LUCCI Air Airfusion Newport User manual

V1.0-EU (11/2019)
LUCCI
NEWPORT
DC CEILING FAN
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Airfusion Newport Installation Instructions
1 | P a g e
V1.0-EU (11/2019)
NEWPORT
THANK YOU FOR PURCHASING
Thank you for purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power
which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and
silent operation.
Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to 65%
more energy than ceiling fans with traditional AC motors.
Silent operation –This DC fan motor is programmed with a stabilized current which efficiently reduces motor
noise.
Low operating temperature –The DC power is managed effectively which brings down the motor operating
temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the
longevity of the motor.
6 speed remote control - Regular AC ceiling fans usually come with only 3 speeds, this DC fan comes
complete with a 6 speed remote, which gives a greater choice of comfort levels.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning the use of the appliance in a safe way and understand the
hazards involved. Cleaning and maintenance shall not be undertaken by children without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE
DISCONNECTION MUST BE INCORPORATED INTO THE
FIXED WIRING IN ACCORDANCE WITH THE WIRING
RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting

Airfusion Newport Installation Instructions
2 | P a g e
V1.0-EU (11/2019)
NEWPORT
the minimum electrical safety of this standard.
Please note warranty will be void if installation is without a
means for an all-pole disconnection incorporated in the fixed
wiring in accordance with the wiring rules.
Example: If a fan is connected to a circuit that can be
isolated via an all-pole safety switch at the switchboard,
then this is considered to be an all-pole disconnection to the
ceiling fan electrical circuit, meeting the requirements of
clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input
of remote control must also be included in the wiring,
and located the same room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 20kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m
above the floor in Australia.
8. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2
walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in
a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty.
Mounting the fan in a situation where it is subject to water or moisture is dangerous and may increase the
risk of damage, injury or electrical shock.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the
manufacturer, its service agent or suitably qualified persons.

Airfusion Newport Installation Instructions
3 | P a g e
V1.0-EU (11/2019)
NEWPORT
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension
system shall be performed by the manufacturer, its service agent or suitably qualified persons.
PARTS LIST
Unpack your ceiling fan carefully. Remove all parts and hardware.
Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
Examine all parts, you should have the following:
1
Mounting bracket x 1
7
Remote controller, Battery, and holder
x 1 set
2
Fan assembly x 1
8
Suction cup x 1
3
Light kit x 1
9
Light kit extension cable x 1
4
Fan blades x 4
5
Installation screws and balancing kit x 1 set
6
Remote receiver x 1
Fig. 1

Airfusion Newport Installation Instructions
4 | P a g e
V1.0-EU (11/2019)
NEWPORT
INSTALLING THE FAN
TOOLS REQUIRED:
- Phillips / flat head screwdriver
- Pair of pliers
- Adjustable spanner
- Step ladder
- Wire cutter
- Wiring, supply cable as required by local provincial and national wiring codes and regulations
INSTALLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the
blade to the nearest objects or walls.
Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 20kg,
with two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
Fig. 2
20 KG

Airfusion Newport Installation Instructions
5 | P a g e
V1.0-EU (11/2019)
NEWPORT
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 15 degree angled ceiling installation. (Fig. 3)
INSTALLATION OF BLADE (Fig.4)
1. Insert the blade into the slot of rotating member of fan motor assembly.
2. Align and engage the holes of the blade to the blade bracket.
3. Secure the blade to the fan motor assembly by tightening the 3 blade screws and washers.
Ensure all screws are tightened evenly to reduce the chance of warping or unbalancing.
Take care not to over tighten the screws, as this can damage the blades
4. Repeat the same process for the other blades.
INSTALLATION OF LIGHT KIT (Fig.5)
NOTE: The light kit must be installed by a licensed electrician.
Loose the 3 screws (1) from the fan assembly. (Fig.5.1)
Remove the heat shrink tube on the quick connector (2) of the light kit then connect to the fan assembly.
Remove the bottom cover (3). (Fig.5.2)
Install the light kit to the fan assembly by tightening the 3 screws. (Fig.5.3)
Use the suction cup to assist with the installation of the GX53 lamp install (4) (Not included) to the lamp
holder. Do not excess the maximum power rating. (Fig.5.3)
Fig. 3
15°
Fig. 5.1
Fig. 4
Fig. 3

Airfusion Newport Installation Instructions
6 | P a g e
V1.0-EU (11/2019)
NEWPORT
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on
the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig.6)
ELECTRICAL WIRING DIAGRAM THE FAN
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN
ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN
PROGRAMMING THE REMOTE AND RECEIVER TO PAIR TOGETHER.
Note: If a down rod extension is used, the Light kit extension cable (item 9, of Fig.1) is required.
See Fig. 7 for instructions below to wire up the fan.
Connect “LIVE”supply wire to the “L” of terminal block on the mounting bracket.
Connect “NEUTRAL” supply wire to the “N” of terminal block on the mounting bracket.
Fig. 6

Airfusion Newport Installation Instructions
7 | P a g e
V1.0-EU (11/2019)
NEWPORT
Connect “EARTH” wire to the “ ” of terminal block on the mouthing bracket.
Hang the fan (Refer to “hanging the fan” Fig. 6, page 6).
Plug connector from the supply wiring from the mounting bracket to the input of the DC motor
driver/receiver.
Plug the light connector and the fan connector from the DC motor driver/receiver to the input wires of
the fan motor and the light kit.
Carefully insert the Remote Receiver above the hanger ball in the remainder spacing in the
mounting bracket. Take care not to damage or loosen any of the wiring.(Fig. 8).
Fig. 7
To fan motor
and light
Fig. 7

Airfusion Newport Installation Instructions
8 | P a g e
V1.0-EU (11/2019)
NEWPORT
FINISHING THE INSTALLATION
INSTALLATION OF THE CANOPY (Fig.9)
1. Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s
accessible metal body back to the earth terminal at the terminal block on the mounting bracket.
2. Loosen the 2 screws at the bottom of the mouthing bracket.
3. Slide the canopy up to the mounting bracket and align the key holes on the canopy with the screws on the
mounting bracket. Turn the canopy until it locks into place with the narrow section of the key holes and
secure it by tightening the two screws. Avoid damaging the electrical wiring prepared previously.
INSTALLATION OF THE REMOTE CONTROL HOLDER (Fig. 10)
Fig. 9
1. Locate a suitable wall to fix the remote control
holder with the 2 screws. (Fig.10a).
2. Slide the remote into the holder. (Fig. 10b)

Airfusion Newport Installation Instructions
9 | P a g e
V1.0-EU (11/2019)
NEWPORT
USING YOUR CEILING FAN
REMOTE CONTROL (Fig.11)
PAIRING REMOTE AND RECEIVER –WHEN 1 DC CEILING FAN IS INSTALLED IN ONE LOCATION
NOTE: Ensure that you have installed a single pole disconnection switch in the fixed wiring for the fan.
NOTE: Ensure power to the receiver is ON prior to pairing the remote with the receiver.
Turn OFF the mains supply to the fan by on/off wall switch.
Fig. 9
Fig. 11
(1) Reverse control
(2) Natural wind (The fan speed automatic cycle
between 1 to 6 speed)
(3) Speed control
(4) Light On/Off
(5) Fan On/Off
(6) 1.5V AAA battery x 2 pcs (Included)