Lippert Promaster User manual

Promaster Sliding Door
OEM INSTALLATION MANUAL

Rev: 05.23.22 Page 2 CCD-0006239
TABLE OF CONTENTS
Introduction 2
Safety 2
Required Resources 3
Pre-Installation 3
Installation 4
Introduction
This document outlines the procedure to install the Promaster Sliding Door for Class B RVs.
NOTE: Images used in this document are for reference only when assembling, installing and/or operating
this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Additional information about this product can be obtained from lci1.com/support or by downloading the
free LippertNOW app. The app is available on Apple App Store® for iPhone® and iPad® and also on Google
Play™ for Android™ users. Apple App Store®, iPhone®, and iPad® are registered trademarks of Apple Inc.
Google Play™ and Android™ are trademarks of Google Inc.
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause
death or serious personal injury if not performed safely and within the parameters set forth in this
manual.
Failure to follow instructions provided in this manual may result in death, serious personal injury
and/or severe product and property damage, including voiding of the component warranty.
Always wear eye protection when performing service, maintenance or installation procedures.
Other safety equipment to consider would be hearing protection, gloves and possibly a full face
shield, depending on the nature of the task.
The “CAUTION” symbol above is a sign that a safety risk is involved and may cause personal injury
and/or product or property damage if not safely adhered to and within the parameters set forth
in this manual.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage,
including voiding of the LCI limited warranty.

Rev: 05.23.22 Page 3 CCD-0006239
Required Resources
• Standard screw gun
• Phillips screw driver
• #8 x 1 screw
Pre-Installation
Remove Promaster Sliding Door assembly from box and place parts flat on a surface for easy assembly (Fig. 1).
Filler Panel
Side Support
Lower Sliding Channel
Upper Sliding Channel
End Cap
Screws
Fig. 1
The rope mechanism is attached to the lower and upper sliding channels. Make sure the rope
mechanism does not tangle with the sliding channels.
1X 2X
3 x 30
3X
3 x 20
2X
3 x 20 3.9 x 13

Rev: 05.23.22 Page 4 CCD-0006239
Installation
1. Place the end of the lower sliding channel into the bottom of the side support (Fig. 2) and align the
guide to feed the rope into the top channel.
Rope
Rope
2. Slide the lower sliding channel all the way through, leaving a little bit of rope loose at the end. Place
the end cap on the end of the lower sliding channel (Fig. 3).
Fig. 2
End Cap
Fig. 3
3. Loop the extra rope at the end around the end cap to the upper channel and slide with fingers up the
rope to the side support. Make sure that the rope is taut (Fig. 4).
Rope
Fig. 4
Lower sliding channel

Rev: 05.23.22 Page 5 CCD-0006239
4. Slide the lower slide channel back to the screw holes (Fig. 5).
Stop
Fig. 5
5. Take the upper sliding channel (Fig. 6) and attach it to the top of the side support (Fig. 6).
Fig. 6
Upper Slide Channel
6. With standard screw gun place the screw in the upper part of the side support that is attached to the
upper slide channel and tighten (Fig. 7).
Fig. 7
1X
3 x 30
Align holes

Rev: 05.23.22 Page 6 CCD-0006239
7. Remove any packing tape that is attached to the assembly.
8. Insert the fill panel into the side support notch and work from the bottom up until it is secure (Fig. 8).
NOTE: Be sure that the arch of the fill panel is at the bottom of the sliding door (Fig. 9).
Side support notch
Fig. 8
Fill panel
Once the door is completely assembled, it is ready to lift and place in the door opening of the van.
9. Lift the frame assembly.
10. Rest the bottom of the frame on the bottom entry of the van (Fig. 9).
11. Guide the fill panel between the door seal and the mounting back, assuring that it is at a 90 degree
angle (Fig. 10).
Lower Sliding Channel
Fig. 9
Fig. 10
Fill Panel
Door Seal
Mounting Back

Rev: 05.23.22 Page 7 CCD-0006239
12. Guide the right side end of the upper sliding channel inside the van behind the door seal (Fig. 11).
Fig. 11
Door Seal
Upper Sliding Channel
13. Once in place, take a standard screw gun and secure the three 3 X 20 screws into the lower sliding
channel (Fig. 12).
Lower Sliding Channel
Screw Holes
Fig. 12
14. Slide the fill support back and align the screw holes with the holes in the lower sliding channel.
15. Secure side support by screwing the two 3 x 20 screws in tight (Fig. 13).
Fig. 13
3X
3 x 20
2X
3 x 20

Rev: 05.23.22 Page 8 CCD-0006239
16. Step inside the van and slowly close the screen door.
17. Screw the left side of the upper sliding channel with the two 3.9 x 13 screws to the mounting back with
the screw gun (Fig. 14).
Fig. 14
Screws
Upper Slide Channel
Mounting Back
18. Carefully open the screen door and step outside the van.
19. Using an OEM-supplied #8 x 1" screw, insert into the top of the fill panel to secure it to the mounting
back (Fig. 15).
Fill Panel Screw
Fig. 15
Mounting Back
2X
3.9 x 13

Rev: 05.23.22 Page 9 CCD-0006239
20. Slowly remove the string from the fringe on the van screen door (Fig. 16).
Fig. 16
String
21. Test the door by opening and closing the door (Fig. 17).
Fig. 17

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (LCI).
LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an
authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.
The information contained in this manual is subject to change without notice and at the sole discretion of LCI.
Revised editions are available for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Ph: 432-LIPPERT (432-547-7378) | Web: lippert.com | Email: [email protected]