the T-knob post (K). Do not fully tighten the knob yet.
2. Locate the metal tube running along the right side of the treadmill
baseframe (A).
3. Locate the two socket-head screws inserted into the metal tube
towards the front of the treadmill.
4. Use the hex key (N) to remove the two screws.
5. Align the T-knob post (K) with the two screw holes. The lip on the
T-knob post goes UP.
6. Re-insert the two socket-head screws to secure the T-knob post.
7. Use the hex key (N) to fully tighten the screws.
K
J
TOOLS & HARDWARE
(N)
1. Identify the left fabric side panel (G): the Velcro®tabs on the backside
of the fabric side panels face to the INSIDE. The tabs on the backside
of the left panel face RIGHT; the tabs on the backside of the right
panel face LEFT. See figure below.
2. Stick the bottom strip of Velcro®on the back of the left fabric side
panel (G) to the corresponding Velcro®strip along the left side of the
baseframe (A).
3. Stick the five Velcro®tabs on the back of the left side panel (G) to the
corresponding tabs on the left sidebar (E) and crossbar (C). Reposition
the tabs along the sidebar and crossbar, if necessary to line up the
Velcro®.
4. Repeat steps 2–3 to attach the right fabric side panel (H) in the same
manner.

18 PawRunner User Manual Lifepro Endurance Training Collection 19
INSTALL THE CONSOLE
You will need: console and adjustment post (I)
8
LUBRICATE THE RUNNING BELT
Before using your PawRunner treadmill for the first time, you must
lubricate the running belt with the included bottle of maintenance
oil (P). Follow the steps in LUBRICATING THE RUNNING BELT on
page 38.
9
1. Ensure the console cable exists the bottom of the adjustment post (I).
Pull the end of the cable out of the bottom of the post, if necessary.
2. Insert the adjustment post (I) into the T-knob post (K).
3. Turn the T-knob (J) clockwise to tighten it and secure the console and
adjustment post to the treadmill.
4. Pull the console cable through the bottom of the T-knob post.
5. Connect the console cable with the corresponding cable exiting the
right side of the treadmill.
I
J
K
I
J
CUSTOMIZING THE TREADMILL
ADJUSTING THE CONSOLE HEIGHT AND VIEWING ANGLE
The console may be raised or lowered and rotated from side to side for
easy viewing.
1. Loosen the T-knob by turning it counterclockwise.
2. Slide the console up or down to the desired height.
3. Rotate the adjustment post from side to side until the console is facing
the desired direction.
4. Tighten the T-knob by turning it clockwise to secure the console in place.
The console may be tilted up and back via the tilt adjustment knob. There are
two tilt options.
1. Loosen the tilt adjustment knob by turning it counterclockwise.
2. Tilt the console up or back to the desired angle.
3. Tighten the tilt adjustment knob by turning it clockwise.
ADJUSTING THE INCLINE OF THE TREADMILL
The treadmill deck can be tilted to three different incline levels: 4.5°, 5.1°,
and 5.7°. The treadmill arrives at the lowest level. To adjust the tilt:
1. Twist the two incline adjustment knobs counterclockwise to loosen them.
2. Hold the base of the treadmill with one hand. With your other hand, pull
the head of the knob out as you pull the incline adjustment post down.
You will hear a click with the incline adjustment knob clicks into the
next incline level. Repeat with the second knob.
3. Adjust until the incline is at your desired angle.
123