Matatakitoyo Torque Tools META User manual

• Accuracy : C.W. ± 1% / C.C.W. ± 1.5%
• Memory : 50 Readings
• Unit Selection : kg-m, Nm, ft.lb, in.lb
• Operating Temperature : -10℃~55℃
• Storage Temperature : -40℃~85℃
• Humidity : 0~90%
• Battery : 1.5V UM-3 (AA) x 3 ( Do not use low self-discharge battery )
• Operating Mode : Auto Reset Mode & Track Mode & Torque Angle Mode
(See Page-2 Tolerance Setting)
• Warranty : 1 year in normal statement.
1. Before operating this torque wrench study carefully these instructions.
2. Main usage & application digital torque wrench is different from general torque wrench,it has strong operation function including
torque setting, time setting, mode setting, data storage,data clear, data output and user calibration function.
It is easy to operate, it reduce the requirements for the operator by install the digital display.
It is widely used for the automotive industry, machinery industry, such as bolt fastening and control.
3. Over-torquing(109% of Max. Torque range)could cause breakage or lose of accuracy.
4. Keep this digital torque wrench away from magnets. If the wrench gets wet, wipe it with a dry towel soon.
The salt in seawater can damage the wrench.
5. Do not apply excessive force to the LCD screen .
6. The plastic body is not affected by petroleum products but may be damaged by some industrial solvents.
Clean it by clean cloth soaked in mineral spirits or denatured alcohol. Never immerse this wrench or any part of it in any liquid.
BEFORE STARTING
SPECIFICATIONS
PANEL CONTENTS
Manual
Supplied in a plastic box.
Torque wrench
1
1 Buzzer
2 LED indicator (Green)
3 LED indicator (Red)
4 LED indicator (Yellow)
5 LCD panel
6 Set
7 Memo
8 Up / Angle Range Setting
9 Down
Cancel
Power
RS-232 Data out
10
11
12
Battery
Communication
Memo
Setting
Tolerance
Direction
Values
Units
Units
Units
Units
1
2 4 79 11
3 5 6 8 12 10
Manual
TORQUE
1/4” 3/8” 1/2”
S
M
+
-
C
META
OPERATION MANUAL
Digital Angle Torque Wrench
Models covered

EDIT PRE-SET VALUE
Notice Idle 120 Sec.
Press the Button 2 times
Press the Button
LCD Blinking Beep sound
LED Power OFF
Press the Button 1 Sec.
Operation mode
2
low self-discharge
During Self Calibration
UM-3 (AA) UM-3 (AA) UM-3 (AA)
1. Please take the battery out if you do not use wrench for a long time .
2. Do not mix battery types or combine used batteries with new ones.
3. Sweat,oil and so on can prevent a battery’s terminal from making electrical contact.
To avoid this, wipe both terminals before loading a battery .
4. Dispose of batteries in a designed disposal area. Do not throw batteries into a fire.
ON
OFF
Preset Angle Setting
Keep Zero Degree
Keep Zero Percent
BATTERY INSTALLATION & POWER
BATTERY MAINTENANCE
STATUS ICON DESCRIPTION
ON & OFF
During Self Calibration (Do not move the wrench within 8 seconds)
Select
Unit Select
Auto Reset Mode
Torque Angle Mode
Track Mode
(Auto reset 2 seconds)
Angle Range Setting
Preset Angle Setting
(Example：META-200N)

50 SETS OF HISTORICAL TORQUE VALUES
MEMORY BLOCK
3
Quick release button design.
Push the button to release socket.
PUSH
left right center
Position of ratchet lever for clockwise/counter
clockwise tightening.
Choose quality socket
S
M
+
-
C
S
M
+
-
C
S
M
+
-
C
S
M
+
-
C
Latest data First data
PRECAUTIONS
RS-232 CONNECTION
Insert square drive securely to the fitting or socket.
POSITION
S
M
+
-
C
RS-232 port
Back to main screen
C.C.W.
C.W.
S
M
+
-
C
S
M
+
-
C
RESET DIRECTION LIGHT
Red LED
Green LED
Yellow LED
Over the pre-set deviating range
Within the pre-set deviating range
Lower then the pre-set deviating range
Over the pre-set angle
(Allowable angle error)
Lower than the pre-set angle
Red
Green
Yellow
Auto reset mode Torque angle mode
Equal the pre-set angle,Lower or equal
the allowable angle error

E-mail:[email protected]om
www.matatakitoyo.com Made in Taiwan
MATATAKITOYO TOOL CO., LTD.
No. 63, Ln. 493, Sec. 3, Zhongshan Rd., Tanzi Dist.,
Taichung City 42754, Taiwan
TEL : [phone]
Manufacturer JUN. 2020
02
Edition
DIMENSIONS
1 Years
5000 Times
Unit : mm
H
B
A
W
ØD
ØD1
L
S
M
+
-
C
Slow Rapid
Beep speed
Torsion
Red
Green
Yellow
Over the range
Within the range
Lower then the range
AUTO RESET MODE TRACK MODE
Torque
Time
0
Tolerance：1%~9%
Ex. : 100Nm±5％
Angle=0°
Tolerance：0%
105Nm
100Nm
95Nm
65Nm
0.75
0.76
0.95
1.06
1.35
1.90
META-30N
META-60N
META-100N
META-100NS
META-200N
META-350N
360
360
440
440
524
640
3-30 Nm
6-60 Nm
10-100 Nm
10-100 Nm
20-200 Nm
35-350 Nm
1/4”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
25.5
25.5
25.6
25.6
25.6
25.6
L ØD
21.7
26.8
26.8
35.1
35.1
40.0
40.0
38.0
38.0
37.3
37.3
37.3
37.3
H ØD1
7.3
11.0
11.0
11.0
15.7
15.7
15.7
B
28.5
28.5
35.6
35.6
46.0
46.0
WKG
A
ITEM NO. Range
MAINTENCE AND STORAGE
1. Clean this tool by wiping with a clean cloth after
operation and storage in a dry environment. Do not dip
any type of liquid in this tool. This may damage the
internal of this tool.
2. This tool should be recalibrated a period of 1 years, or
5,000 cycles, whichever occurs first. To contact with
local vendor, an authorized repair center for supporting.
WARNING
OPERATION EXAMPLE
Example：
Set number：6
Pre-set Torque：20 Nm
Pre-set Angle：35°
Angle Range Setting：38°
S
M
+
-
C
Torque Angle Mode
20.0 Nm
Red LED
Yellow LED
Green LED
Long Beep Reach 20 Nm (Show angle 0°)
Start 0 Nm
(Torque Preset Value 20 Nm)
Angle Setting Point from the Presetting 35°
Angle Range Setting 38°
Qualified range：35°~38°