LUCCI Air METT User manual

Installation Instructions
1 | P a g e v 1 . 0 ( 1 1 / 2 0 1 9 )
METT INLINE EXHAUST FAN
SKU# 209040
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all
instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.
Warranty
•This exhaust fan is covered by a 12 month warranty. The warranty is from date of purchase, not the date of
installation.
•If this exhaust fan is not assembled and installed by a licensed electrician the warranty will be void.
•Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquires.
•Warranty will be void if there is any damage due to improper usage or modification to the fan.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Safety Precautions
Read the Safety Precautions below before use and caring out installation.
•Always ensure the power is OFF and the fan has cooled down before performing any maintenance, cleaning or
making any adjustment to the fan.
•Means of all-pole disconnection must be incorporated in the fixed wiring.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the appliance.
•WARNING: If unusual oscillating movement is observed, immediately stop using the product and contact the
manufacturer, its service agent or suitably qualified persons.
•Do not allow any foreign object to enter the grille opening as which may damage the product.
•Ensure that the fan does not come in contact with corrosive chemicals solvents or abrasive cleaners etc.
•Clean the grilles regularly. To clean, wipe with a damp clean cloth. Do NOT soak or immerse the product in
water or other liquids.
Installation Requirements
•A licensed electrician is required to install this unit to the mains supply.
•All wiring and installation of the exhaust fan must adhere to the local council regulation and latest local and national
wiring rules, eg. AS/NZS 3000 electrical installations. If unsure, contact a licensed electrician.
•This exhaust fan must be installed to an isolation switch in accordance with the current AS/NZS 3000, also known
as wiring rules.
•This product is suitable for indoor use only. It is rated IPX2 which is protected against vertically falling water drops
when the enclosure tilted up to 15°.
•This exhaust fan is a Class II product and must be maintained during wiring and installation.
•The mounting point must be able to support at least 2 times of the weight of the product.
•Ensure all the clearance value to the structural building element are maintained according to the clearance diagram
in Fig.4.
•Do not install the inlet of the exhaust fan in canopies over stoves etc., as excessive heat will damage the product.
•This product is designed for installation on a flat ceiling only. Do not mount it on a sloping ceiling or a vertical wall.
•Any duct attached to the product must be installed horizontally in the ceiling and with the same height or lower than
the exhaust fan.

Installation Instructions
2 | P a g e v 1 . 0 ( 1 1 / 2 0 1 9 )
•Ensure the duct is not bent otherwise the performance will be reduced.
•Where applicable, precautions must be taken to avoid the back-flow of gases into the room from the open flue of
gas or other fuel-burning appliances.
•Do not allow any thermal insulation to cover any part of the rear of the appliance. A minimum of 100mm clearance
must be maintained between the fan unit and insulation.
•Ensure the thermal insulation does not obstruct the airflow.
•There must be an adequate source of external air to ensure the rated performance.
•The wall switch should not be installed where it can be touched by someone within a bath or shower.
Installation Directions
STEP I – Preparation and identify the installation location:
1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material. (Refer to the part list to check all accessories provided)
2. Check whether the product has been damaged during transport. Do not operate/install any product which appears
damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
3. Identify suitable locations to install the inlet grill (Sold separately SKU# 209041 - 209046), exhaust fan and the
outlet grill. Take care to avoid structural elements and existing wiring when identify the location.
STEP II – Installation of the fan unit and duct kit
1. Switch off the mains power before any installation.
2. Loosen the locking screws on the plastic clasps.
3. Remove the main body by unclipping the plastic clasps and lifting the main body out of the housing base. (Fig.1)
4. Secure the housing base to a suitable mounting point using the mounting holes in the base. (Fig.2)
NOTE: Check and ensure the body is mounted firmly to reduce vibrations.
5. Fit the main body back to the clasp and tighten the locking screws. (Fig.3)
NOTE: Ensure the airflow direction arrow on the cover of the terminal box is pointing towards the outlet.
6. Attach the flexible ducts to the inlet and outlet side of the motor unit. Secure the duct with the strap provided.
7. Install the inlet grill (Sold separately SKU# 209041 - 209046) and the outlet grill (included, Φ155mm cut out) in the
desired location.
8. Stretch the ducts out and attach them to inlet & outlet grills. Secure the duct with the strap provided.
Parts List
(1) Inline Fan unit
(2) 3 x straps for fixing the duct
(3) 1 x Outlet grille & strap
(4) 3-speed wall switch
(5) 1 x 3M duct
(6) 1 x 1M duct

Installation Instructions
3 | P a g e v 1 . 0 ( 1 1 / 2 0 1 9 )
STEP III - Wiring
9. Install the 3-speed wall switch (provided) in the desired location.
10. Open the cover of the terminal box by unscrewing the four screws.
11. Insert the supply cable through the cable entry and connect the wirings according to the wiring diagram. (Fig.5)
NOTE: The terminals marked ‘X’ are NOT for connection.
12. Loose the screws of the cord anchorage. Place the supply cable in the cord anchorage then secure by tightening
the screws.
13. Close the cover of the terminal box. Then secure the terminal box by tightening the four screws.
14. Switch on the power to test the exhaust fan.
Fig.4 Clearance diagram

Installation Instructions
4 | P a g e v 1 . 0 ( 1 1 / 2 0 1 9 )
Specifications
SKU # 209040
Colour White
Insulation class Class II
IP rating IPX2
Rated voltage 220-240V~, 50Hz
Rated wattage H: 45W, M: 30W, L: 14W
Max. Airflow H: 464 M
3
/H, M: 365 M
3
/H, L: 199 M
3
/H
Overall dimensions H: 248mm W: 300mm D: 200mm
Cut-out size of the outlet grille Φ155mm
Exhaust outlet / Duct size Φ150mm (2 x Duct kits included – 3M & 1M)
Wall switch 3 speed
Weight 3kg
Compatible inlet grille Lucci sku# 209041, 209042, 209043, 209044, 209045, 209046
Fig.5 Circuit diagram
N H X X