Matatakitoyo Torque Tools PIT User manual

Main Scale
Graduation Scale
Adjustment Nut
Hand ForceGripTube
Hook Jaw
Heel Jaw
Lock Ring
A. Maintain Gap Between Hook Shank and Work Piece.
B. Wrench Too Small For Work Piece, Hook Shank Touching Work Piece.
1. Study this instruction before use.
2. This torque wrench as calibrated and tested before leaving the factory is certified to meet the current standard specification and has an
accuracy of ±6%.
3. THIS TOOL IS A PRECISION MEASUREMENT AND DESIGNED FOR MANUAL TIGHTENING FASTERNERS ONLY.
DO NOT USE IT AS A NUT BREAKER OR FOR ANY OTHER PURPOSE.
4. Over torque will cause tool damage and personal injury.
5. Do not use this tool near rotating machinery.
6. Disassemble this tool or make any adjustments will result of losing accuracy and void the warranty.
7. Do not continuously apply force after hear click or feel shock.
8. Do not use any format of extension on the handle of the tool. This will not only damage the tool, also affect the accuracy.
9. Do not immerse grease inside ratchet head. It may cause unexpected damage.
10. Use special care at minimum torque setting.
11. Please wear gloves and goggles when working.
Manual
Torque wrench
Manual
WARNING
■ When using a pipe wrench of any size, a gap must be maintained between
the shank of the hook jaw and the work piece. (See A)
■ This permits the two gripping points (heel jaw teeth and hook jaw teeth)
to produce the gripping action of the wrench. Allowing the shank of the
hook jaw to contact the work piece greatly reduces the gripping action
and can cause slippage. It may also result in the failure of the hook jaw.
(See B)
Do not continuously apply force after hear click
or feel shock.
STOP
CLICK
BEFORE STARTING
TORQUE
The size of the hook jaw opening can be controlled by adjusting the nut.
PIT
OPERATION MANUAL
Adjustable Torque Ｗｒｅｎｃｈ,
PIPE & CONSTRUCTION APPLICATIONS
Models covered
HOW TO USECONTENTS

MAY 2020
01
Edition
WH
L
ØD
N-m
KG
ITEM NO. Range H
Pipe
Capacity
Pipe Capacity
PIT-210N
PIT-350N
PIT-500N
48
63
63
67.8
83.8
83.8
W
33.5
38.6
38.6
L
589.6
827.0
922.3
ØD
39.1
47.0
47.0
40-210 Nm
70-350 Nm
100-500 Nm
1 Nm
1 Nm
2.5 Nm
2.96
3.70
4.30
KG
H
PIT-150F
PIT-250F
PIT-300F
48
63
63
67.8
83.8
83.8
W
33.5
38.6
38.6
L
589.6
827.0
922.3
ØD
39.1
47.0
47.0
30-150 ft.lb
50-250 ft.lb
50-300 ft.lb
1 ft.lb
1 ft.lb
2.5 ft.lb
2.96
3.70
4.30
Unit : mm
Accuracy : ± 6%
Metric SAE
ITEM NO. Range Pipe
Capacity
0
28
210
170
130
90
50
190
150
110
70
200
160
120
80
40
180
140
100
60
N-M
1 Years
5000 Times
1. Please return torque value to just below lowest reading when not in use. Do not turn below lowest reading. (see C)
2. If this tool has not been used for a period of time, it shall be preloaded several times at its maximum torque setting.
This will allow internal lubricant to recoat.
3. Clean this tool by wiping with a clean cloth after operation and storage in a dry environment.
Do not dip any type of liquid in this tool. This may damage the internal of this tool.
4. This tool should be recalibrated a period of 12 months, or 5,000 cycles, whichever occurs first.
To contact with local vendor, an authorized repair center for supporting.
BHOW TO SET TORQUE VALUE
MAINTENCE AND STORAGE
TORQUE CONVERSION FACTORS
SPECIFICATION
For example : ITEM NO. PIT-210N
To set torque to 135 Nm. Firstly push down and hold the lock ring and
turn the handle clockwise until the upper edge to 135 Nm (see A) and
the reading “5” on the long tube must align with the ccntcrlinc of scale
perpendicularly so as to acquirc 135 Nm. (See B)
0
28
N-M
210
170
130
190
150
200
160
120
180
140
64
N-M
210
170
130
190
150
200
160
120
180
140
0
28
210
170
130
90
50
190
150
110
70
200
160
120
80
40
180
140
100
60
0
28
210
170
130
90
50
190
150
110
70
200
160
120
80
40
180
140
100
60 A
1 2 3 B
C
0
28
210
170
130
190
150
110
200
160
120
180
140
100
1. Push down the lock ring to unlocked.
2. Turn the adjustable handle Clockwise or Anti-clockwise
(Right or left) to set the desired torque.
3. Pull upper the lock ring to set finished.
Unlock Lock
Set
Units to be
converted
1 mN.m
1 cN.m
1 N.m
1 ozf.in
1 lbf.in
1 lbf.ft
1 gf.cm
1 kgf.cm(kp.cm)
1 kgf.m(kp.m)
1
10
1000
7.062
113
1356
0.098
98.07
9807
0.1
1
100
0.706
11.3
135.6
0.01
9.807
980.7
0.001
0.01
1
0.007
0.113
1.356
0.0001
0.098
9.807
0.142
1.416
141.6
1
16
192
0.014
13.89
1389
0.009
0.088
8.851
0.0625
1
12
0.0009
0.868
86.8
0.0007
0.007
0.738
0.005
0.083
1
0.00007
0.072
7.233
10.2
102
10197
72
1152.1
13826
1
1000
100000
0.01
0.102
10.2
0.072
1.152
13.83
0.001
1
100
0.0001
0.001
0.102
0.0007
0.0115
0.138
0.00001
0.01
1
=mN.m =cN.m =N.m =ozf.in =lbf.in =lbf.ft =gf.cm =kgf.cm
(kp.cm)
=kgf.m
(kp.m)
Corresponding unit
Conversion-formula :
Units to be converted × Factor = Corresponding unit
Example : Convert 5 lbf.ft into cN.m
Solution : 5 × 135.6 = 678 cN.m
E-mail:[email protected]om
www.matatakitoyo.com Made in Taiwan
MATATAKITOYO TOOL CO., LTD.
No. 63, Ln. 493, Sec. 3, Zhongshan Rd., Tanzi Dist.,
Taichung City 42754, Taiwan
TEL : [phone]
Manufacturer