METHVEN SATINJET ESCAPE MKII User manual

SATINJET ESCAPE MKII RAILSHOWER/
HANDSET
INSTALLATION GUIDE
Issue B
436670
Methven warrants this product against manufacturing defects and that it is suitable for use
under the operating conditions specified in this instruction sheet.
For your warranty please refer to www.methven.com/au or call Customer Service 1300 METHVEN
Australia
1300 638 483
To clean the chrome-plated surface use a soft
cloth, soap and warm water. Never use cleaning
agents that contain a corrosive acid or a scouring
additive.
CLEANING
Water contains lime which remains on the
surface after the water has evaporated. These
lime deposits can be prevented from forming by
wiping immediately after use.
Important Installation Considerations
1. NOTE: Some showers may not provide an effective shower when used
with gravity fed heated water systems or where pressures are less
than 150kPa at the outlet. Additionally showers with flow rates of less
than 9L/min may not allow the following to function correctly:
_ some instantaneous water heaters
_ some tempering valves
_ some thermostatic mixing valves
2. Some shower heads only operate correctly when hot and cold water
supplies are both mains pressure and may not be suitable for some
instantaneous hot water services.
3. When water pressure is in excess of 500kPa a pressure limiting device
is required in accordance with AS/NZS 3500 1.12 recommendation.
4. Domestic and Commercial warranty terms and conditions vary.
For full warranty terms and conditions refer to
www.methven.com
TECHNICAL SPECIFICATIONS
Operating Pressure:
Min 150kPa, Max 500kPa.
Recommended installation of a pressure limiting
valve if supply exceeds 500kPa
Operating Temperature:
Recommended hot water supply 50°C,
maximum 70°C. AS 3500 requires all hot
water supplies to any sanitary fitting to be
tempered to 50°C.
Inlet connections: All 1/2” BSP
Notes:
●After installation all connections must be checked
for leaks.
●All installations must be carried out in compliance
with relevant water regulations.
Do not use any
sharp objects to
clean nozzles
9

Elbow
1.
5.
3.
7.
2.
6.
4.
Secure the wall boss housings in
desired position with 4 screws us-
ing wall plugs if required.
Check the mounts are vertical.
Ensure the grub screws are
located as shown.
Attach the shelf to the
rail from the end with
the endcap already
fitted.
NOTE: ENSURE
PROTECTION
PADS ARE USED
BETWEEN WALL
BOSSES AND TILES.
Fit end cap to top of
rail. Ensure drainage
hole is at back.
Match the mountings
up to the wall bosses
and push into place.
Slide the rail up and
down if required to
centralise the rail on
the brackets.
Once satisfied that
the rail is centralised
remove the rail and
tighten the tensioning
screws until they lock.
Relocate the rail
onto wall bosses and
tighten grub screws
top and bottom.
Fit the internal mounting
brackets by locating in slot
and rotating 90° as shown.
Once located tighten the
screws finger-tight.
grub screw underside
grub screw topside
Wall Boss Housing
Grub Screw
Rail
Hose
Slider
Escape MKII
Handset
Shelf
Screw
Internal Mounting Bracket
Floor Fitted endcap
510-645mm
1850mm (recommended)
NOTE: TO LOOSEN SLIDERS
GRIP ON RAIL ROTATE SIDE
PIECE ANTI-CLOCKWISE.
ROTATE CLOCKWISE TO
TIGHTEN.
NOTE: GRUB SCREW HOLES
ARE NOT FULLY ALIGNED
PRIOR TO GRUB SCREW
BEING FITTED, THEREFORE
SCREW MAY BE STIFF TO
TIGHTEN.
8.
Non-Swivelling Cone
Filter Washer
Flat Washer
Swivelling
Cone