Mercia Garden Products 01OVLPA0705SDFW-V1 Instruction manual

7X5 OVERLAP APEX
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
Please retain product label and instructions for future reference
General Instructions
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air ow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy or
extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above
the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
**Protim Aquatan T5 (621)**
Your building has been dip treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
REGISTER FOR YOUR
ANTI-ROT
GUARANTEE TODAY
PLEASE SCAN HERE:

P 2
01OVLPA0705SDFW-V1 & 01OVLPA0705SDFW-V1-NW
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
01OVLPA0705SDFW-V1
01OVLPA0705SDFW-V1-NW
Overall Dimensions:
Length = 2090mm
Width = 1606mm
Height = 1925mm
Base Dimensions:
Length = 2071mm
Width = 1466mm
Building Content:
Door Gable QTY 1
AI-01OVLPDG1410X1887-V1
Back Gable QTY 1
AI-01OVLPPG1410X1887-V1
Plain Side QTY 2
(NW ONLY)
AI-01OVLPPS2076X1567-V1
Window Panel QTY 1
(FW ONLY)
AI-01OVLPWS2076X1567-V1
1 2 3 4
Floor QTY 1
AI-01OVLPF2066X1456-V1
Roof QTY 2
PI-03-0225
Door QTY 1
AI-01MBDR1660X660-V1
5 6 7
10
11
12
13
14
Fascia 12x60x851mm QTY 4
S1260-851mm
Fixed Window Strip 12x30x546mm QTY 5 (FW ONLY)
S1230-546mm
Cover Trims 12x45x1575mm QTY 4
S1245-1575mm
Ridge Bar 28x28x2020mm QTY 1
F2828-2020mm
Finial QTY 2
SHED DIAMOND FINIAL
8
9
17
Door Beading Strip 12x28x1590mm QTY 2
S1228-1590mm
T Hinge QTY 2
PI-02-1041
Plastic Window Cill
(FW ONLY)
PI-08-0013
Felt
Styrene QTY 2
(FW ONLY)
PI-05-0114
18
20
L-Bracket QTY 2
PI-07-0012
16
Turn Button QTY 2
PI-07-0034
19
15
Eaves Frame 28x28x2106mm QTY 2
F2828-2106mm
Nail Bag
Felt Tacks x 108
20mm Screw x 8
30mm Screw x 63
50mm Screw x 28
40mm Screw x 44

P 3
Remove transportation
blocks from the bottom of
each panel before beginning
assembly. Each Panel should
have two blocks.
Pre Assembly
Fix the T Hinges onto the
doors and door frame as
shown. Ensure that the
screws go through the
cladding and into the
framing behind.
14x30mm screws
30mm
screw
Pre drill
hole
1
7
15
Place the oor on a rm and level base, ensure the
base has suitable drainage free from areas where
standing water can collect. See the front page for
base requirments.
Step 1
5
Do not secure the building to the oor until
the roof is tted. Fix the panels onto the
oor using 50mm screws in alignment with
the oor joists
Fix the corners with 50mm screws as shown
in diagram.
Position the panels so there is equal spacing
between the oor and cladding on all 4
sides
Step 2
3
2
3x50mm Screws
Pre drill
hole
50mm
screw

P 4
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Step 3
9x50mm Screws
Fix the corners with 50mm
screws as shown in diagram.
1
4
Use for no
window buildings
3
Pre drill
hole
50mm
screw
Step 4
8x20mm Screws
Place the ridge bar in between the front
and back gables. Ensure the top corners of
the ridge bar sit ush with the top points
of the door gable. Fix the ridge bar to the
gable using one L bracket for each end.
Fix with 4x20mm screws each.
12
20
20mm
screw
Pre drill
hole
Step 5
Fix two eaves frames to each roof
sheet using 3x30mm screws per eave.
Fix the roof sheets to the roof ensuring
they come together at the top using
40mm screws directly through the
roof sheet at the top. Make sure to
attach the roofs to the ridge bar.
13
6
30mm
screw
13
12x 30mm Screws
28x 40mm Screws
40mm
screw
Pre drill
hole
Step 6
bOnce the roof is xed attach
the building to the oor
with 50 mm screws.
16x 50mm Screws
50mm
screw
Pre drill
hole

P 5
108x Tacks
18
Step 7
Cut the felt into 2 sheets at 2206mm
and x onto the roof using felt tacks
as shown in diagram ensuring there is
50mm overhang around the sides.
HANDLE
WITH CARE
12
3
4
Felt
tacks
18
Fit the Cover Trims to the front and back
of the building as shown in the illustration
using 30mm screws. Trim the length of
the cover trims to the required size before
tting if necessary.
12x30mm Screws
10
Step 8
10
10
30mm
screw
Pre drill
hole
Step 9
16x40mm Screws
Attach the faiscas to the roof
leaving a slight overhang at the
top.
Fit the fascias to the roof over
the felt and secure in place with
40mm screws as shown.
14
8
8
8
14
8
40mm
screw
Pre drill
hole