Madison Park ALBION WRITING DESK User manual

Description QTY
Parts List
Item
P1
P2
Hardware List
QTY
Description
Item
R
Right leg
Left legs
1
1
ASSEMBLY INSTRUCTIONS
Description: ALBION WRITING DESK
Pre-assembly:
Take out all parts and hardware from box.
Do not discard any content until assembly is complete to avoid accidentally discarding small parts or hardware.
Important safety instructions:
Please read carefully all instructions before assembly.
For your safety and ease, assembly by two or more adults is recommended.
Keep instructions for future use.
P3
Top 1
P4
Strecher 1
H1
H2
H3
BOLTS Ø14" x 12L
FLAT WASHERS Ø14"
LOCK WASHERS Ø14"
02
02
02
H4
H5
H6
FLAT WASHERS Ø5 16"
10
10
10
H7 1ALLEN KEY
Page 1 of 2
P2
m
Step 1: Assemble the DESK on a flat, soft surface such as a carpet or cloth to prevent scratching the finish.
Attach right leg (P2) to table top (P3) using Lock washer ( H6), Flat washer ( H5) and Bolt ( H4) as shown below.
Assembly Procedures:
H6
H4
H5
H7
BOLTS Ø 5
16" x 2"L
LOCK WASHERS Ø 5
16"
* DON'T TIGHTEN BOLTS UNTIL STEP 3
(H4) x 5
(H5) x 5
(H6) x 5
FLAT WASHERS Ø5 16"
(H7) x 1 ALLEN KEY
BOLTS Ø 5
16" x 2"L
LOCK WASHERS Ø 5
16"
DISCLAIMER: WHEN PROPERLY ASSEMBLED, THIS ITEM IS SAFE FOR INTENDED USE. SELLER IS NOT LIABLE FOR ANY DAMAGES
RESULTING FROM ITEM BEING IMPROPERLY ASSEMBLED AFTER PURCHASE.

Page 2 of 2
P4
H7
H1
H3
H2
H7
H1
H3
H2
H6
H4
H5
H7
Thank you for your purchase
ADDITIONAL NOTE ABOUT SAFETY: BOLTS MAY LOOSEN DURING NORMAL EVERYDAY USE. THEY SHOULD BE PERIODICALLY INSPECTED AND
RE-TIGHTENED TO PREVENT DAMAGE OR INJURY. ALWAYS CHECK TO ENSURE THAT ALL HARDWARE IS KEPT TIGHTENED.
Step 4: Turn the assemble desk to an upright position. Assembly is complete.
P1
Step 2: Attach metal stretcher (P4) to right leg (P2) using Lock washer (H3), Flat washer ( H2) and Bolt ( H1) as shown below.
Step 3: Attach left leg (P1) to table top ( P3) and metal stretcher (P4) using Allen key (H7), Lock washer (H3), Flat washer ( H2) and Bolt ( H1)
and Lock washer (H6), Flat washer ( H5) and Bolt ( H4) as shown below.
(H1) x 1
(H2) x 1
(H3) x 1
FLAT WASHERS Ø5 16"
(H7) x 1 ALLEN KEY
BOLTS Ø 5
16" x 2"L
LOCK WASHERS Ø 5
16"
(H1) x 1
(H2) x 1
(H3) x 1
FLAT WASHERS Ø5 16"
BOLTS Ø 5
16" x 2"L
LOCK WASHERS Ø 5
16"
(H4) x 5
(H5) x 5
(H6) x 5
FLAT WASHERS Ø5 16"
(H7) x 1 ALLEN KEY
BOLTS Ø 5
16" x 2"L
LOCK WASHERS Ø 5
16"