Memjet AFINIA LABEL L701 Series User manual

User’s Guide v1.3
L701 Printer Series

2
Copyright © 2018 Afinia Label. All rights reserved.
No part of this document may be photocopied, reproduced, or translated to another language without the
prior written permission of Afinia Label.
Trademarks
Firefox is a trademark of the Mozilla Foundation.
Intel and Intel Core are trademarks of Intel Corporation in the U.S. and/or other countries.
Java and Oracle are registered trademarks of Oracle and/or its affiliates.
Microsoft, Windows, Windows Vista, and Windows Server are registered trademarks of Microsoft
Corporation in the U.S.A. and/or other countries.
Memjet is a trademark of Memjet Ltd.
Edition
Edition 1, March 2018.
FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

3
Safety Precautions
Electrical Shock Hazard
Do not disassemble any part of your printer. There are no user-repairable parts
inside the printer. Disassembly of any part of the printer will void all warranties.
Fire Hazard
Keep the printer well away from all heat sources and flammable substances.
Switch your printer off immediately and unplug the power cord from the wall socket
if you notice any of the following:
• Smoke rising from the printer.
• An acrid smell coming from the printer.
• Sparks being emitted from printer.
Contact your supplier as soon as possible.
WARNING: Hazardous Moving Parts
Keep fingers and other body parts away from the printer.
Installation
• Install the printer on a flat, level surface.
The printer must remain level at all times. Tilting the printer may cause undue
leakage of ink and affect performance and print quality.
• Avoid wide temperature variations.
Install the printer in a protected location away from direct sunlight, open
windows or any other places subject to temperature extremes.
Power Supply
• Always use the Power button on the control panel to turn the printer off.
Removing power to the printer in any other manner may damage the printer.
• Use only the supplied power cord.
Use of any other power supplies or cords may damage the printer and void your
warranty.
Input Rating 100–240 VAC, 50/60 Hz, 3.6 A
Operating Temperature 15°C to 35°C (60°F to 95°F)

4
Printer Usage
• Ensure adequate ventilation to the printer.
Blocking ventilation openings around the printer may cause it to overheat and
become damaged.
• Keep liquids and heavy objects away from the printer.
Heavy objects may warp the outer shell, damaging the printer. Liquids may
discolor or damage the skin and, if they penetrate it, may damage the printer
beyond repair.
• Use only authorized consumables.
Use of any printhead other than authorized Memjet technology printheads will
damage the printer and void your warranty. Use of unauthorized inks or ink
cartridges may damage the printer and will void your warranty.
• Clear media jams promptly.
To avoid further problems, promptly attend to all media jams, as well as any
other cause of printer failure.
• If you are moving the printer, allow sufficient time after installation for the
temperature and humidity of the internals of the printer to arrive at equilibrium
with the surroundings.

5
Contents
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Using the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts of the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Installing the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connect by USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Using the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selecting the Security Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Choosing Label Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading Label Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Loading Fanfold Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Printing Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Change Default Settings in Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Select the Media Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Adjust Alignment for Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Printing Borderless (Full-Bleed) Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Saving Custom Media Size Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Turning Off the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Managing Printer Security (Administrator). . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Embedded Web Server (EWS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Other Support Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Printer Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Guidelines for Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Replacing an Ink Cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cleaning the Printhead. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Replacing the Printhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Opening/Closing the Clamshell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cleaning Debris from the Cutting Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Cleaning the Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Replacing the Output Module/Cutter Assembly. . . . . . . . . . . . . . . . . . . . . . . . 49
Replacing the Service Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Replacing the Transfer Wiper Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Replacing the Aerosol Fan Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Replacing the Waste Ink Absorber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
If Error Messages Appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Poor Print Quality or Incorrect Printout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Other Printing Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Clearing a Media Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Clearing Clogged Ink Nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Adjusting Sensor Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

6
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Additional Networking Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
If the Printer Has a Static IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
If the Connection to the Printer Has Changed. . . . . . . . . . . . . . . . . . . . . . . 76
Config Options on the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Printer Interface (GPIO) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Full Bleed Label Spec Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Circle Label Spec Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Memjet Printhead Best Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Regulatory Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Worldwide Afinia Label Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Using the Printer 7
Chapter 1
Using the Printer
Parts of the Printer 8
Installing the Printer 9
Choosing Label Media 13
Loading Label Media 17
Loading Fanfold Media 19
Printing Labels 20
Printing Borderless (Full-Bleed) Labels 24
Saving Custom Media Size Settings 25
Turning Off the Printer 26
Managing Printer Security (Administrator) 27
Embedded Web Server (EWS) 29
Other Support Tools 37
NOTE: Once the printer has been set up, be sure to change the security passwords
using the Embedded Web Server (EWS). See Change Passwords on page 27.

8Using the Printer
Parts of the Printer
Control Panel
Top Cove r
Front Cover
Output Slot
GPIO Port
USB Port
Ethernet Port
Power Socket
Power Switch
Media Feed Slot
Media Feed Cover

Using the Printer 9
Installing the Printer
The printer can be connected to your computer either by direct USB connection or
by an Ethernet connection.
Both connection methods require that the printer be installed with administrative
privileges.
The printer must be turned on to install.
Connect by USB
Do not connect the printer to the computer until you are prompted.
1. Download the latest driver via
https://afinialabel.com/product-support/l701-support/
2. If the installer doesn’t open automatically, open the disk in Windows Explorer
and run Check.exe
3. Click InstallDriver and
follow all steps
4. When asked the Printer
Connection, select Configure
toprintusingUSB and click
Next
5. When asked if drivers should
be installed, click Install
6. Connect the USB cable when
prompted

10 Using the Printer
Using the Control Panel
The printer is ready to print when the control panel displays Printer Online . The Data
and Status LEDs together with messages indicate the printer status and any
potential problems (Table 1).
The control panel also shows the estimated levels of the ink cartridges. In the
example below, the yellow ink cartridge level is between 25 to 50%.
The icons above the printer buttons indicate their functions, which change
depending on the current operation (see Table 2).
Printer Online
Power LED
Power Button
Printer Buttons
Data LED
Status LED
Ink Status
Table 1 Printer LEDs
LED Description
Data LED
Blinking Printer is receiving data from the computer.
On There are print jobs in the printer memory.
Status LED
Blinking • Printhead is being serviced, or
• Attention needed; a message will be displayed. (See If Error
Messages Appear on page 62.)
On • An error has occurred; a message will be displayed. (See If
Error Messages Appear on page 62.)

Using the Printer 11
The icons above the printer buttons indicate their functions (Table 2).
• When the printer is online, press (
Config ) to access the configuration menus.
The options are described in Config Options on the Control Panel on page 77.
• Press and to scroll through the menus.
• Press (
Select ) to select an option or setting.
• Press (
Return ) to return to the previous menu.
Table 2 Printer Buttons
Function Description
Config Access the Configuration menus.
Up, Down Move through the menu options.
Select Select a menu option or confirm a setting.
Return Return to previous menu.
Unload Media Unload the labels.
Pause, Resume Pause or resume printing.
If printing Roll to Roll, the printer pauses for 10 seconds,
then prints the next page and pauses again. It will
continue to print and pause.
Cancel Cancel printing.
Printer Online
CONFIGURATION
1. Setup

12 Using the Printer
Selecting the Security Level
By default, the printer powers up in security Level 0 (operator), which does not
allow changes to some printer parameters. To make changes, select security Level 1
(supervisor) and enter the password provided by your administrator.
Security Level 2 gives administrator access to all functions.
1. On the control panel, select (
Config )  SETUP  SECURITY  Level 1 or Level 2 .
2. Enter the 3-digit password.
3. Press to return to the main menu.
000
Printer Online
CONFIGURATION
1. SETUP
SETUP
2. SECURITY
SECURITY
2. Level 1
(Config)
(Select)
(Select)
(Select)
ENTER PASSWORD
Press , to set.
Press to move to next digit.

Using the Printer 13
Choosing Label Media
Ensure that the label media meets the requirements for the printer (see Table 3 and
the following illustrations). Always test the media first to see if it meets your
expectations. To check the compatibility of label media, print the barcodes test page.
Figure 1 Media Roll
Table 3 Media specifications
Media Type and Dimensions
Media type Gloss, semi-gloss, and matte.
Label width 2.0” to 8.5” (50.8 mm to 215.9 mm)
Label length Continuous/Roll to Roll: Maximum 40” (1.016 m)
Roll to Cut/Print and Present: Maximum 8" (203.2mm)
Label thickness Maximum 0.01” (0.3 mm) (including liner, if any)
Minimum 0.005” (0.13 mm)
Core size 3” (76.2 mm)
Roll diameter Maximum 6” (152.4 mm)
Media Handling
Print mode • Roll to Cut
• Print and Present (non-peel)
• Roll to Roll
Detection • Gap
• Continuous
• Black mark
Coating on
JI
Minimum Maximum
I 3.0” (76.0 mm) cardboard core 3.0” (76.0 mm) cardboard core
J N/A Up to 6” (152.4 mm)
the outside

14 Using the Printer
Figure 2 Gap (Transmissive) Media (non Full-Bleed*)
*SeeAppendixforspecsanddiagramsofFullBleedandCircleLabelLayouts
A
BC
D
E
Minimum Maximum
A 0.125”(3.0 mm) 0.3” (8.0 mm)
B 0.0 2.0” (50.8 mm)
C 0.0 0.4” (10mm)
D 2.0” (50.8 mm) 8.5” (216.0 mm)
E 2.0” (50.8 mm) 40.0” (1016.0 mm)

Using the Printer 15
Figure 3 Black Mark (Reflective) Media (non Full-Bleed*)
*SeeAppendixforspecsanddiagramsofFullBleedandCircleLabelLayouts
E
G
H
D
Minimum Maximum
D 2.0” (50.8 mm) 8.5” (216.0 mm)
E 2.0” (50.8 mm) 40.0” (1016.0 mm)
H 1.0” (25.4 mm) 8.5” (216.0 mm)
G 0.125” (3.0 mm) 0.3” (8.0 mm)
Reverse side of tag stock

16 Using the Printer
Print Test Page
Load 4” x 4” or larger labels. Be sure to select the label type (continuous, gap, or black
mark) in the EWS Diagnostics page.
1. On the control panel, select (
Config )  MAINTENANCE  PRINT TEST PAGE 
Barcodes .
2. Verify the following on the test page:
• Label is printed in black with no other color visible.
• The text is legible.
• The barcodes are readable.
• No ink smear, color mix or streaks.
Printer Online
CONFIGURATION
2. MAINTENANCE
MAINTENANCE
1. PRINT TEST PAGE
PRINT TEST PAGE
1. Barcodes
(Config)
(Select)
(Select)
(Select)
Sample Barcodes Test Page

Using the Printer 17
Loading Label Media
Figure 4 Media path
1. Loosen the knob and remove the roll cover.
2. Load the media roll.

18 Using the Printer
3. Push the roll cover against the media roll. Make sure the slot in the roll cover is
over the flat side of the spindle. Then tighten the knob.
4. Feed the media into the printer:
aOpenthemediafeedcover.
b Feed the media under the arm and into the printer. Wait for the printer to load
the media.
c Slide the media guide to the edge of the media.
5. Close the media feed cover.
Slot
Flat side

Using the Printer 19
Loading Fanfold Media
Figure 5 Fanfold media path
1. When loading fanfold media, place the media stack 15 mm or more away from
the rear of the printer.
2. Feed the media into the printer, aligning it with the left side of the media feed
slot. Wait for the printer to load the media.
3. Slide the media guide to the edge of the media.
15 mm

20 Using the Printer
Printing Labels
The printer is ready to print when the control panel displays Printer Online .
1. Select the Print command from your application.
2. Select the printer and click the Setup, Properties or similar button.
The print settings displayed are the defaults that were set in the printer driver.
3. Change the print settings if needed.
NOTE: Ensure the media settings (e.g. label size) match the media loaded in the
printer.
4. Print the document.
Any changes to the settings only apply to the current print job. Once you exit the
application, the changes may be lost. Make the changes in the printer driver if you
wish to keep the settings as the default for all print jobs.
Change Default Settings in Printer Driver
To select the default print settings that will be used for all print jobs:
1. From the Windows Start menu, select Devices and Printers1.
2. Right-click the printer, and select Printing preferences.
3. Make the changes (see Figure 6) and click OK to save.
1. For Windows 7. The steps will differ for other Windows versions.