LOCKLY GUARD DEADBOLT 728F ZU User manual

USER MANUAL
MANUEL D'UTILISATION
For commercial use & professional installation
www.LocklyPRO.com
DEADBOLT 728F ZU
DEADBOLT 728 ZU
Z-WAVE SMART LOCK
PGD728F ZU | PGD728 ZU

Table of Contents
TABLE OF CONTENTS
2.1 Product Overview - Exterior
2.2 Product Overview - Interior
2.3 Understanding Your New Lock
2.4 Reset Button
2.5 Keypad Display Switch
2.6 Rebooting Your Lock
2.7 Low Battery
2.8 Changing The Battery
Section 1 - Product Highlights
Section 2 - Product Overview
Section 3 - Using Your Smart Lock
3.1 Configuring Access
3.2 Entering Programming Mode
3.3 Adding an Access Code
3.4 Deleting an Access Code
3.5 Checking an Access Code
3.6 Z-Wave Settings
3.7 Adding a Fingerprint*
3.8 Fingerprint Scanning Directions*
3.9 Fingerprint Scanning Tips & Troubleshoot*
3.10 Deleting Stored Fingerprints*
3.11 Adding Secure Link
Section 4 - Locking and Unlocking
1.1 Product Features
4.2 Unlocking with Fingerprints*
4.3 Locking / Unlocking with LocklyPro App
4.4 Locking / Unlocking with Physical Key
4.5 Safe Mode
4.6 Rain Mode
4.7 Shine Mode
4.8 Welcome Mode
Section 5 - Advanced Features
5.1 Offline Access CodeTM (OAC)
Section 6 - Important Notes
6.1 Important Notes
Section 7 - Cleaning
7.1 Cleaning
Section 8 - Safety Precautions
8.1 Safety Precautions
For additional support, visit http://LocklyPro.com/support
or email [email protected]
1
2
3
4
5
5
6
7
8
9
10
11
13
15
17
16
20
21
22
23
24
25
26
27
28
30
31
31
32
33
34
35
4.1 Unlocking with Access Codes
*only available on 728F ZU

Patented Hack-Proof PIN Genie Keypad
Digits are randomly displayed on the keypad ensuring access codes to be undetectable to
intruders after repeated use. Numbers are randomly distributed across 4 buttons, with 3
numbers in each button. Users can press any button showing their number. Location of the
numbers are always different every time someone uses the keypad, making it hard for prying
eyes to guess the correct code.
Built in Z-Wave®module
Integrate with your Z-Wave smart home system, supports 2GIG GC2E and IQpanel QS9207
Z-Wave controller to lock and unlock from anywhere.
Multiple Access Codes & Monitoring
Store up to 33 Access Codes for family, friends and guests, as well as monitor entry and exit
records.
Advanced 3D Fingerprint Recognition
Biometric Fingerprint Recognition protocol allows up to 99 registered fingerprints to be
used and accepts only actual fingerprints - preventing lifted prints from being used. ( only
on PGD728F ZU )
Live Monitoring and Voice Control
Through your smartphone, monitor door access from anywhere in the world and securely
control who comes and goes with the Secure Link Wi-Fi Hub. (Requires Secure Link Wi-Fi
hub, sold separately PGH230)
Complete Privacy
The exterior displayed keypad can be locked and switched off using the simple ON/OFF
toggle from the inside panel. The owner can prevent others trying to input the passcode
from the outside and entering the home.
Offline Access Code™ (OAC)
The Offline Access Code™ can allow owners to issue access codes, set the allowed access
duration, all without Lock ever connecting to the internet, so in case of power outage, you
can still magically and remotely issue Access Codes without any connection to the web.
Backup Keys and 9V Battery Socket
The door can be opened with physical backup keys. There is also a 9V battery connection
socket for emergency power backup to access the keypad in case your smart lock runs out
of battery.
1.1 Product Features
SECTION 1.1 1
ENG

2.1 Product Overview - Exterior
SECTION 2.12
ENG
Reboot
Welcome/Safe Mode
Indicator
Battery Indicator
OK Button
Key Hole Cover
9V Battery Socket
Key Hole
Fingerprint Sensor

2.2 Product Overview - Interior
SECTION 2.2 3
ENG
Battery Compartment
(Operated by 4 x AA Batteries)
Battery Cover
Display Keypad Switch
Thumbturn
Beep Alert
Program Button
Reset Button

2.3 Understanding Your New Lock
SECTION 2.3
After the installation of your new Lockly Guard, understanding some key functions of operating
your smart lock is important. The following guides will walk you through resetting a lock,
adding Access Codes, deleting Access Codes, adding and deleting fingerprints, and how
to configure your OAC (Offline Access Code™).
For any questions you can always visit http://LocklyPro.com/support for assistance.
Don’t forget that Lockly Guard works best with our iOS and Android app. Please download
the app by visiting the link below.
4
Scan or visit LocklyPro.com/app
ENG
Lockly Guard supports working in both Z-Wave mode and LocklyPro App mode. Z-Wave
controller takes precedence over Lockly App. If you set the clock and time zone or
auto-locking through Z-Wave, the door lock will prioritize the Z-Wave controller settings.

2.4 Reset Button
SECTION 2.4 ~ 2.5 5
2.5 Keypad Display Switch
The exterior keypad screen can be locked
and turned off by using the ON/OFF switch
at the back panel (interior) of the smart
lock. When it is switched off, people who
are outside cannot enter any access codes
to unlock the door.
OFF ON
If you need to reset, you must have your Activation Code. The Activation Code can be found on the
Activation Code Card that came with the smart lock. Once the smart lock has been reset, all the
data previously stored will be deleted, after which you need to reset Z-Wave. See below which Reset
procedure applies for you.
ENG
Never Connected to Lockly App
Press Reset Button for 3 seconds, and the smart lock will restart and reset.
Connected to Lockly App
In the Settings menu of the App, select Perform
Factory Reset. The smart lock will restart and reset.
After reset, you'll need the Activation Code to
reconnect to the App.
If you replace a new smartphone
device, log in your existing Lockly
Guard account on the smartphone
and reconnect to the smart lock
according to the APP prompts.
Reset Button

2.6 Rebooting Your Lock
SECTION 2.6
Reboot Lockly Guard in case of dead battery or malfunction. No settings
will be changed and all Access Codes will still be stored within Lockly
Guard.
Press and release the reboot button when you want to reboot the lock. Your Lockly Guard
will beep once after reboot. Only reboot when necessary.
To reboot, find the reboot button located on the bottom of the exterior side of Lockly
Guard. The reboot button is located in the middle of the two 9V battery backup sockets.
You will need something small such as a paperclip, to press the reboot button. Insert the
paperclip and press down firmly and let go. Your screen should restart and the lock should
reboot automatically.
Reboot Button
6
ENG

ENG
2.7 Low Battery
SECTION 2.7
When the battery is in seriously low condition, Lockly Guard will make continuous beeping
sounds in addition to the flashing low battery icon on the touch screen. You should replace
batteries immediately to avoid your smart lock from shutting down.
When your smart lock low-battery warning alert finally dies, you will have 3 chances to
unlock your smart lock either by a password, APP or fingerprint. If the unlock was successful,
the low-battery warning alert will be on for 1 minute. After which, the smart lock will go to
dead-battery mode and will lock auto lock in 5 seconds and the screen will display a
low-battery icon.
Dead Battery
Condition Indicator Solution
Low Battery
Battery Icon on the display keypad
will light up to indicate low battery .
At the same time, Lockly logo on
the interior panel will flash red to
reminder users that battery is low.
Replace batteries immediately
to avoid battery failure. Lockly
Guard can still operate up to 300
cycles in low battery condition.
When there is no display and
sounds; and screen is non-functional.
Replace batteries immediately.
Supplied physical backup keys
can be used to unlock the door.
Alternatively, use a 9V battery
as shown below to temporarily
activate the lock.
Your Lockly Guard will automatically detect
battery polarity. So hold your 9V battery lead
in place against bottom of the Lockly Guard to
temporarily activate the screen to enter your
Access Code. Be sure to hold the 9V battery
against the contact points located at the
bottom of the lock until you have successfully
unlocked your door with your Access Code.
Once unlocked, batteries should be replaced
immediately.
7
-
+
9V Alkaline Battery

ENG
2.8 Changing The Battery
SECTION 2.8
Under normal use, the Lockly Guard battery will last up to a year. Please check battery levels
regularly and change your batteries when the low battery notification is issued. For best
practice, always use new batteries by a major brand.
Open the battery compartment cover and insert four (4) new AA alkaline batteries as
shown. Be sure to unscrew the screw located on the top of the cover first by unscrewing
counterclockwise before sliding the cover up.
- Make sure the batteries are oriented correctly by matching the orientation displayed.
- Replacing the batteries do not reset stored Access Codes.
- To see a list of recommended brands, please visit http://LocklyPro.com/support.
8
Whenever batteries are replaced, reconnecting the smart lock to your
smartphone app is required. If you have not yet downloaded the app,
visit: LocklyPro.com/app
+
+
-
+
-
-
+
-
Screw
RESET
PROGRAM

ENG
3.1 Configuring Access
SECTION 3.1 9
There are a total of five (5) buttons on the keypad as shown
in the example image to the left. The numbers in each button
may differ than what is shown on your device than what is
displayed here.
To enter your required digit, just simply press the circle where
your number is shown. You do not need to press the actual
number as anywhere within the circle will suffice.
The button on the bottom is the OK button. You will be pressing
this button when you are done entering your Access Code.
OK Button
Your new Lockly Guard Access Code can be any combination of 6 to 8 digits. Once a new
Access Code is entered, the Default Access Code of 123456 would be deleted. A maximum
of 33 sets of Access Codes can be stored for use at any given time. To add more than 33
sets of Access Codes, you must delete an existing Access Code before adding a new code.
There are different types of Access Codes that can be generated using the Lockly App.
Each type of access code have different levels of permission you can select for your
guests, tenants, deliveries, helpers, etc., Get the latest updates on access codes, visit:
www.support.lockly.com/faq/accesscodes/
The Default Access Code is 1 2 3 4 5 6

ENG
3.2 Entering Programming Mode
SECTION 3.2
Add / Delete Access Code or Fingerprint
ModeNumber
Z-Wave program settings
To enter Programming Mode, remove
the battery compartment cover on the
interior side of the Secure to expose the
Reset and Program buttons (See page 8).
Simply press the Program button to enter
programming mode.
Note: Program button will be disabled
once synced to a smart phone. Configure
all settings via synced smart phone. Access
Codes previously added by Programming
mode will be cleared.
To end Programming Mode, press the Program button anytime. Programming Mode will
automatically exit if the keypad is inactive for more than two hundred and forty (240) seconds.
After entering Programming Mode, you should see
the screen as displayed to the right on your Lockly
Guard keypad. PG menu is used to Add or Delete
Access Code or Fingerprint. If you have already
paired with LocklyPro App, this menu will no longer
be displayed. You can only add or delete Access
Code or Fingerprint through the LocklyPro App.
For Z-Wave program settings, Please see the Z-Wave
Module User Manual included in your package.
10
Program Button

ENG
3.3 Adding an Access Code
SECTION 3.3
While in Programming Mode, select “1PG” to add an Access Code. If you are not in
Programming Mode, please see Section 3.2 to enter Programming Mode.
After pressing “1PG” press “1AD” and select "Pd" to add an Access Code.
Enter your new 6 - 8 digit Access Code and press when
you are finished. You will then re-enter the code to confirm
your new Access Code.
Remember, just touch the digit you need within the circle
around each 3 numbers. There is no need to touch the exact
location of the number. For example, based on the example
image to the left, if you need “1”, you can touch the upper
left button. For “6”, you would touch the upper right button.
11

ENG
3.3 Adding an Access Code (Continued)
SECTION 3.3
If you have successfully entered your new Access Code
twice, you will see the new code displayed here. In this
example, we chose 654321. Press to Confirm or
to cancel.
To exit or cancel, you can always press or
If the two (2) Access Codes you entered does not match,
an error message will appear on the screen (As shown to
the left). Press OK Button to return to the Programming
Screen and try again.
OK Button
12

ENG
3.4 Deleting an Access Code
SECTION 3.4
OK Button
Active Access Codes will then be displayed on the screen in
sequence from left to right, top to bottom. In the example
shown on the left, the Access Code displayed is 1 3 5 7 9 0 .
Rotate through different Access Codes shown by touching
any number on the screen. If you find the Access Code you
want to delete, simply hold the OK Button for 3 seconds.
(Continue on next page)
13
While in Programming Mode, select “1PG” to delete an Access Code. If you are not in
Programming Mode, please see Section 3.2 to enter Programming Mode.
After pressing “1PG” press “2DE” and select "Pd" to delete an Access Code.

ENG
3.4 Deleting an Access Code (Continued)
SECTION 3.4
Once you have selected the Access Code you want to
delete, Lockly Guard will ask you to confirm deletion by
showing you the Access Code you are deleting, in this
example, 1 3 5 7 9 0.
Press to delete, or to cancel.
NOTE There are two incidents where your Access Code cannot be deleted.
Only one Active Access CodeNo Access Codes Set
There are no Access Codes set.
The factory default Access Code
cannot be deleted.
There is only one (1) Access Code saved in
the smart lock. At least one code must be
registered. Please add another Access Code
before attempting to delete the existing code.
14

ENG
3.5 Checking the Access Code
SECTION 3.5
While in Programming Mode, select "1PG" then select "3CH" to check registered
Access Codes. If you are not in Programming Mode, please see Section 3.2 to enter
Programming Mode.
Active Access Codes will then be displayed on the screen in sequence from left to
right, top to bottom. In the example shown on the left, the Access Code displayed is 1
3 5 7 9 0 .
Rotate through the different Access Codes by touching
any number on the screen.
To exit Check Access Code screen, simply press the OK
Button.
If there are no Access Codes registered in your smart
lock, Check Access Code mode will be invalid. The
default Access Code will not be shown on the display
keypad, and you will see the following screen shown to
the left instead.
15
OK Button

ENG
SECTION 3.616
3.6 Z-Wave Settings
In the programming mode, select "2HB" to enter the Z-Wave settings. Refer to the Z-Wave
Module User Manual for detailed instructions.

ENG
3.7 Adding a Fingerprint*
In this section, you will learn how to register a fingerprint to your new smart lock.
We are using an advanced biometric sensor, providing the most secure fingerprint
authentication. For security reasons, Lockly Guard will only accept fingerprint patterns
that consist of cross intersection points. Patterns with no cross intersection points will not be
acceptable.
Please check your fingers before registration to make sure the finger you want to register will
be acceptable by our system. Otherwise, use an alternative finger to ensure successful
registration.
The following examples show which types of fingerprint patterns will be acceptable. It is
highly recommended to enroll at least one finger from each hand in case the hand you
are using is unavailable, such as, in instances like if you are holding items in that hand or
have sustained an injury.
Your smart lock can register up to ninety-nine (99) fingerprints. Please read the following sections
if you want to add or delete fingerprints. We recommend using your app to add fingerprints,
however, the following section can show you how to add and remove fingerprints if you did not
pair your lock with a smart phone.
Fingerprint Pattern with Cross
Intersection Lines
Concentric or Parallel Pattern
with no Cross Intersection Lines
Fingerprint with Scars or
Worn Out Ridges
OK Not OK Not OK
SECTION 3.7 17
*only available on 728F ZU

ENG
SECTION 3.7
18
While in Programming Mode*, select “1PG” to add a Fingerprint. If you are not in Programming
Mode, please see Section 3.2 to enter Programming Mode.
After pressing “1PG” press “1AD” and select "FP" to register a Fingerprint.
Upon pressing “FP”, you will enter Fingerprint Registration Mode and you will see a green
LED ring light up on the fingerprint panel on the exterior side of Lockly Guard Deadbolt.
3.7 Adding a Fingerprint*(Continued)
Once you’re in Fingerprint Registration Mode you will see two
numbers displayed on keypad. The top number is your
Fingerprint Registration number, in this example to the left, “1”.
The bottom number will always start with a “6”.
You must successfully scan your fingerprint six (6) times for it to
properly register. Every time you scan your fingerprint, the
number on the bottom will change, starting from 6 - then 5, 4,
3, 2, 1, until the fingerprint is successfully registered.
Note: For reference, please keep a record of your fingerprint
registration number to distinguish whom it was registered to.
*Only works when lock is not paired with a smart phone device.
*only available on 728F ZU