Madison Park E&E-PALISADES ACCENT CHEST User manual

Page 1 of 5
Description QTY
Parts List
Item
P1
P2
P3
Hardware List
QTY
Description
Item
Pre-assembly:
Take out all parts and hardware from box.
Do not discard any content until assembly is complete to avoid accidentally discarding small parts or hardware.
Important safety instructions:
Please read carefully all instructions before assembly.
For your safety and ease, assembly by two or more adults is recommended.
Keep instructions for future use.
TOP PANEL 1
SIDE PANEL 2
BACK PANEL 1
H1
H2
H4
H5
ALLEN KEY 4 MM
BOLT M6 X 40 MM
LOCK WASHER 6 X 11 X 2
FLAT WASHER 6 X 16 X 2
1
20
20
4
H3 20
P4
P5
SHELF 1
BASE PANEL 1
P6 DOOR
PANEL
2
PEN SHELF
ASSEMBLY INSTRUCTIONS
Description: E&E - PALISADES ACCENT CHEST

Step 1. Assemble the chest on a flat, soft surface such as a carpet or cloth to prevent scratching the finish.
Assembly Procedures:
hardware package
QTY
Description
Item
H6
H7
SCREW JF 6 X 1/2
PHILIP HEAD SCREWDRIVER ( NOT INCLUDE )
4
1
(H1) x 1
(H2) x 4
(H3) x 4
(H4) x 4
ALLEN KEY 4 MM
BOLT M6 X 40 MM
LOCK WASHER 6 X 11 X 2
FLAT WASHER 6 X 16 X 2
A
P1
P6
P6
P5
P3
H1
H4
H3
H2
H1
H3
H4
H2
Step 2: Attach Top panel (P1), Back panel (P3), Door panel (P6), and Base panel (P5) to be main body using
Allen key (H1), Lock washer (H3), Flat washers (H4) and 40 MM Bolt (H2) as shown below.
H8 ANTI TIP KIT 1
ASSEMBLY INSTRUCTIONS
Description: E&E - PALISADES ACCENT CHEST
Page 2 of 5

(H1) x 1
(H2) x 12
(H3) x 12
(H4) x 12
ALLEN KEY 4 MM
BOLT M6 X 40 MM
LOCK WASHER 6 X 11 X 2
FLAT WASHER 6 X 16 X 2
H4
H3
H2
H2
H3
H4
H4
H3
H2
H4
H3
H2 H1
H2
H3
H4
H1
H2
H3
H4
(H1) x 1
(H2) x 4
(H3) x 4
(H4) x 4
ALLEN KEY 4 MM
BOLT M6 X 40 MM
LOCK WASHER 6 X 11 X 2
FLAT WASHER 6 X 16 X 2
H2
H3
H4
H1
P2
P2
Step 3: First open the Drawer from main body, then attach Side panel (P2) to main body using Allen key (H1),
Lock washer (H3), Flat washers (H4) and 40 MM Bolt (H2) as shown below.
Step 4: Close the Drawer to main body, then tighten Side panel (P2) to Back panel (P3) using Allen key (H1),
Lock Washer (H3), Flat washers (H4), and 40 MM Bolt (H2) as shown below.
P2
P2
P3
ASSEMBLY INSTRUCTIONS
Description: E&E - PALISADES ACCENT CHEST
Page 3 of 5

(H5) x 4
(H6) x 4
(H7) x 1
PEN SHELF
SCREW JF 6 X 1/2
PHILIP HEAD SCREWDRIVER ( NOT INCLUDE )
Step 6: For safety, attach Anti tip kit (H8) as shown below.
H7
H6
H5
P4
Step 5: Attach Shelf (P4) to main body using Screwdriver (H7), Pen Shelf (H5),and Screw JF 6 x 1
2 (H6)
as shown below.
a. Screw ø8 x 2”
b. Screw ø8 x 5/8”
c. Restrain Strap
d. Metal Tabs
e. Plastic Wall Anchor
x 1
x 1
x 1
x 2
x 1
db
c
e
a
d
MANDATORY
H8
(H8) x 1 ANTI TIP KIT
ASSEMBLY INSTRUCTIONS
Description: E&E - PALISADES ACCENT CHEST
Page 4 of 5

Step 7: Assembly is complete.
Thank you for your purchase
Disclaimer: When properly assembled, this item is safe for intended use. Seller is not liable
for any damages resulng from item being improperly assembled aer purchase
ADDITIONAL NOTE ABOUT SAFETY: BOLTS MAY LOOSEN DURING NORMAL EVERYDAY USE. THEY SHOULD BE
PERIODICALLY INSPECTED AND RE-TIGHTENED TO PREVENT DAMAGE OR INJURY. ALWAYS CHECK TO ENSURE THAT ALL
HARDWARE IS KEPT TIGHTENED.
ASSEMBLY INSTRUCTIONS
Description: E&E - PALISADES ACCENT CHEST
Page 5 of 5