Mainstays BH18-084-097-45 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-04-09 Rev. 0001-A Factory: KONRIC
Steele Open AV Tower
Stock # BH18-084-097-44 Expresso
# BH18-084-097-45 White
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
where it was purchased. Please call our customer service number and have your instructions and parts list
ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Steele Open AV Tower
MODEL # BH18-084-097-44 / BH18-084-097-45
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 50 lb (22.7 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
GENERAL INFORMATION, TIPS
AND
TRICKS
MAXIMUM LOAD 20 lb (9.1 kg)

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making
sure Cam Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of
Cam Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Side Panel (Qty. 2)
C-Bottom Panel (Qty. 1) D- Partition Panel (Qty. 5)
E- Fixed Shelf (w/o cam lock) (Qty. 2) F- Fixed Shelf (with cam lock) (Qty. 2)
G- Bottom Back Support (Qty. 1) H- Bottom Left Support (Qty. 1) I- Bottom Right Support (Qty. 1)

5
Parts and Hardware List
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel (4) M10 x 40 mm Wood Dowel
(Qty. 16+1 extra) (Qty. 16+1 extra) (Qty. 4+1 extra) (Qty. 68+2 extra)
(5) M15 x 60 mm Wood Dowel (6) 1-3/4” Bolt
(Qty. 8+1 extra) (Qty. 8+1 extra)
(7) Lock Washer (8) Flat Washer (9) Plastic Cap
(Qty. 8+1 extra) (Qty. 8+1 extra) (Qty. 4)
(10) Small Plastic Cap Hex Wrench Glue
(Qty. 14+1 extra) (Qty. 1) (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty.1)
(Not included for BH18-084-097-45) (Inside Plastic Bag)
Tools required: Hex wrench (provided) and Phillips screwdriver and hammer (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw 16 Cam Bolts (2) into the designated small holes on the Side Panels (B), Bottom Panel
(C) and Bottom Supports (H and I).
B
BC
I
H
2
Cam Bolt
(16 used in this step)
②

7
1
3
H
I
G
1
3
M8 x 30 mm Wood Dowel
( 2 used in this step )
Assembly Instructions
3. Connect the Bottom Back Support (G) between the Bottom Side Supports (H and I) by engaging one
Wood Dowel (3) and one Cam Lock (1) in each end.
Cam Lock
(2 used in this step)
①
③

8
Assembly Instructions
4. Connect the Partition Panel (D) between the Fixed Shelves (F) by engaging four M10 Wood Dowel (4) in
each side.
F
F
D
4
M10 x 40 mm Wood Dowel
( 8 used in this step )
④

9
Assembly Instructions
5.Attach the Partition Panel (D) to the previous assembly by engaging eight M10 Wood Dowels (4).
4
D
D
F
F
M10 x 40 mm Wood Dowel
( 8 used in this step )
④

10
Assembly Instructions
6. Attach the Fixed Panel (E) to the Partition Panel (D) by engaging four M10 Wood Dowels (4).
7. Repeat the same procedure to attach the Fixed Panel (E) at the opposite end.
4
E
E
D
D
M10 x 40 mm Wood Dowel
( 8 used in this step )
④