Lucent Technologies SPIRIT 2448 Instruction Manual

Lucent Technologies
Bell Labs Innovations
SPIRIT
®
Communications System
Model 2448
Administration Manual
999-500-235
105772644
Issue 5
June, 1989

LIMITED WARRANTY AND LIMITATION OF LIABILITY
AT&T Information Systems, Inc. ("AT&T") warrants to you that your SPIRIT
®
Communications System ("SPIRIT system")
will be free from defects in material and workmanship when title to your SPIRIT system passes to you. If you notify AT&T
that your SPIRIT system fails to operate as warranted within one year of the date title to your SPIRIT system passes to you,
AT&T will, at its option, repair or replace the component or components of your SPIRIT system that fail to operate as warranted.
Any repair or replacement components may be new or refurbished and will be provided on an exchange basis. If AT&T determines
that your SPIRIT system component cannot be repaired or replaced, AT&T will refund the purchase price to you.
If you purchased your SPIRIT system directly from AT&T, AT&T will perform warranty repair on your premises in accordance
with the terms and conditions of AT&T’s "Business Day" or "Around-the-Clock" warranty plans depending on which you have
selected. The details of AT&T’s warranty plans may be obtained by calling or writing to AT&T. If you purchased your SPIRIT system
from an Authorized AT&T Dealer, you will be covered by AT&T’s Authorized Dealer Warranty Plan during the warranty period.
Contact your Authorized Dealer for details of AT&T’s Authorized Dealer Warranty Plan. AT&T’S OBLIGATION TO REPAIR,
REPLACE OR REFUND IS AS SET FORTH ABOVE AND IS YOUR EXCLUSIVE REMEDY.
The limited warranties provided above do not cover damages, defects, malfunctions or product failures caused by:
– Failure to follow AT&T’s installation, operation or maintenance instructions;
– Failure to provide an appropriate electrical environment for the equipment;
– Unauthorized modification or alteration of the SPIRIT system or its components;
– Product abuse, misuse or the negligent acts of persons not under the reasonable control of AT&T, or;
– Actions of third parties and acts of God other than power surges.
This limited warranty applies only to a SPIRIT system purchased directly from AT&T or purchased directly from an Authorized
AT&T Dealer. This limited warranty does not apply to SPIRIT systems purchased or operated outside the United States.
You may be required to provide AT&T with proof of purchase before AT&T will perform any warranty repair or provide any
warranty replacements.
EXCEPT AS SPECIFICALLY SET FORTH ABOVE, AT&T, ITS AFFILIATES, SUPPLIERS AND DEALERS MAKE NO
WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
EXCEPT FOR PERSONAL INJURY, THE LIABILITY OF AT&T, ITS AFFILIATES, SUPPLIERS AND DEALERS FOR ANY CLAIM,
LOSS, DAMAGE OR EXPENSE FROM ANY CAUSE WHATSOEVER, REGARDLESS OF THE FORM OF THE ACTION,
WHETHER IN CONTRACT, TORT OR OTHERWISE, SHALL NOT EXCEED THE LESSER OF DIRECT DAMAGES PROVEN
OR THE REPAIR OR REPLACEMENT COST OF THE SPIRIT SYSTEM OR THE SPIRIT SYSTEM’S PURCHASE PRICE. IN
NO EVENT SHALL AT&T, ITS AFFILIATES, SUPPLIERS AND DEALERS BE LIABLE FOR INCIDENTAL, RELIANCE, CON-
SEQUENTIAL OR ANY OTHER INDIRECT LOSS OR DAMAGE (INCLUDING LOST PROFITS OR REVENUES SUSTAINED
OR INCURRED IN CONNECTION WITH THE SPIRIT SYSTEM). THIS LIMITATION OF LIABILITY SHALL SURVIVE FAILURE
OF THE EXCLUSION REMEDY SET FORTH IN THE LIMITED WARRANTY ABOVE.
This limitation of liability shall apply to all users of SPIRIT systems and shall apply whether or not the above limited warranty applies.
INSTALLATION/MAINTENANCE INFORMATION
There are several types of installation and maintenance plans available from AT&T and/or your dealer. Please call your AT&T
sales representative or authorized dealer for details.
For warranty service, contact your authorized dealer or call the AT&T Hoteline listed below.
You may place your
AT&T Sales and Service
Label here
Prior to calling the Hotline refer to the Testing and Troubleshooting pages in the Customer Installation Instructions.
Record the following information:
AT&T Account Number
Number of outside/PBX lines
Number of telephones

Table of Contents
Parts of the System 2
Parts of the Telephone Used in Administration 3
Groups and Intercom Extensions 3
How to Use this Manual 4
SECTION 1 Customizing 5
Description of Features that May be Customized 5
How to Use the System Planner and the Customization Chart 7
System Planner 8
Customization Chart 10
How to Customize 12
Confirmation and Error Tones 12
Instructions for Customizing 13
Kinds of Customization
System Reset to Factory-Set Values - 0 14
System Customization - 1 15
Telephone Customization - 2 18
System SpeedCall - 3 23
SMDR Call Report - 4 25
Printing Customization Information - 5 27
SECTION 2 Additional Information 30
Ringing Options 30
System Changes 30
Using with a PBX Centrex System 30
L A Jacks (Dedicated Lines and Power Failures) 31
Optional Equipment 31
Additional Feature Information 32
Helpful Hints 34
System SpeedCall Directory 35
Intercom Extension and Group Directory 36
Index 37
NOTICE: While reasonable efforts were made to ensure that the information in this
document was complete and accurate at the time of printing, Lucent Technologies
assumes no responsibility for any errors. Changes or corrections to the information
contained in this document may be incorporated into future re-issues.
Intellectual property related to this product (including trademarks) and registered to
AT&T Corporation has been transferred to Lucent Technologies Incorporated.
Any references within this text to American Telephone and Telegraph Corporation
or AT&T should be interpreted as references to Lucent Technologies Incorporated.
The exception is cross references to books published prior to December 31, 1996,
which retain their original AT&T titles.
Lucent Technologies – formed as a result of AT&T’s planned restructuring –
designs, builds, and delivers a wide range of public and private networks,
communication systems and software, consumer and business telephone systems,
and microelectronic components. The world-renowned Bell Laboratories is the
research and development arm for the company.
Administration Manual 1

Parts of the System
The SPIRIT
® Communications System, Model 2448, consists of a CONTROLLER that controls
the system, TELEPHONES, and some optional equipment. Outside telephone lines from your
local telephone company or from a PBX, or switchboard, system are connected to the controller.
The controller is connected to all the telephones in the system.
CONTROLLER
Inside Cover:
MUSIC ON HOLD
MUSIC ON HOLD VOLUME CONTROL
SMDR JACK
(Station Message
Detail Recording)
EXTERNAL ALERT
LA JACKS (Line Auxiliary)
Dedicated Lines for computer modems,
answer/record machines, and for
use during power failures.
NETWORK INTERFACE JACKS
(Incoming Telephone Lines)
LOUDSPEAKER PAGING SYSTEM
(optional)
TELEPHONES (STATIONS OR
INTERCOM EXTENSIONS)
(Both 6-button and 24-button
telephones or intercom extensions
may be used with the system.)
Telephones are installed in groups of up to
8 per group. Station 10, which is used for
customization must be a 24-button set.
48-BUTTON ATTENDANT ADJUNCT
(optional)
Provides 48 intercom extension buttons for
one-button dialing of all the intercom
extensions in the system. Also provides feature
buttons for sending and canceling messages
and for turning night service on and off.
2 Administration Manual

Parts of the Telephone Used in Administration
LINE BUTTONS and
INDICATOR LIGHTS
Used to customize Iine-by-line features.
INTERCOM BUTTONS and
INDICATOR LIGHTS
Used when beginning System
Administration.
SPEAKER BUTTON and
INDICATOR LIGHT
Used to turn the speakerphone on
and off.
DIAL
Used to enter numbers and symbols that
must be ‘dialed’ during System Administration.
MEMORY BUTTON
Used to store SpeedCall numbers.
Groups and Intercom Extensions
Each telephone in the system has a 2-digit intercom
extension number. The intercom extensions are grouped
according to the numbers on the right. Groups are used for
some features, such as group paging and picking up a call
within a group. Consider carefully how intercom extension
numbers are assigned to the people in the system so that
the group features are used most efficiently for your
company. The numbers do not have to be consecutive; for
instance, you may have intercom extensions 10 through
15, 18 through 22, and 28 through 33 in your system,
depending on the telephone capacity of your system.
Administration Overlay
LINE NUMBERS
Line number the button represents during
Iine-by-line customization.
ENTER ADMIN
Used to choose another kind of
customization.
COPY TO
Used to duplicate customization of one
telephone to another.
DROP
Used for removing PBX/Centrex Line
Access Codes.
FEATURE
Used to begin customization of
another feature.
STATION
Used to begin customization of
another telephone.
ADD
Used for adding PBX/Centrex Line
Access Codes.
Intercom Extension Group
Numbers
Number
10-17
61
18-25
62
26-33
63
34-41
64
42-49
65
50-57
66
NOTE: When you assign intercom extension numbers to users, remember that all customization
of the system must be done at telephone set 10, and when users dial 0 (zero) using the intercom,
they reach intercom extension 10.
Administration Manual 3

How to Use this Manual
This manual is divided into two basic sections. Following is a description of the parts of the manual.
Customizing (Section 1)
The SPIRIT Communications System can be customized to fit the needs of your company.
This means that, as the administrator of the system, you will be able to change how some features
operate. The system can be used just as it is installed. You may, however, want to take
advantage of some of the customizing options. You can do as much or as little customizing as
you choose. Section 1 of the manual tells you how to customize the system.
Customization is easy to do and doesn’t have to be permanent. Your system is flexible and easy
to change. As you use the system you may think of other changes you want to make, so don’t be
concerned that you have to make all your customizing decisions right now.
Section 1 includes the six kinds of customization possible. These are:
■ System Reset - 0
The reset procedure describes how to return all customization to the installed, or factory-set
values, except
SpeedCall numbers and Call Report date and time.
■ System Customization - 1
System customization describes how to make changes that are system-wide.
■ Telephone Customization - 2
Telephone customization describes how to make different telephones work in different ways.
■ System SpeedCall - 3
SpeedCall, a number memory, is an important timesaver for your users. There are two kinds of
SpeedCall numbers: Personal and System. Personal numbers are stored by the individual
telephone user and are available only at the telephone where they are stored. System numbers
are stored in the system memory by you and are available at all the telephones in the system.
System
SpeedCall tells you how to store System SpeedCall numbers.
■ SMDR Call Report - 4
SMDR (Station Message Detail Recording) Call Report explains how to set the system to provide
a record of incoming and outgoing calls. If your system includes a printer, personal computer
with appropriate software, or specialized hardware you can take advantage of this feature.
■ Print Customization Information - 5
The call-reporting equipment can be used to print or receive customization information, including
the System SpeedCall directory.
Additional Information (Section 2)
This section includes additional information on features, optional equipment, and how to
make changes in your system.
4 Administration Manual

SECTION 1 Customizing
Following is a list and brief description of the features you can change. There are two kinds of
features, SYSTEM FEATURES and TELEPHONE FEATURES. When you customize a system
feature, you have made a change in the whole system that affects all the telephone extensions.
In this manual, information about system features is always printed with a grey background.
When you customize a telephone feature, the change is made for one telephone only. In this
manual, information about telephone features is always printed with a green background.
Description of Features that May be Customized
System Features (instructions for customizing begin on page 15)
■ AUTOMATIC PRIVACY — This feature prevents others from joining your call without your
permission. If Privacy is On, other people in the system can be added to a call only through
conferencing or a special release of Privacy. If Privacy is
Off, another user can join a telephone
conversation by pressing the line button that the call is on or by dialing a dial code (see
User Manual).
(Possible settings are On and Off. Installed setting is On.)
■ TOLL CALL CHECK — If you are in an area that requires a "1" before every toll call, leave this
at the preset value of
1 Required. If your local telephone service does not require a "1" before
dialing a toll call, change the setting to
1 Not Required. If you must dial an access digit in
order to make an outside call, you have PBX or Centrex lines. If you have PBX or Centrex
lines, the
SPIRIT system, will not check for a toll call until after the code is dialed, if the
PBX/Centrex code and lines are correctly customized. Calls will be checked only for telephones
that have been customized as Toll Restricted. (Possible settings are 1 Required and 1 Not Required.
Installed setting is 1 Required.)
■ HELD CALL REMINDER — The system can remind a user that a call is on hold. You can set
the number of minutes it will wait before providing the reminder. (Possible settings are Zero
for no reminder, One, Two, Three, and Four Minutes. Installed setting is One Minute.)
■ LINE TYPE — All incoming lines are either PBX/Centrex Lines or direct Outside Lines. If your
system is not at incoming-line capacity you have
Unavailable Lines. (For example, if you have 11
incoming lines on a system that has 12 incoming line jacks on the controller, line 12 is
Unavailable). Find out how many incoming lines you have, and customize Unavailable Lines as
such for proper operation of AUTOMATIC LINE SELECTION.
(Possible settings are Unavailable
Line, Outside Line, and PBX/Centrex Line. Installed setting is Outside Line.)
■ PBX/CENTREX LINE ACCESS CODES — If you have PBX/Centrex lines, a code is necessary to
dial an outside call. By entering the code(s) required, you will allow the SPIRIT system to
check for toll calls and to automatically insert pauses in
SpeedCall numbers on PBX/Centrex
lines. (Up to four one- or two-digit codes may be entered. One code, the digit 9, is already
installed for your convenience, but may be removed or changed.)
■ EXTERNAL ALERT — If an optional external alerter (buzzer) is part of your system, you can
set when it will turn on for each line. (Possible settings are No Alert, Night Only, Day Only,
and Always On. Installed setting is Night Only.) NOTE: Night Only and Day Only are
determined by whether Night Service is on or off (see User Manual).
■ DIAL TYPE — Set each line for the kind of service you have with your local telephone
company.
(Possible settings are Touch Tone and Dial Pulse. Installed setting is Dial Pulse.)
Administration Manual 5

Telephone Features (instructions for customizing begin on page 18)
Telephone customization is used to make different telephones in the system work in different ways.
■ LINE BUTTON ASSIGNMENTS — The telephones in your system have six or twenty-four
buttons that can be line buttons assigned by you or multi-purpose buttons that the user programs
(see User Manual). When you have assigned a line to a button, that button cannot be used
for anything else unless you change the customization for that telephone.
You can assign any outside line to a button on any telephone. The system determines to what
button the line will be assigned (ascending order, starting with button 1 — see page 9). The
installed setting assigns the first 12 lines to the first 12 buttons on 24-button sets and the first
6 lines to the 6 buttons on a 6-button set. If you have fewer than 12 lines, for proper operation
"remove" the "lines" you don’t have (See page 20). Remember, the more line buttons you
assign to a telephone, the fewer
SpeedCall and Intercom Extension buttons the telephone can
have. After a line is assigned to a button, the user can select the line by pressing the button. If a
line is not assigned to a button on a particular telephone, the user can select the line by dialing
a code (see User Manual).
■ LINE USE PERMISSION — You can assign to each line of each telephone one of the following
permissions. All lines may be customized for LINE USE PERMISSION, including those lines not
assigned to buttons on the telephone.
● No Permission. The telephone may not use that line at all except when a call on that line
is transferred to it.
● Full Permission. The user may place and answer calls on that line. (Installed setting)
● Answer Only Permission. The user may answer calls or retrieve held calls on that line.
■ AUTOMATIC LINE SELECTION — This feature provides the dial tone when you pick up the
receiver, without having to first select a line by pressing a line button. The SPIRIT system has
been factory set to assign Line 2 as the first choice for outgoing calls. This cannot be changed.
Customizing all lines as Not Eligible will mean that the user must select a specific line every time
a call is made. A line that is assigned to a line button and has
Full Permission can be set as
Eligible, which means it can be used by simply picking up the receiver, or Not Eligible, which
means the line button will have to be pressed first to use that line. If lines that are not assigned
to buttons on the telephone are set as
Eligible for AUTOMATIC LINE SELECTION, the setting
is ignored.
(Installed setting is Eligible.)
■ LINE RINGING OPTIONS — You can assign to any line (with Full or Answer Only Permission)
of any telephone one of the following ringing options for incoming calls.
● No Ring. The line does not ring for incoming calls.
● Normal Ring. The line rings normally. (Installed setting)
● Abbreviated Ring. The line rings for 12 seconds only.
● Delayed Ring. The line does not start ringing until 12 seconds after the call comes in.
■ NIGHT RINGING — You can assign to each telephone one of the following options. The options
you assign are in effect when Night Service (see User Manual) is on.
● Normal Ring at Night. When Night Service is on, the telephone will disregard customized
LINE RINGING OPTIONS and ring normally for all permitted lines.
● Customized Ring at Night. The telephone will ring the same whether Night Service is on or off.
(Installed setting).
6 Administration Manual

Telephone Features
■ OUTSIDE SERVICE — This feature determines the kinds of outside calls that may be made
from each telephone. The three choices are the following:
● Outward Restricted. No outside calls may be placed at that telephone except 911 and
unrestricted System
SpeedCall numbers. (see page 23).
● Unrestricted. Calls may be placed at that telephone with no restriction. (Installed setting)
● Toll Restricted. No toll calls may be placed at that telephone except unrestricted System
SpeedCall numbers — see page 23.
System SpeedCall Numbers (instructions for customizing begin on page 23)
The System SpeedCall memory allows you to store telephone numbers that can be dialed by
the users of the system with a two-digit code (30-99).
SMDR Call Report (instructions for customizing begin on page 25)
Call Report explains how to set the system to list outgoing, and, if you want, incoming calls.
If your system includes a printer, personal computer with appropriate software, or specialized
hardware you can take advantage of this feature. You must enter the day and time when this
equipment is installed at the SMDR jack.
■ DAY OF WEEK — This sets the day portion of a clock so the correct day can be printed.
■ TIME OF DAY — This sets a clock so the correct time can be printed.
■ REPORTED CALL DURATION — Decide what length call you want reported. Calls under thirty
seconds are probably not completed calls. (Installed setting is 30 seconds)
■ INCOMING CALL REPORT — Enable or Disable reporting of incoming calls (Installed setting
is Enabled)
Print Customization Information (instructions begin on page 27)
If you have a printer, personal computer with appropriate software, or specialized hardware
installed at the SMDR jack you can list all customizing information, including the System
SpeedCall directory.
How to Use the System Planner and the Customization Chart
A System Planner is provided on pages 8 and 9 to guide you in planning how you will customize
your system. The System Planner is not only a useful guide in the decision-making process of
setting up your system, but also provides a valuable record of the system. The planner should
be changed each time the system is changed.
Record your system-wide decisions on the first page or a copy of the first page of the planner.
You may want to use pencil so that you can make changes in the future. Make a copy of the
second page of the planner for each telephone in your system. Using one copy of the telephone
section of the planner for each telephone in your system, record your telephone customization
decisions.
When the System Planner is complete you can start customizing your system. After becoming
familiar with the confirmation and error tones (see page 12), the customization chart on pages
10 and 11 may be all you will need to complete the customization of your system. More
detailed instructions, however, begin on page 12.
If you use the customization chart on pages 10 and 11, remember to follow the dotted line path.
As on the System Planner, grey-shaded areas are the system features and green-shaded areas
are the telephone features.
Administration Manual 7

System Planner
INCOMING LINES
Use this page to plan the customization
for your system. Permission is granted to
make a copy of this page to record your
decisions for the whole system.
Telephone Number of Line
Line 01
Line 02
Line 03
Line 04
Line 05
Line 06
Line 07
Line 08
Line 09
Line 10
Line 11
Line 12
Line 13
Line 14
Line 15
Line 16
Line 17
Line 18
Line 19
Line 20
Line 21
Line 22
Line 23
Line 24
SYSTEM CUSTOMIZATION
AUTOMATIC PRIVACY
1 Privacy Off
2 Privacy On †
TOLL CALL CHECK
1 1 Required †
2 1 Not Required
HELD CALL REMINDER
0 0 minutes
1 1 minute †
2 2 minutes
3 3 minutes
4 4 minutes
LINE TYPE
1 Unavailable
2 Outside†
3 PBX/Centrex
Line 22 Line 23
Line 24
Line 19 Line 20
Line 21
Line 16 Line 17 Line 18
Line 13 Line 14 Line 15
Line 10 Line 11 Line 12
Line 07 Line 08 Line 09
Line 04 Line 05 Line 06
Line 01 Line 02 Line 03
PBX/CENTREX LINE ACCESS CODES
9 †
EXTERNAL ALERT
1 No Alert
2 Night Only†
3 Day Only
4 Always On
Line 22
Line 23
Line 24
Line 19
Line 20 Line 21
Line 16
Line 17 Line 18
Line 13 Line 14 Line 15
Line 10 Line 11 Line 12
Line 07
Line 08 Line 09
Line 04
Line 05 Line 06
Line 01 Line 02 Line 03
DIAL TYPE
1 Touch Tone
2 Dial Pulse†
CALL REPORT
DAY OF WEEK
(Enter digit 1-7, 1 is Sunday)
Installed setting:
?
TIME OF DAY
Enter 4-digit time, 24-hour format)
Installed setting: 99:99
REPORTED CALL DURATION
(Enter digit 109)
(1 is ten seconds)
Installed setting: 3 (30 sec.)
INCOMING CALL REPORT
1 Disabled
2 Enabled †
SYSTEM CONFIGURATION
(Larger version on page 36)
STATION LOCATION GROUP
10 61
11 61
12
61
13 61
14 61
15 61
16 61
17 61
18 62
19 62
20 62
21 62
22 62
23 62
24 62
25 62
26
63
27 63
28 63
29 63
30 63
31 63
32
63
33 63
34 64
35 64
36 64
37 64
38 64
39 64
40 64
41 64
42 65
43 65
44 65
45 65
46 65
47 65
48 65
Line 22
Line 19
Line 16
Line 13
Line 10
Line 07
Line 04
Line 01
Line 23
Line 20
Line 17
Line 14
Line 11
Line 08
Line 05
Line 02
Line 24
Line 21
Line 18
Line 15
Line 12
Line 09
Line 06
Line 03
49 65
50 66
51
66
52 66
53 66
54 66
55 66
56
66
57
66
† Installed Setting
8 Administration Manual

System Planner
TELEPHONE CUSTOMIZATION
TELEPHONE(S) LOCATION(S)
GROUP(S)
Make a copy of this page for every different Telephone Customization. Complete one page for each
telephone or group of telephones that will be customized identically.
LINE BUTTON
ASSIGNMENTS
LINE USE
PERMISSION AUTOMATIC LINE SELECTION
LINE RINGING
OPTIONS
Check below the lines
assigned to buttons on
telephone(s). Installed
setting is lines 01-12
Assigned and lines
13-24 Not Assigned
1
2
3
No Permission
Full Permission †
Answer Only
1
2
Not Eligible
Eligible †
1
2
3
4
No Ringing
Normal Ringing †
Abbreviated Ringing
Delayed Ringing
Line 01
Line 02
Line 03
Line 04
Line 05
Line 06
Line 07
Line 08
Line 09
Line 10
Line 11
Line 12
Line 13
Line 14
Line 15
Line 16
Line 17
Line 18
Line 19
Line 20
Line 21
Line 22
Line 23
Line 24
† Installed Setting
The system assigns the lines
to buttons in numerical order,
starting with the lowest numbered
line on the lower left button and
proceeding left to right.
Using the Line Button Assignments
above, write on the button chart
at the right the lines you have
assigned to the telephone(s).
Line
Button 22
Line
Button 23
Line
Button 24
Line
Button 19
Line
Button 20
Line
Button 21
Line
Button 16 Line
Button 17
Line
Button 18
Line
Button 13
Line
Button 14
Line
Button 15
24-
button
set
Line
Button 10
Line
Button 11
Line
Button 12
Line
Button 7
Line
Button 8 Line Button 9
6-
button
set
NIGHT RINGING
1 Normal Ring
2 Customized Ring †________
OUTSIDE SERVICE
1 Outward Restricted____
2 Unrestricted †
3 Toll Restricted
Line
Button 4 Line
Button 5 Line
Button 6
Line
Button 1 Line Button 2 Line
Button 3
Administration Manual 9

Customization Chart
At Telephone Set 10
Press INTERCOM
Guide for use on page 11.
Press SPEAKER
Dial * 9 2 4 4 8
Install Administration Overlay
SYSTEM CUSTOMIZATION TELEPHONE CUSTOMIZATION
SYSTEM RESET
Dial 1
Dial 2
(to return to installed settings)
Dial 0
AUTOMATIC PRIVACY
Press STATION
Dial intercom extension number
Press FEATURE
Dial 1
Dial 09009
(all telephones must be idle)
LINE BUTTON ASSIGNMENTS
Dial—
1 Privacy Off
2 Privacy On †
Press FEATURE
Dial 1
Press line button(s)
TOLL CALL CHECK
Dial—
1 Remove Line
2 Assign Line
Press FEATURE
Dial 2 Required †
Dial—
1
2
1
1
Not Required
LINE USE PERMISSION
Sample
Administration Overlay
Press FEATURE
Dial 2
HELD CALL REMINDER
Press line button(s)
Press FEATURE
Dial 3 Dial—
1 No Permission
2 Full Permission †
3 Answer Only
22 23 24
No reminder
1 minute †
1920 21
Dial—
0
1
2
3
4
2 minutes
3 minutes AUTOMATIC LINE SELECTION
4 minutes
16 17 18
Press FEATURE
Dial 3
Press line button(s)
LINE TYPE
13 14 15 Press FEATURE
Dial—
1 Not Eligible
2 Eligible †
Dial 4
10 11 12 Press line button(s)
1
Unavailable
789
Dial— 2 Outside †
LINE RINGING OPTIONS
3
PBX/Centrex
Press FEATURE
Dial 4
Press line button(s)
456
PBX/CENTREX LINE
ACCESS CODES
1231 No Ring
2 Normal Ring †
3 Abbreviated Ring
4 Delayed Ring
Press FEATURE
Dial—
Dial 5
ENTER
ADMIN COPY
TO DROP
To enter a code:
Dial code
Press ADD
NIGHT RINGING
To drop a code:
Dial code
Press DROP
Press FEATURE
Dial 5
FEATURE STATION ADD
To erase all codes:
Dial—
1 Normal Ring
2 Customized Ring †
Press
DROP
Dial ✱
Press DROP
(Installed code is 9)
OUTSIDE SERVICE
Press
FEATURE
Dial 6
EXTERNAL ALERT
Press FEATURE
Dial—
1 Outward Restricted
2 Unrestricted †
3 Toll Restricted
Dial 6
Press line button(s)
Administration Overlay
Dial—
1
2
3
4
No alert
Night Only †
Day Only
Always On
COPY TO TELEPHONE
Press COPY TO
Dial intercom extension number
of telephone to be copied to
DIAL TYPE
COPY TO GROUP
Press FEATURE
Press COPY TO
Dial group number
Dial 7
Press line button(s)
COPY TO ALL
Dial— 1
2
Touch Tone
Dial Pulse † Press
COPY TO
Dial ✱
10 Administration Manual

SYSTEM SpeedCall
Dial 3 CALL REPORT
Dial 4 PRINT CUSTOMIZATION
INFORMATION
Dial 5
ENTER A NUMBER:
●
●
●
Dial telephone number
Press MEMORY
Enter two-digit code
DAY OF WEEK
Repeat these three steps for each
telephone number to be stored.
Press FEATURE
Dial 1
Enter
digit 1-7
(1 is Sunday)
PRINT SYSTEM
CUSTOMIZATION
Press FEATURE
Dial 1
CHANGE A NUMBER:
●
●
●
●
Dial telephone number
Press MEMORY
Enter two-digit code of number
to be changed
Listen for confirmation tone
TIME OF DAY
PRINT TELEPHONE
CUSTOMIZATION
Press
FEATURE
Dial 2
Enter
4-digit time
Press FEATURE
Dial 2
Repeat these four steps for each
telephone number to be changed.
REPORTED CALL DURATION
PRINT SYSTEM
SpeedCall DIRECTORY
Press FEATURE
Dial 3
ERASE A NUMBER:
Press
FEATURE
Dial 3
Enter
digit 1-9 (1 is 10 seconds)
Installed Setting: 3 (30 sec.)
●
●
●
Press MEMORY
Enter two-digit code of number
you want erased
Listen for confirmation tone
PRINT CALL REPORT
INFORMATION
Repeat these three steps for each
telephone number to be erased. INCOMING CALL REPORT
Press FEATURE
Dial 4
Press
FEATURE
Dial 4
Dial—
1
2Disabled
Enabled †
CANCEL PRINTING
Press
FEATURE
Dial #
Guide to Customization Chart
A more detailed set of instructions starts on page 13.
● To get to a different column of features, at ● , press ENTER ADMIN.
● To customize another feature in the same column, press FEATURE.
● To customize another telephone, press STATION.
● To copy the settings on that telephone to another telephone(s) press COPY TO.
● To leave customization hang up and replace overlay in pocket.
● Light patterns indicate current setting:
OFF is 1
ON is 2
Even Flash is 3
Wink (short on, long off) is 4
† Installed setting
Administration Manual 11

How to Customize
Getting Started
When you have finished your plans you are ready to customize the system.
You must do all
customizing from telephone set 10, which must be a 24-button set. You cannot use an attendant
adjunct for customization. For telephone customization, including the COPY functions, the
telephone(s) being customized must not be in use. If you want to reset the system, all
telephones in the system (except set 10) must not be in use, so you will want to choose a time
when people are not using their telephones.
If you want, you can plan for future needs while you customize. If your system is not at
capacity (for instance, you have 18 lines and 30 telephones in your
SPIRIT system now,
but plan to expand to 24 lines and 40 telephones in the future) you may customize the unequipped
lines and extensions now. For proper operation of AUTOMATIC LINE SELECTION, you
should customize LINE TYPE as Unavailable for the unequipped lines.
Confirmation and Error Tones
Throughout this manual you are told that you will receive a confirmation tone after correct
dialing and an
error tone when you have made a mistake. It is important to become familiar
with the confirmation and error tones before you start customizing the system. The following
exercise provides examples of these tones.
● Press INTERCOM. ● Lift handset (or press SPEAKER).
To hear a confirmation tone,
● Dial # 2
To hear an error tone,
● Dial ✱ 0. ● Press MEMORY. ● Dial 28.
12 Administration Manual

Instructions for Customizing
Following are step-by-step instructions for customizing.
■ STEP 1 PRESS ONE OF THE INTERCOM BUTTONS ON TELEPHONE SET 10
An INTERCOM button press times out after five seconds. If more than five seconds elapse
before you proceed to STEP 2, press the INTERCOM button again.
■ STEP 2 PRESS SPEAKER (or lift the receiver)
You will hear a dial tone.
■ STEP 3 DIAL ✱ 9 2 4 4 8
You will hear a confirmation tone. If you do not hear the confirmation tone, hang up and
start over.
■ STEP 4 PLACE ADMINISTRATION OVERLAY
(This step is not necessary if you are going to reset features back to the installed setting or
enter SpeedCall numbers and do no other customization.)
Place the administration overlay on telephone set 10. The overlay is provided in the pocket on
the back cover of this manual. The ENTER ADMIN light will be on to show that the system is
ready for administration. No calls may come in to or go out from telephone set 10 during
customization.
■ STEP 5 CHOOSE KIND OF CUSTOMIZATION
The chart on pages 10 and 11 shows six customizing choices at the top. The chart also shows
what customizable features are reached through each choice. Using the chart as a guide, make
the appropriate choice.
● Dial 0 to reset the system. (All telephones except set 10 must be idle. If a telephone other
than set 10 is in use you will hear a busy tone and the system will not reset.)
● Dial 1 to do System Customization.
● Dial 2 to do Telephone Customization.
● Dial 3 to store or erase numbers in the System SpeedCall memory.
● Dial 4 to customize the SMDR Call Report feature.
● Dial 5 to print customization information.
■ STEP 6 COMPLETE CUSTOMIZATION CHOSEN IN STEP 5
Following the instructions on pages 14-27, complete the customization chosen in STEP 5.
■ STEP 7 BEGIN ANOTHER KIND OF CUSTOMIZATION
To continue with another kind of customization, press the ENTER ADMIN button and repeat
steps 5 and 6. For example, if you complete the desired customization under System Customi-
zation and want to continue with Telephone Customization, press the ENTER ADMIN button
and repeat steps 5 and 6.
■ STEP 8 EXIT CUSTOMIZATION
When you are finished or want to stop customizing, replace the receiver (or press SPEAKER).
Replace the Administration Overlay in the pocket on the back cover of this manual.
Administration Manual 13

System Reset to Factory-Set Values-0
CAUTION: Use of reset eliminates all customization.
If you dialed 0 in STEP 5 on page 13, and if all telephones except the one you are using are idle,
you can reset the system to the installed settings shown on the chart on pages 10-11. If all telephones
are not idle, you will hear the busy signal.
Enter the System Reset code 09009. If you make a mistake you will hear the error tone, and
you must exit and re-enter reset to try again (press ENTER ADMIN and dial 0). If you enter
the reset code successfully you will hear the confirmation tone and and all features except
System
SpeedCall numbers and call report day and time will be returned to installed settings.
Lines 1 through 12 again will be assigned to buttons 1 through 12 on all telephones. If any
telephones were customized so that some of those buttons were multi-purpose, and those
buttons were programmed by the users, one-touch access to Personal
SpeedCall numbers and all
other user programming for those buttons will be lost. User programming of buttons 13 through
24 will be unaffected.
The reset procedure requires up to five seconds. You will hear the confirmation tone after the
procedure is completed.
To exit you may replace the receiver or press SPEAKER, or, if you want to continue customizing
features, press the ENTER ADMIN button to reenter administration at STEP 5 on page 13.
14 Administration Manual

System Customization - 1
If you dialed 1 in STEP 5 on page 13 you began System Customization. The features on the
following pages may be programmed in any order, and you may exit customization at any time,
leaving unchanged features at previously-set values. You may also use System Customization
to check the setting of a feature. You do not have to make changes.
Features are customized by entering a digit, as shown on the following pages. If the digit you
enter is valid, you will hear a confirmation tone and the indicator light(s) will reflect the new
setting. If the digit you enter is not valid, you will hear the error tone and the system will
remain ready to customize that feature until a valid digit is entered or you exit the feature.
No change will be made in a feature until you hear a confirmation tone.
After customizing a feature, you may do any of the following:
● press the FEATURE button to customize another feature
● press the ENTER ADMIN button to go back to STEP 5
● hang up the receiver or press SPEAKER to exit customization
During customization, all the buttons on your 24-button set
at station 10 represent lines. Numbering starts at the lower
left with line 1 (see illustration). When you are customizing
a feature that is not changed on a line-by-line basis, the
Line 1 indicator light will show the current status of the
Line 22
Line 19
Line 16
Line 13
Line 10
Line 07
Line 04
Line 01
Line 23
Line 20
Line 17
Line 14
Line 11
Line 08
Line 05
Line 02
Line 24
Line 21
Line 18
Line 15
Line 12
Line 09
Line 06
Line 03
feature. When you are customizing a feature that is changed
Button Assignments
on a line-by-line basis (line selectable), the status of each line
During Customization
(Telephone Set 10)
will be shown on the indicator light for that line.
When you are customizing features that require a setting for each incoming line in the system,
you do not have to press the FEATURE button for each line. Press all the line buttons for
which you want the same setting.
EXAMPLE: Your system has the capacity for 24 incoming lines. Lines 01 through 10 are
PBX/Centrex Lines. Lines 11 through 20 are Outside Lines. Lines 21 through 24 are not used
(Unavailable).
PROCEDURE: Press FEATURE, then dial 4. Press line buttons 01 through 10. Dial 3.
Press line buttons 21 through 24. Dial 1
(You do not have to customize lines 11 through 20 because the installed setting is
Outside
Line.)
The indicator light of a selected line button will flash rapidly to let you know which line you
are currently customizing. If you have selected a line and then change your mind and do not want
to customize that line, simply press the line button again.
Administration Manual 15

System Customization
■ AUTOMATIC PRIVACY
Press FEATURE. Dial 1.
The indicator light for Line 1 will show the current system-wide privacy status. If the light is
ON, AUTOMATIC PRIVACY is
On. If the light is OFF, AUTOMATIC PRIVACY is Off.
To change the privacy status, enter one of the following:
DIAL
INDICATOR LIGHT SETTING
1OFF
Privacy Off
2ON Privacy On (installed)
■ TOLL CALL CHECK
Press FEATURE. Dial 2.
All the line indicator lights will go OFF. If you are required to dial 1 before placing toll calls,
enter 1; otherwise, enter 2. Possible choices are 1,
1 Required (installed) and 2, 1 Not Required.
■ HELD CALL REMINDER
Press FEATURE. Dial 3.
All of the line indicator lights will go OFF. Enter the number of minutes for the HELD CALL
REMINDER. If you enter 0 the feature is turned off and no HELD CALL REMINDER will be
provided. You may also enter 1, 2, 3, or 4, so that the HELD CALL REMINDER will be provided
after One, Two, Three, and Four Minutes. The installed setting is One Minute.
■ LINE TYPE
Press FEATURE. Dial 4.
Each line indicator light will show the current status for that line. (Line assignments are
labeled on the Administration Overlay and shown in the table on page 15). If a light is ON the
line is set as an Outside Line. If a light is OFF the line is set as an Unavailable Line, that is not
part of your system. You should set as Unavailable, lines that are not part of your system. If the
light is flashing an even flash, the line is set as a
PBX/Centrex Line. To change any individual
line(s), press the line button(s) and dial 1, 2 or 3 (see table, below). You may press more than one
line button to make the change on more than one line. If you dial the number without pressing
a line button first you will hear the error tone. (The system may require up to five seconds to
complete the procedure. You will hear the confirmation tone after the procedure is completed.)
DIAL INDICATOR LIGHT SETTING
1OFF
Unavailable line
2ON Outside Line (installed)
3 Even Flash
PBX/Centrex Line
16 Administration Manual

System Customization
■ PBX/CENTREX LINE ACCESS CODE
Press FEATURE. Dial 5.
All of the line indicator lights will go off.
To ENTER a system-wide PBX/Centrex dial code.
Dial the desired dial code. Press ADD button. You will hear the confirmation tone when the
code is added. If there are already four other codes programmed you will hear the error tone.
The digit
9 is preset as the PBX/Centrex code, so there is room for three other codes. You may,
of course, erase the
9 code if you want.
To ERASE a system-wide PBX/Centrex dial code.
Dial the code you want to erase. Press DROP. You will hear the confirmation tone when the
code is erased. If the code is not there to be erased, you will hear the error tone.
To ERASE all codes.
Press DROP. Dial ✱ . Press DROP. You will hear the confirmation tone if you successfully
followed the DROP procedure.
You may continue to enter or erase codes or you may exit the feature.
■ EXTERNAL ALERT
Press FEATURE. Dial 6.
Each line indicator light will show the current EXTERNAL ALERT status for that line. (Line
assignments are labeled on the system administration overlay and shown in the table on page 15.)
To make changes, press the line button(s) for the line(s) on which you want to make a
particular change and dial one of the digits from the table below. You may press more than
one line button to make the change on more than one line. If you enter a digit without first
pressing a line button you will hear the error tone.
DIAL
INDICATOR LIGHT
SETTING
1OFF
No Alert
2ON
Night Only (installed)
3
Even Flash
Day Only
4
“Wink” (Short ON, Long OFF)
Always On
■ DIAL TYPE
Press FEATURE. Dial 7.
Each line indicator light will show the current DIAL TYPE for that line. (Line assignments are
labeled on the system administration overlay and shown in the table on page 15.) If the
light is OFF, that line is set for Touch Tone dialing. If the light is ON, the line is set for
Dial Pulse dialing. To change the DIAL TYPE for a line or lines, press the line button(s) and
dial the appropriate digit from the table below. You may press more than one line button to
make the change on more than one line. If you enter a digit without first pressing a line button
you will hear the error tone.
DIAL INDICATOR LIGHT
SETTING
1OFF
Touch Tone
2ON
Dial Pulse (installed)
Administration Manual 17

Telephone Customization - 2
If you dialed 2 in STEP 5 on page 13, you began Telephone Customization. The features on the
following pages may be programmed in any order, and you may exit customization at any time,
leaving unchanged features at previously-set values. You may also use Telephone Customization
to check the setting of a feature. You do not have to make changes.
Features are customized by entering a digit, as shown on the following pages, If the digit you
enter is valid, you will hear a confirmation tone, and the indicator light(s) will reflect the new
setting. If the digit you enter is not valid, you will hear the error tone and the system will
remain ready to customize that feature until a valid digit is entered or you exit the feature.
No change will be made until you hear the confirmation tone.
All telephone features are customized on a set-by-set basis, so you must enter the telephone
number before customizing. The changes you make on set 12, for example, will not be made on
set 14, or any other, unless you specifically copy a customizing set-up from one telephone to
another. Making changes via Telephone Customization is not always necessary for all telephones.
You may, for example, want to leave all the telephones except one at the installed setting for
a feature.
EXAMPLE: All of the telephones except set 16 are used by employees who should not be
restricted from placing long distance calls. Set 16, however, is in the lobby, and is used by
company visitors. You might want to set OUTSIDE SERVICE on the lobby telephone
to Toll Restricted, leaving the other telephones Unrestricted.
After customizing a feature, you may do any of the following:
● press the FEATURE button to customize another feature
● press the STATION button to customize another telephone
● press the ENTER ADMIN button to go back to STEP 5 on page 13
● press the COPY TO button to copy the customization of this telephone to another telephone
● hang up the receiver (or press SPEAKER) to finish customization
During customization, all the buttons on your 24-button set represent line buttons. Numbering
starts at the lower left with line 1 (see illustration, page 15). When you are customizing a
feature that is not changed on a line-by-line basis, the Line 1 indicator light will show the
current status of the feature on that telephone. When you are customizing a feature that is
changed on a line-by-line basis (line selectable), the status of
each line of that telephone will show
on the indicator light for that line.
When you are customizing features that require a setting for each incoming line in the system,
you do not have to press the FEATURE button for each line. Press all the line buttons for
which you want the same setting.
EXAMPLE: You are customizing LINE USE PERMISSION and you want to make lines
4, 5, and 6 No Permission and lines 7 and 8 Answer Only.
PROCEDURE: Press FEATURE, dial 2, press line buttons 4, 5, and 6, and dial 1. Press line
buttons 7 and 8 and dial 3.
The indicator light of a selected line button will flash rapidly to let you know which line you
are currently customizing. If you have selected a line and then change your mind and do not
want to customize that line, simply press the line button again.
18 Administration Manual