MakerBot Thing-O-Matic User manual

10/24/12 2:04 PM
Makerbot Thing-O-Matic Quick Start Guide
IMPORTANT: Depending on where you are located in the world, you may need to switch the voltage
setting on you power supply. You should make sure it is in the correct position before turning your machine
on. It will most likely arrive in the 110V position. Change it accordingly.
Look over your Thing-O-Matic for any damage from shipment. If you’re checking this page out after
assembling a Thing-O-Matic from a kit, just skip down to the section labeled “Install Software.”
Open your boxes and take a look at what is inside.
There are a lot of extra nuts and bolts. You may never have to use them, but it doesn’t hurt to have
them around.
120mm Wide Kapton Tape for your Heated Build Platform. The tape applied to the build platform will
eventually get scratched or torn. You can use this big roll to replace it.
Gen4 Interface Controller, which you can use to print without being connected to your computer.
USB A to B cable and Power Cord.
Tools: hex keys and wrenches for upkeep and maintenance.
Set up Hardware
It’s time to unpack your MakerBot Thing-O-Matic! The Thing-O-Matic is fully assembled, but you will need
to set up a few things before you can start using your machine.
Bolt Extruder in Place

10/24/12 2:04 PM
When you unpack your Thing-O-Matic, you’ll find the extruder just below the Z-stage, where it has been
immobilized for shipping. All the wiring is complete; you’ll just need to bolt it in place. Put large white
spacers between the extruder and Z-stage.
Once that is in place, secure the extruder with the supplied M5 nuts and bolts.

10/24/12 2:04 PM
Now your extruder is ready to go!
Install Spool Holder
Next, it’s time to install the spool holder that came with your bot. This spool holder was printed on your
Thing-O-Matic as a test before we shipped the machine out to you.
Locate the spool holder and drop 4 M3 bolts in the holes. Then install the holder on the front upper left of
your machine, like this:

10/24/12 2:04 PM
Once it’s in place, secure the spool holder with 4 M3 nuts. Then put the spool in place!

10/24/12 2:04 PM
Good to go!
Plug in Generation 4 LCD Interface
Find your LCD Interface kit. You may need to attach the sides. If so, put the sides in place as shown and
tighten them down with several M3 x 16 mm bolts. The nuts should already be in place.

10/24/12 2:04 PM
Next locate the rainbow cable coming from the inside of the Thing-O-Matic.

10/24/12 2:04 PM
Plug this into the back of the interface board like this.

10/24/12 2:04 PM
Now your interface board is ready to go. We’ll come back to it later.
Install Software
The software that you’ll use to control your Thing-O-Matic is called ReplicatorG and is available
at http://replicat.org. Go there for instructions on how to install the latest version. Note: Some parts of this
section may be out of date. Check the main Software page for more up-to-date information.

10/24/12 2:04 PM
Install Drivers
You may need to install drivers to be able to communicate with your Thing-O-Matic. To determine whether
this is necessary, start ReplicatorG with your Thing-O-Matic unplugged and look at the contents of the the
“Machine” -> “Connection (serial ports)” menu. Now plug in your Thing-O-Matic and choose “Rescan serial
ports” from that “Machine” -> “Connection (serial ports) menu. Navigate back to the list of serial ports —
you should see a new port now that your machine is plugged in. If not, follow the instructions below to
install the necessary drivers.

10/24/12 2:04 PM
Windows:
Navigate to the device manager. The Arduino Mega should be listed under “Ports (COM & LPT).”
If you see an orange icon with an exclamation point next to the Arduino Mega, then you should load your
driver manually.To do this, right click on the Arduino Mega, and select “Update Driver Software” then select
“Browse my computer for driver software.” Browse to the drivers folder in ReplicatorG and select the
Arduino driver. Press OK.
Older Windows systems may need to install the FTDI USB Serial driver to communicate with their Extruder
Controller; this will be found in the same directory as the Arduino Mega driver.
Mac OS X:
There is a /drivers folder in the replicatorg folder you installed. It contains a driver for the FTDI USB->Serial
converter used with Arduino and Sanguino boards. If you have already installed Arduino, you can skip this
step. Otherwise, please install it.
Calibration and Testing
Pre-Run Testing
Open the Control Panel
Click the “Control Panel” button. Here you can move the 3 axes, control your extruder and platform
temperatures, and load and unload plastic filament.

10/24/12 2:04 PM
Move XYZ axes and test endstops
Now, click each of the arrows and make sure that the machine makes the proper movements. The negative
direction for the X and Y axis should run towards the endstops; for the Z-axis, the endstop is at the top, in the
plus direction. Make sure that each axis can run all the way to the endstop.
Calibration Routine
While your Thing-O-Matic was fully calibrated before leaving the factory, it’s a good idea to re-calibrate
after shipping.
Here’s a good video that explains the process.

10/24/12 2:04 PM
Loading Filament and Testing Extrusion
On the right side of the control panel, you will find a tab labeled “Stepstruder MK7.” In this tab, you can see
a realtime readout of the extruder and platform temperature, and you can set target temperatures. In the
rolling readout, the blue line is the target temperature for the extruder head, the red line is the current
temperature for the extruder head, the yellow line is the target temperature for the build platform, and the
white line is the current temperature for the build platform. To heat up the extruder, type “225” into the
“Target Temperature” box and press enter. You should see the red line start to rise.
To heat up the platform, type “120” in the “Platform Target Temperature” box and hit enter. Now, you
should see the white line start to rise.

10/24/12 2:04 PM

10/24/12 2:04 PM
Once the Current Temperatures reach the target temperatures, you can begin loading the filament into the
extruder. Take the filament and push it into the hole that lines up with your extruder’s hot end.

10/24/12 2:04 PM
The filament will stop soon after you insert it. That’s because the drive gear is in the way. To get the filament
into the heating chamber, check that motor speed “RPM” is set to 3, and “Extruder Duration” is set to 30
seconds. Now, press the “Forward” button. This will engage the motor and turn the drive gear.
To help the drive gear catch the filament, you’ll need to apply some pressure to the filament. Hold the
filament between your fingers and press it down until you feel the motor grab the plastic, and make sure to
support the entire Z-stage from below. Remember: the tip of the extruder will be very hot, so be careful!
Sometimes, it will take you more than 30 seconds to load the filament; just click the “Forward” button again
to run the extruder motor for another 30 seconds.
When the drive gear has caught the filament, you’ll be able to feel the filament being drawn into the motor
assembly. A few seconds after that, you’ll begin to see a thread of plastic coming out of the nozzle. Once
you see plastic being extruded by the nozzle, you can move on to the next step: your first print!
Your First Print
Open a “.stl” file in Replicator G.
Download an .stl file and open it up in ReplicatorG. We found this one here:
http://www.thingiverse.com/thing:625

10/24/12 2:04 PM
Choose file from directory

10/24/12 2:04 PM
Move and Resize your Model (if necessary)
Let’s take a look at some of the tools we can use to manipulate the model in Replicator.“View” allows you to
toggle around the printing space.

10/24/12 2:04 PM
“Move” allows you to move the positon of the model in the space. Before generating Gcode for a model, it is
a good idea to click the “Put on Platform” and “Center” buttons. This will make sure that the model is
oriented correctly on the grid.

10/24/12 2:04 PM
“Rotate” allows you to rotate the model over the XYZ axis.

10/24/12 2:04 PM
“Mirror” allows you to mirror the model.